• Korean Journal of Materials Research
• /
• v.1 no.4
• /
• pp.177-183
• /
• 1991

Change of the properties of selective CVD-W by $SiH_4$ reduction with the variation of deposition time and pressure has been investigated. The lime required for covering the who)to Si substrate by tungsten at $300^{\circ}C$ under the pressure of 100mtorr is approximately 30 seconds. The film thickness tends to increase linearly in the early stage of deposition process and parabolically later, sheer resistance of the film tends to decrease rapidly initially, and slowly later with deposition time. Tungsten grain size does not change much, but grain boundary becomes hazy in the pressure range of 50-300mtorr. Also no ${\beta}-W$ but only ${\alpha}-W$ was found in this pressure range. The deposition rate and electrical resistivity of tungsten tend to increase wish increasing pressure. The results of AES analysis show that pressure does not much affect Si/W ratio of the tungsten film and silicidation at the W/Si interface.

• Korean Journal of Materials Research
• /
• v.10 no.8
• /
• pp.525-531
• /
• 2000

Sb-doped tin oxide films were deposited on Cornig glass 1737 substrate by plasma enhanced chemical vapor deposition (PECVD) technique. The films deposited at different reaction parameters were then examined by using XRD and AFM. The relatively good crystalline thin film was formed at $450^{\circ}C$, input gas ratio R[$P_{SbCl}P_{{SnCl}_4}$]=1.12 and r.f. power 30W. The surface roughness of the film formed by PECVD compared to TCVD was more smooth. Higher concentration of Sb dopant, lower deposition temperature, and thinner thickness of deposited film led to de-creasing surface roughness of the formed thin films.

• Journal of Sensor Science and Technology
• /
• v.11 no.1
• /
• pp.1-8
• /
• 2002

In this paper, a thermopile which is applied to wide uses of temperature measuring was fabricated and its characteristic was improved by appling SOI structure to the fabrication. We improved characteristic of the thermopile by using single crystal silicon strips that has high seebeck coefficient and dielectric isolating the silicon strips from substrate with silicon dioxide film which dramatically decrease thermal conductivity between hot and cold junction compared to a silicon strip which was fabricated by ion implantation. The thermopile consists of 17 p-type single crystal silicon strips and 17 n-types by serial connection. The result of electromotive force measuring showed very good characteristic as 130mV/K when temperature difference between the two ends of the thermopile occurs by applying light on the thermopile fabricated with silicon strips of $1600{\mu}m$ length, $40{\mu}m$ width, $1{\mu}m$ thickness.

• Journal of Sensor Science and Technology
• /
• v.11 no.1
• /
• pp.54-59
• /
• 2002

This paper describes a new process technique for batch process of SOI(Si-on-Insulator) structures with buried cavities for MEMS(Micro Electro Mechanical System) applications by SDB(Si-wafer Direct Bonding) technology and electrochemical etch-stop. A low-cost electrochemical etch-stop method is used to control accurately the thickness of SOI. The cavities were made on the upper handling wafer by Si anisotropic etching. Two wafers are bonded with an intermediate insulating oxide layer. After high-temperature annealing($1000^{\circ}C$, 60 min), the SDB SOI structure with buried cavities was thinned by electrochemical etch-stop. The surface of the fabricated SDB SOI structure have more roughness that of lapping and polishing by mechanical method. This SDB SOI structure with buried cavities will provide a powerful and versatile substrate for novel microsensors arid microactuators.

• Applied Microscopy
• /
• v.36 no.3
• /
• pp.155-163
• /
• 2006

The defects in a synthesized crystal of ${\alpha}-Al_2O_3$ used as substrate for growing of semi-conductor materials such as GaN were examined by the conventional transmission electron microscopy (TEM), Large Angle CBED and High-Angle Annular Dark Field (HAADF) STEM methods. The dominant defects found in the specimen are basal microtwins with the thickness of ${\sim}2\;to\;32 nm$ and the associated strong strain field at the interface of microtwin/matrix, basal dislocations and complex dislocations in the one of {$2\bar{1}\bar{1}3$} pyramidal slip plane. All these basal and pyramidal dislocations seem to be strong related to basal microtwins. It was also found that the density of defects is very uneven. In the certain area with the dimension of a few fm, the dislocation density is quite high as an order of ${/sim}10^{10}/cm^2, but the average density is roughly estimated to be less than ${\sim}10^5/cm^2, as is usually expected in general synthesized crystals.

