• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.18 no.1
• /
• pp.262-268
• /
• 2017

The energy consumption of buildings is approximately 20.5% of the total energy consumption, and the interest in energy efficiency and low consumption of the building is increasing. Several studies have performed energy analysis and evaluation. Energy analysis and evaluation are effective when applied in the initial design phase. In the initial design phase, however, the energy performance is evaluated using general level information, such as glazing area and surface area. Therefore, the evaluation results of the detailed design stage, which is based on the drawings, including detailed information of the materials and facilities, will be different. Thus far, most studies have reported the analysis and evaluation at the detailed design stage, where detailed information about the materials installed in the building becomes clear. Therefore, it is possible to improve the accuracy of the energy environment analysis if the energy environment information generated during the life cycle of the building can be established and accurate information can be provided in the analysis at the initial design stage using a probability / statistical method. On the other hand, historical data on energy use has not been established in Korea. Therefore, this study performed energy environment analysis to construct the energy environment historical data. As a result of the research, information classification system, information model, and service model for acquiring and providing energy environment information that can be used for building lifecycle information of buildings are presented and used as the basic data. The results can be utilized in the historical data management system so that the reliability of analysis can be improved by supplementing the input information at the initial design stage. If the historical data is stacked, it can be used as learning data in methods, such as probability / statistics or artificial intelligence for energy environment analysis in the initial design stage.

• Journal of Society of Preventive Korean Medicine
• /
• v.7 no.1
• /
• pp.17-28
• /
• 2003

We met results like the followings through the literatures and questionnaires about the tasks and solutions about the insurance fee of packed medical herbs. 1) It's turned out that 74.8% of herb doctors agrees to the insurance fee of packed medical herbs. However, in comparison with the same survey of the herb doctor association the percentage of general approval went somewhat lower, and especially the percentage of 'positive approval' became notably lower$(43.7%{\rightarrow}26.5%)$ and the percentage of 'active objection' raised about 2 times$(6.8%{\rightarrow}12.9%)$. Inquiring into the approval reasons on the insurance fee application of packed medical herbs some heads such as 'development toward treatment medical science' and 'decrease of publics burden' were higher than the one of 'management income and expenditure.' 2) As a result of the research, 36.0% of the patients and 42.8% of the residents recognized that the pay range of Chinese herb health insurance is narrow. They recognized that less people have the experiences of Chinese medical hospital use and internal application of the packed medical herbs as they are older, men rather than women. 85.4% of the patients and 74.9% of the residents agreed on the insurance pay of packed medical herbs. It's shown that they agree on the Chinese medical hospital use more as the economic standard is lower, on the insurance pay as they have ever taken the packed medical herbs. In the aspect of increase of insurance fee, 66.7% of the patients and 44.3% of the residents agreed on the insurance pay of packed medical herbs, and 18.1% and 36.1% disagreed on the insurance pay of packed medical herbs. The main objective reason why they disagree on the insurance pay of packed medical herbs was 'because the insurance fee goes up higher,' which answered 95.2% of the patients and 78.8% of the residents. 7.22% of the patients and 1.80% of the residents answered that they can pay more insurance fee in case of the insurance pay of packed medical herbs. However, in the priority order of the insurance pay, it hold the 5th position between 2 target research groups which was less than medical examination, charges for hospital accommodation and taking MRI. 3) According to the result of analysis about the cost of packed medical herbs, current practice price is 115,000 won and the average prime cost of a packed medical herb is 73,000 to 106,000 won. It's examined that the herb doctors regard that 95,000 won will be reasonable when the packed medical herb is payed in insurance. However, it was found out that the public generally thinks that the price would be appropriate on the level of 30,000 to 40,000 won and the percentage of the answers of 20,000 won to 30,000 was fairly high. 4) the central system of a prescription should be change into the central system of demonstration and the sick and wounded. 5) To solve this problem, the government should regulate it to pass by the circulation gradation of [importer, $peasantry{\rightarrow}manufacturer{\rightarrow}wholesaler{\rightarrow}distributor$(Chinese medical hospital, pharmacy dispensary of Chinese medicine)]And it should intervene into the quality and the circulation steps of Chinese medicine through 'the office or organization which is in charge of certification of Chinese medicine' and 'the office or organization which is in charge of the circulation of Chinese medicine.' And some actions such as simple severance, lavation, drying should be included into the conception of manufacture and the boundary between food and medical supplies should be made at a manufactory. And the regulation of standardized goods at one's own house should be improved so that, the peasantry can sell the materials of Chinese medicine only to the manufacturer. 6) In company with the insurance pay of packed medical herbs, the study about the separation of dispensary from medical practice in the Chinese medicine should be accomplished.

