• Proceedings of the KSR Conference
• /
• 2007.11a
• /
• pp.1946-1950
• /
• 2007

Switch rail is a very important part on the railway track, which not only accounts for the safety of the passing trains but also greatly influences the speed of the train. The higher the speed and the loads of the train the more it demands on the properties of the switch rail. Research shows that the higher mechanical properties of switch rail the longer the service life. Induction heat treatment is a good way of improving the mechanical properties of metallic materials. But the switch rail's section area changes gradually across the lengthways, which is difficult for induction heating especially for the small section. And the mechanical property of small section of the switch rail is the most important for its service life. The induction heat treatment used past always brings the low hardness on small section which can cause low service life of switch for wearing, or too high hardness because of martensite microstructure which can cause the shelling or even breaking of the switch rail. To prolong the service life of switch rail by higher mechanical properties, we researched the improved induction heat treatment for switch rail by adjusting speed of heating, and adopting compressed air cooling. The results showed that switch rail obtain almost the same high hardness across the length way after the improved induction heat treatment, which is very helpful to extend the service life of switch rail.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2007.06a
• /
• pp.599-600
• /
• 2007

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.27 no.1
• /
• pp.61-67
• /
• 2013

The turnout point system is installed to separate the main rail track from other tracks in rail load stations. It is also important to set up the switch point system to change the direction of the turnout point, to lead and change the direction of tracks. The switch point system can be negatively affected by heavy snow during winter seasons which can cause critical safety problems. Furthermore, the maintenance and repair of the conventional system is prohibitively expensive due to its complexity and high probability of failure. In this paper, an efficient switch point system is proposed which simplifies the equipment structure and lowers the cost for maintenance and repair, while improving safety and performance of the rail road system.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2005.06a
• /
• pp.1644-1647
• /
• 2005

This study was aimed at evaluating the structural safety for rubber tired AGT system. Based on these, AGT system which was developed for first time in domestic is need to verify structural safety. So we measured the characteristics of guide-rail, switch rail, side wall in the constructed test track for rubber tired AGT system. Finally, all results of test showed that structural safety of the rubber tired AGT system.

• Proceedings of the KSR Conference
• /
• 2010.06a
• /
• pp.1663-1668
• /
• 2010

The terms of track is a train-only line for a train service, in premises of station of a station, that the unit over the track for turnout the track from one track to another track, which it changes the course from the main track that is used for operating a train to the side track, is called a turnout The stick strength of tongue rail is adjusting uniform pressure on the both sides, the adhesion strength between a basic rail and tongue rail has to maintain over 100kg of power value to open over 1mm the ends. This study suggested developing a measuring instrument that can measure a basic rail and the stick strength of a movable rail in according with a switch, such as a switch point, and a performance test. This study ties to be helped that it improves measuring usability for the maintainers through improving quality in a stick measuring instrument, that it solves a technique in the site difficulties through improving a measuring instrument, with reducing the obstacles and expenses.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.59 no.2
• /
• pp.355-358
• /
• 2010

As CMOS technology continues to scale down, signal processing is favorably done in the digital domain, which requires Analog-to-Digital (A/D) Converter to be integrated on-chip. This paper presents a design methodology of 12-bit 1-MS/s Rail-to-Rail fully differential SAR ADC using Deep N-well Switch based on binary search algorithm. Proposed A/D Converter has the following architecture and techniques. Firstly, chip size and power consumption is reduced due to split capacitor array architecture and charge recycling method. Secondly, fully differential architecture is used to reduce noise between the digital part and converters. Finally, to reduce the mismatch effect and noise error, the circuit is designed to be available for Rail-to-Rail input range using simple Deep N-well switch. The A/D Converter fabricated in a TSMC 0.18um 1P6M CMOS technology and has a Signal-to-Noise-and-Distortion-Ratio(SNDR) of 69 dB and Free-Dynamic-Range (SFDR) of 73 dB. The occupied active area is $0.6mm^2$.

• Journal of Environmental Impact Assessment
• /
• v.15 no.6
• /
• pp.453-458
• /
• 2006

A turnout system which permits trains to pass from one track to another consists of the switch, the crossing, lead rails which are necessary to connect the switch and the crossing, two guard rails and a switch machine for operating the switch. A turnout is the sole moving part among the railway components and has complex configuration, so the safety has always been raised an issue. In Korea, it is planned to adopt the high speed tilting train, which operates at the maximum speed of 180km/h, at conventional lines by the year of 2010. However, for the application of the tilting train to conventional lines, it is prerequisite to establish a stable turnout system allowing the tilting train to pass through it without reducing speed. Therefore, the improved turnout system for the speed-up of conventional lines has been developed and the prototype of the turnout system has been constructed. In this study, evaluation of noise characteristics around the improved turnout system was performed through the field measurements. Field measurements of noise around the conventional and the high-speed turnout system were also carried out for the comparison.

• Proceedings of the KSR Conference
• /
• 2010.06a
• /
• pp.549-556
• /
• 2010

Reliable fast working maglev switch is one of the key technologies needed for the maglev system to be commercialized. Switch for the maglev system is large, heavy, complicated, expensive compared with that of the traditional wheel-on-rail system. This paper reports the development of a segmented maglev switch for urban transit maglev system under construction for the 6.1 km long double track maglev commercialization line in Inchon international airport in 2012. Test results along with details of the segmented maglev switch components are reported.

• Proceedings of the KSR Conference
• /
• 2011.05a
• /
• pp.1742-1749
• /
• 2011

The 3 way segmented Maglev switch is developed for the urban Maglev vehicle, which is scheduled to debut at the middle of 2013 in Incheon International Airport. The 3 way switch is composed of 3 moving girders, 4 fixed girders, driving units, moving units, clamping units and articulated angle relieving equipment etc. In this paper, the measured results on the interaction between vehicle and switch are discussed. The measured results are following; First, continuous moving test and natural frequency for girder and levitation rail. Second, levitation and lateral air gap of the bogies running on the curved switch. Third, noise of moving mechanical parts of the 3 way segmented switch. Forth, thermal displacement of the girder due to temperature change. With over the measured results, more reliability and stability of the 3 way segmented switch are secured.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2012.10a
• /
• pp.985-986
• /
• 2012