• Laser Solutions
• /
• v.17 no.1
• /
• pp.1-6
• /
• 2014

Indium tin oxide (ITO) is an important transparent conducting oxide (TCO). ITO films have been widely used as transparent electrodes in optoelectronic devices such as organic light-emitting devices (OLED) because of their high electrical conductivity and high transmission in the visible wavelength. Finding ways to control ITO micromachining depth is important role in the fabrication and assembly of display field. This study presented the depth control of ITO patterns on glass substrate using a femtosecond laser and slit. In the proposed approach, a gaussian beam was transformed into a quasi-flat top beam by slit. In addition, pattern of square type shaped by slit were fabricated on the surfaces of ITO films using femtosecond laser pulse irradiation, under 1030nm, single pulse. Using femtosecond laser and slit, we selectively controlled forming depth and removed the ITO thin films with thickness 145nm on glass substrates. In particular, we studied the effect of pulse number on the ablation of ITO. Clean removal of the ITO layer was observed when the 6 pulse number at $2.8TW/cm^2$. Furthermore, the morphologies and fabricated depth were characterized using a optical microscope, atomic force microscope (AFM), and energy dispersive X-ray spectroscopy (EDS).

• Journal of Sensor Science and Technology
• /
• v.11 no.3
• /
• pp.183-190
• /
• 2002

Photoluminescence(PL) properties of $Si^+$-implanted $SiO_2$ film, which was thermally grown on c-Si substrate, is reported. We have compared room temperature photoluminescence (PL) spectra of the samples which was made in several kinds of implantation, subsequent annealing and $SiO_2$ film thickness. XRD data was correlated with the PL spectra. Silicon nanocrystals in $SiO_2$ film is considered as the origin of the photoluminescence. PL spectra was investigated after wet etching of the $SiO_2$ film by using BOE (Buffered Oxide Etchant) at every one minute. PL peak wavelength was varied as the etching is proceeded. These results indicate that the quantity and the distribution of dominant size of Si nanocrystals in $SiO_2$ film seem to have a direct effect on PL spectrum.

• Journal of the Korean institute of surface engineering
• /
• v.44 no.5
• /
• pp.226-231
• /
• 2011

Graphene was coated on STS 316L by electro spray coating method to improve its properties of corrosion resistance and contact resistance. Exfoliated graphite (graphene) was made of the graphite by chemical treatment. Graphene is distributed using dispersing agent, and STS 316L was coated with diffuse graphene solution by electro spray coating method. The structure of the exfoliated graphite was analyzed using XRD and the coating layer of surface was analyzed by using SEM. Analysis showed that multi-layered graphite structure was destroyed and it was transformed into fine layers graphene structure. And the result of SEM analysis on the surface and the cross section, graphene layer was uniformly formed with 3~5 ${\mu}m$ thickness on the surface of substrate. Corrosion resistance test was applied in the corrosive solution which is similar to the PEM fuel cell stack inside. And interfacial contact resistance test was measured to simulate the internal operating conditions of PEM fuel cell stack. The results of measurements show that stainless steel coated with graphene was improved in corrosion resistance and surface contact resistance than stainless steel without graphene coating layer.

• Journal of the Korean Ceramic Society
• /
• v.41 no.1
• /
• pp.30-35
• /
• 2004

PMW-PZT thick films of about $30{\mu}m$ thickness were fabricated on Pt/$TiO_2$/$SiN_x$Si substrate by the hybrid method of screen printing and PZT sol application. With the increase of the number of the sol application times, the sintered density and electrical properties of PMW-PZT thick films were evidently increased. For the PMW-PZT thick film with PZT sol application of 10-times, the dielectric constant ($\varepsilon_r$) was 745 at the frequency of 100 KHz and thepiezoelectric coefficient ($d_33$) was 155 pC/N at the applied pressure of 1 atm.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.18 no.3 s.118
• /
• pp.298-304
• /
• 2007

In this paper, the antenna which has a multiband operation (GSM850, EGSM, DCS1800, USPCS, W-CDMA) is proposed. This antenna was designed by the commercial software HFSS 3-D EM simulator, and it is organized by using a meander branch structure which has a via and lines on FR-4$(\varepsilon_r=4.4)$ substrate. Especially, it has a gap feeding structure which makes good operation at overall bandwidth. The designed antenna is manufactured by PCB processing, and measured by using a network analyzer and a test chamber. The manufactured antenna with the dimension of 8 mm width, 20 mm height and 3.2 mm thickness is able to applied as an internal antenna for multiband mobile phones.