• Journal of Soil and Groundwater Environment
• /
• v.12 no.1
• /
• pp.87-96
• /
• 2007

Risk assessment was carried out in order to improve the remediation and management strategy on a contaminated gunnery site, where a flood control reservoir is under construction nearby. Six chemicals, including explosive chemicals and heavy metals, which were suspected to possess risk to humans by leaching events from the site were the target pollutants for the assessment. A site-specific conceptual site model was constructed based on effective, reasonable exposure pathways to avoid any overestimation of the risk. Also, conservative default values were adapted to prevent underestimation of the risk when site-specific values were not available. The risks of the six contaminants were calculated by API's Decision Support System for Exposure and Risk Assessment with several assumptions. In the crater-formed-area(Ac), the non-carcinogenic risks(i.e., HI values) of TNT(Tri-Nitro-Toluene) and Cd were slightly larger than 1, and for RDX(Royal Demolition Explosives), over 50. The total non-carcinogenic risk of the whole gunnery range calculated to a significantly high value of 62.5. Carcinogenicity of Cd was estimated to be about $10^{-3}$, while that of Pb was about $5\;{\times}\;10^{-4}$, which greatly exceeded the generally acceptable carcinogenic risk level of $10^{-4}{\sim}10^{-6}$. The risk assessment results suggest that an immediate remediation practice for both carcinogens and non-carcinogens are required before the reservoir construction. However, for more accurate risk assessment, more specific estimations on condition shifts due to the construction of the reservoir are required, and more over, the effects of the pollutants to the ecosystem is also necessary to be evaluated.

• Clean Technology
• /
• v.26 no.2
• /
• pp.151-157
• /
• 2020

Rapid urbanization has elevated the risk of urban flooding due to the increase in the impervious surface, causing environmental disasters and environmental pollution problems, such as lowering the groundwater level and increasing water pollution. In Korea, low impact development (LID) techniques have been introduced to minimize these environmental impacts and maintain the water cycle soundness. However, most small-scale development projects are in blind spots because there is no legal basis for rainfall runoff management. Small-scale development projects that increase the surface runoff of rainwater are required to mandate the application of LID facilities in accordance with the polluters' responsibility principle. Therefore, it is necessary to implement a preliminary consultation system for water cycle recovery. This study focuses on the cost-benefit analysis on the application of LID techniques for small-scale development projects. The scale of nationwide small-scale development projects used for cost-benefit analysis were defined as buildings with a land area of more than 1,000 ㎡ or a total floor area of 1,500 ㎡. As a result of analyzing the cost-benefits from the installation of LID facilities, they were found to be much lower than the economic standard value of 1. This might be due to the high cost of facilities compared to the scale of the project. However, considering the overall environmental value of improving the water environment and air quality by the installation of LID facilities and the publicity of reducing the operating cost of sewage treatment facilities, the introduction of a prior consultation for small-scale development projects is inevitable. In the future, institutional and financial support from local governments is required to improve the cost-benefits with the introduction of a prior consultation for small-scale development projects.

