• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2005년도 추계학술대회 논문집 Vol.18
• /
• pp.155-156
• /
• 2005

We investigated the quench characteristics of the flux-lock type superconducting fault current limiter (SFCL) integrated three-phase according to fault types such as the single-line-to-ground fault, the double-line-to-ground fault and the three-line-to-ground. The structure of integrated three-phase flux-lock type SFCL consists of single core which have three-phase flux-lock reactors. The superconducting elements connected sound phase as well as fault phase happened to quenching. Therefore we conformed that the superconducting elements were dependent.

• Rapid Communication in Photoscience
• /
• 제4권1호
• /
• pp.25-28
• /
• 2015

The time-resolved photoexcitation dynamics of electrical conductivity of the magnetic organic superconductor ${\lambda}-(BETS)_2Fe_{0.45}Ga_{0.55}Cl_4$ has been studied with a nanosecond visible laser pulse at its three different phases, i. e., metallic phase, superconducting phase and insulating phase. A transient increase of the resistance is induced by photoirradiation at all the temperatures measured for all three phases, but the decay profile shows a significant temperature dependence. The relaxation rate in the metallic and insulating phase are different from each other, and the decay time is relatively faster and almost constant in the metallic phase. However, a prolongation of the relaxation time is observed at temperature just around the narrow superconducting phase. Nonbolometric (nonthermal) origin of the observed photoresponse of the electrical conductivity is confirmed in the superconducting phase.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2005년도 추계학술발표대회 개요집
• /
• pp.262-264
• /
• 2005

$Bi_{2}Sr_{2}CaCu_{2}O_{x}$(Bi-2212) and $Bi_{2}Sr_{2}Ca_{2}Cu_{3}O_{y}$(Bi-2223) high-$T_{c}$ superconductor(HTS) coating have been prepared by plasma spraying and heaat treatment. The Bi-2212 HTS coating later is synthesized through the peritectic reaction between Sr-Ca-Cu oxide coating layer and Bi-Cu oxide coating later, and $Bi_{2}Sr_{2}CaCu_{2}O_{y}$(Bi-2212) superconducting phase grow by partial melting process. The superconducting characteristic depends strongly on the conditions of the partial melting process. the Bi-2212 HTS layer consists of the whiskers grown in the diffusion direction. Above the 2212 layer, Bi-2223 phase and secondary phase was observed. The secondary phase is distributed uniformly over the whole surface. This is caused to the microcrack on the coatings surface. Despite everything, the film shows superconducting with an onset $T_{c}$ of about 115K. There are two changes steps. One changes (1step) at 115K is due to the diamagnetism of the Bi-2223 phase and the other changes (2step) at 78K is due to the diamagnetism of the Bi-2212 phase.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1998년도 하계학술대회 논문집 A
• /
• pp.94-97
• /
• 1998

The conceptual design of integrated three phase superconducting fault current limiter (SFCL) is presented. And through simulation of power system where this SFCL is installed, the characteristics of this SFCL is analyzed. It is like three-phase transformer. So it has the same characteristics with inductive single phase SFCL. But it has more merits than single phase SFCL. Differently to single phase SFCL, integrated three phase SFCL induces impedance at all phase by any single phase fault to protect the power system more safely.

• 한국초전도ㆍ저온공학회논문지
• /
• 제6권1호
• /
• pp.1-5
• /
• 2004

Long length of Bi-2223/Ag superconducting wives were fabricated by stacking and drawing process with advanced heat-treatment schedules. Intermediate annealing was carried out to increase the homogeneity and uniformity of the superconducting filaments embedded in the silver matrix. Phase modification from tetragonal to orthorhombic Bi-2212 by pre heat treatment(PHT) was executed to improve the texture and phase transformation of Bi-2223. Drawing stress was measured to predict the sausaging and stress limit. Rolling Parameters such as thickness. width and winding tension were investigated to roll the tape with uniformity. 1 km length of Bi-2223/Ag superconducting wires were fabricated without any breakage. Critical current (Je) of 270 m length of superconducting tapes was measured over than $70 A/cm^2$ continuously after final sintering.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2003년도 하계학술대회 논문집 Vol.4 No.2
• /
• pp.1204-1207
• /
• 2003

BiSrCaCuO superconducting thin films have been fabricated by co-deposition using IBS(ion Beam Sputtering) method. Despite setting the composition of thin film Bi2212 or Bi2223, in both cases, Bi2201, Bi2212 and Bi2223 phase were appeared. It was confirmed the obtained field of stabilizing phase was represented in the diagonal direction of the right below end in the Arrhenius plot of temperature of the substrate and $PO_3$, and it was distributed in the rezone.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2005년도 춘계학술대회 논문집
• /
• pp.94-97
• /
• 2005

Bismuth high Tc superconducting thin films are fabricated via a co-deposition process by an ion beam sputtering with an ultra low growth rate, and sticking processing of the respective elements are evaluated. The sticking processing of bismuth element in bismuth high Tc superconducting thin film formation was observed to show a unique temperature dependence; it was almost a constant value of 0.49 below about $730^{\circ}C$ and decreased linearly over about $730^{\circ}C$. This temperature dependence can be elucidated from the evaporation and sublimation rates of bismuth oxide, $Bi_2O_3$, from the film surface. It is considered that the liquid phase of the bismuth oxide plays an important role in the bismuth phase formation in the co-deposition process.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2003년도 하계학술대회 논문집 B
• /
• pp.958-960
• /
• 2003

Although the researches and developments are performed for superconducting technologies, many problems such as AC loss and quench phenomenon still remain to design the superconducting transformer. In addition, pre-study on the three phase high temperature superconducting (HTS) transformer is a sort of time and expense consuming work, thus it is very worthy of being analyzing the characteristics of HTS transformer in advance through proper simulation programs and skills. This paper presents an effective simulation method for the three phase HTS transformer using components developed in the PSCAD/EMTDC.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2007년도 하계학술대회 논문집 Vol.8
• /
• pp.484-485
• /
• 2007

BiSrCaCuO superconducting thin films have been fabricated by co-deposition using the faraday cup. Despite setting the composition of thin film Bi2212, Bi(2201, 2212, 2223) phase were appeared. It was confirmed the obtained field of stabilizing phase was represented in the diagonal direction of the right below end in the Arrhenius plot of temperature of the substrate and $PO_3$, and it was distributed in the rezone.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 1993년도 추계학술대회 논문집
• /
• pp.43-46
• /
• 1993

Superconducting cable (Ic: 60 A at 77K. 10 filaments) with Bi high-Tc superconducting system was developed by powder - in - tube method. Pressing and sintering process of the cables were repeated for growth of 2223 high-Tc superconducting phase. The cable can be fabricate by twist method that is nessary for high current density and cooled circulative system. This cab1e system can be used for commercial.