• Journal of Korea Water Resources Association
• /
• v.46 no.12
• /
• pp.1235-1247
• /
• 2013

This study is to evaluate the climate change impact on future storage behavior of Chungju dam($2,750{\times}10^6m^3$) and the regulation dam($30{\times}10^6m^3$) using SWAT(Soil Water Assessment Tool) model. Using 9 years data (2002~2010), the SWAT was calibrated and validated for streamflow at three locations with 0.73 average Nash-Sutcliffe model Efficiency (NSE) and for two reservoir water levels with 0.86 NSE respectively. For future evaluation, the HadCM3 of GCMs (General Circulation Models) data by scenarios of SRES (Special Report on Emission Scenarios) A2 and B1 of the IPCC (Intergovernmental Panel on Climate Change) were adopted. The monthly temperature and precipitation data (2007~2099) were spatially corrected using 30 years (1977~2006, baseline period) of ground measured data through bias-correction, and temporally downscaled by Change Factor (CF) statistical method. For two periods; 2040s (2031~2050), 2080s (2071~2099), the future annual temperature were predicted to change $+0.9^{\circ}C$ in 2040s and $+4.0^{\circ}C$ in 2080s, and annual precipitation increased 9.6% in 2040s and 20.7% in 2080s respectively. The future watershed evapotranspiration increased up to 15.3% and the soil moisture decreased maximum 2.8% compared to baseline (2002~2010) condition. Under the future dam release condition of 9 years average (2002~2010) for each dam, the yearly dam inflow increased maximum 21.1% for most period except autumn. By the decrease of dam inflow in future autumn, the future dam storage could not recover to the full water level at the end of the year by the present dam release pattern. For the future flood and drought years, the temporal variation of dam storage became more unstable as it needs careful downward and upward management of dam storage respectively. Thus it is necessary to adjust the dam release pattern for climate change adaptation.

• Korean Journal of Ichthyology
• /
• v.21 no.1
• /
• pp.1-6
• /
• 2009

The effect of water temperature on fasting and post-prandial total ammonia excretion (TAN) of the starry flounder Platichthys stellatus (mean body weigh : $42.4{\pm}3.4g$) was studied. The fasting and post-prandial TAN excretions were measured under three different water temperatures (10, 15 and $20^{\circ}C$) for 24 hours using a recirculating system. In each treatment three replicates were set up and total 45 fish were used. Fish were taken to the indoor aquarium, acclimated over 10 days at three temperatures, and transferred to TAN measuring system for measurements of TAN excretion at the same temperatures. After 3 days of starvation, fasting TAN excretion was measured at each temperature. To investigate post-prandial TAN excretion, fish were hand-fed to satiation level with a commercial diet containing 50.2% crude protein for 7 days, two times daily 08 : 00 and 16 : 00 h. The fasting and postprandial TAN excretion increased with increased water temperature (p<0.05). Mean fasting TAN excretion rates at 10, 15 and $20^{\circ}C$ were 10.9, 11.2 and $12.2mg\;TAN\;kg\;fish^{-1}\;h^{-1}$, respectively. The value at $20^{\circ}C$ was higher than those at 10 and $15^{\circ}C$ (p<0.05), but there was no significant difference between $10^{\circ}C$ and $15^{\circ}C$. Mean post-prandial TAN excretion rates at 10, 15 and $20^{\circ}C$ were 33.0, 43.4 and $55.3mg\;TAN\;kg\;fish^{-1}\;h^{-1}$, respectively. Two peaks of post-prandial TAN excretions were observed, and the second peak was always greater than the first. The post-prandial TAN excretion rate reached to the maximum after 10 hours from the first feeding at $10^{\circ}C$($45.3mg\;TAN\;kg\;fish^{-1}\;h^{-1}$), $15^{\circ}C$ ($64.5mg\;TAN\;kg\;fish^{-1}\;h^{-1}$) and $20^{\circ}C$ ($83.2mg\;TAN\;kg\;fish^{-1}\;h^{-1}$), respectively. The TAN loss for ingested nitrogen at $20^{\circ}C$ (48.8%) was higher than that for $10^{\circ}C$ (43.0%) and $15^{\circ}C$ (45.7%). This study provides empirical data for estimating ammonia excretion and managing culture management of starry flounder under given temperatures.

• Journal of Intelligence and Information Systems
• /
• v.27 no.4
• /
• pp.23-48
• /
• 2021

The Korean economy has achieved continuous economic growth for the past several decades thanks to the government's export strategy policy. This increase in exports is playing a leading role in driving Korea's economic growth by improving economic efficiency, creating jobs, and promoting technology development. Traditionally, the main factors affecting Korea's exports can be found from two perspectives: economic factors and industrial structural factors. First, economic factors are related to exchange rates and global economic fluctuations. The impact of the exchange rate on Korea's exports depends on the exchange rate level and exchange rate volatility. Global economic fluctuations affect global import demand, which is an absolute factor influencing Korea's exports. Second, industrial structural factors are unique characteristics that occur depending on industries or products, such as slow international division of labor, increased domestic substitution of certain imported goods by China, and changes in overseas production patterns of major export industries. Looking at the most recent studies related to global exchanges, several literatures show the importance of cultural aspects as well as economic and industrial structural factors. Therefore, this study attempted to develop a forecasting model by considering cultural factors along with economic and industrial structural factors in calculating the import volume of each country from Korea. In particular, this study approaches the influence of cultural factors on imports of Korean products from the perspective of PUSH-PULL framework. The PUSH dimension is a perspective that Korea develops and actively promotes its own brand and can be defined as the degree of interest in each country for Korean brands represented by K-POP, K-FOOD, and K-CULTURE. In addition, the PULL dimension is a perspective centered on the cultural and psychological characteristics of the people of each country. This can be defined as how much they are inclined to accept Korean Flow as each country's cultural code represented by the country's governance system, masculinity, risk avoidance, and short-term/long-term orientation. The unique feature of this study is that the proposed final prediction model can be selected based on Design Principles. The design principles we presented are as follows. 1) A model was developed to reflect interest in Korea and cultural characteristics through newly added data sources. 2) It was designed in a practical and convenient way so that the forecast value can be immediately recalled by inputting changes in economic factors, item code and country code. 3) In order to derive theoretically meaningful results, an algorithm was selected that can interpret the relationship between the input and the target variable. This study can suggest meaningful implications from the technical, economic and policy aspects, and is expected to make a meaningful contribution to the export support strategies of small and medium-sized enterprises by using the import forecasting model.

• Journal of Korean Home Economics Education Association
• /
• v.33 no.1
• /
• pp.129-149
• /
• 2021

The purposes of this study were to examine the current status of the establishment of home economics-related departments in colleges and universities and the changes required in the home economics curriculum of secondary schools, and to structure the elective courses of home economics subject(group) that can be organized in the next high school curriculum. To achieve these purposes, related literature and data were analyzed, and a questionnaire survey and FGI were conducted by home economics experts. The research results are as follows. First, home economics was considered to be highly related not only to the human ecology but also to social sciences, education, engineering, and arts and physical education. The numbers of technical colleges and 4-year universities with departments related to home economics were 1,405 and 961 respectively in 2019. Therefore, it was confirmed that there is a sufficient basis for opening home economics subject(group) elective courses in high school. Second, in the secondary school home economics curriculum, the concepts of culture, relations, independence, and sustainability were emphasized based on the changing life patterns and values. It was proposed that the contents of the home economics course would be structured in a way that allows deep and high-level thinking and helps students to enjoy culture. This demand can be implemented by diversifying, specializing, and structuring the elective courses of the home economics subject(group). Third, a total of 18 elective subjects and subject outlines were structured in the fields of child/family, food/nutrition, clothing, housing, consumption/family management, and home economics integration. This study results will contribute to the establishment of the high school credit system by providing basic information for organizing the next home economics curriculum, and expanding the options for home economics subject(group) to high school students.

• Journal of International Area Studies (JIAS)
• /
• v.14 no.2
• /
• pp.499-524
• /
• 2010

The purpose of this study is to based on review of theoretical and empirical studies to assess the independence of central banks - the former Socialist republics, including the Russian Federation and Czech, Poland. In addition, the work is expected to clarify whether a link exists between independence and the most important economic indicators such as inflation, economic activity, the budget deficit. And The subject of this study are the formal and actual independence of national banks, as well as limiting factors: political and economic. Background investigation of the problem of independence of central banks from the fact that, according to many economists, it is essential to the successful development of a market economy. The effectiveness of any country's economy due to currency volatility, low inflation, high reliability of the banking system, etc. As far as the independence of monetary regulation contributes to these goals - one of the most actively debated issues in the world of economic theory and practice for a long time. The issue of central bank independence is extremely important for Russia, Czech, Poland. In the near future to the central bank has important tasks, among which are the transition to inflation targeting in the rejection of significant intervention in the foreign exchange market, as well as improving the sustainability of the national banking system. Transparency and independence of the Bank of Russia, Czech Republic, Poland, in my view, should be an important factor in achieving these goals. The countries of Czech Republic, Poland have already made a number of steps to bring the status of their banks to the European standards. Many other developing countries are also in the process of reforming their central banks and the improving conditions of their functioning. However, despite the fact that as a model for reform used by the central banks of countries with developed market economies, central banks in developing countries are still yet deprived of the legal, economic and political independence. A different situation exists in transition space. Because of significant differences in the views of the authorities in transition republics at the necessary level of independence of central banks and the exchange rate and monetary policy reform of monetary management in these countries led to different results.

• Journal of Venture Innovation
• /
• v.5 no.4
• /
• pp.109-115
• /
• 2022

As the 4th industrial revolution progresses, foreign countries are promoting smart manufacturing innovation through digital transformation as a priority task early on to secure a competitive edge in the manufacturing industry. In response, the Korean government is also promoting a policy to enhance the competitiveness of small and medium-sized manufacturing companies by promoting digital transformation in the corporate sector to meet the global trend of the 4th industrial revolution era. Manufacturing powerhouses such as Germany and Japan see manufacturing as a key sector in digital transformation and are leading related policies, while emerging countries such as China are also promoting manufacturing innovation strategies such as building digital infrastructure and creating a digital innovation ecosystem. Korea is promoting the 'Korean-style smart factory dissemination and expansion strategy' by transforming Germany's manufacturing innovation strategy for smart factory supply to suit the domestic situation. However, the policy to supply smart factories so far has been conducted with support from individual companies under the leadership of the government, and most of the smart factories are at the basic level, and it is evaluated that there are limitations such as the lack of manpower to operate smart factories. In addition, while the current policy focuses on expanding the supply of smart factories in SMEs, it is necessary to establish a smart manufacturing system through linkages between large and small businesses in order to achieve the original goal of establishing a smart manufacturing system. Therefore, it can be said that from the standpoint of small and medium-sized enterprises (SMEs), who are consumers of smart factories, it can be said that the digital transformation policy can achieve the expected results only when appropriate incentives are provided for the introduction of smart factories in a situation where management resources such as funds, technology, and human resources are lacking. In addition, it is judged that the uncertainty of the performance of digital investment always exists, and as long as large and small companies are maintained as an ecosystem of delivery and subcontracting, there is very little incentive for small and medium-sized manufacturing companies to voluntarily invest in or advance digital transformation. Therefore, the digital transformation policy of small and medium-sized manufacturing companies in the future has practical significance in that it suggests that there is a need to seek ways to attract SMEs' digital-related voluntary investment.