• Journal of the Korean Institute of Telematics and Electronics
• /
• v.9 no.2
• /
• pp.1-16
• /
• 1972

In this paper, the characteristics of linearly tapered strip-line filters, where the even-mode and odd-mode characteristic impedances vary linearly with the same degree along the lines, are analyzed. The Impedance parameters of linearly tapered coupled strip-line, which is made by connecting two linearly tapered unsymmetric coupled strip-lines In cascade and the I:no input and output terminals are made equal, are obtained. Using the above parameters, the Image parameters of linearly tapered coupled strip-line filters are derived. The result of analysis shows that the line length can be made shorter and also the stop-band width between the fundamental and second pass-band becomes wider, compared with the coupled strip-line filters which use uniform strip-lines. Furthermore, the difference of impedance levels in the fundsmental and second pass-band becomes larger with the degree of taper of the lines. This property is unique, in comparison with the case of uniform or exponentially tapered strip-line filters.

• Journal of the Korean Society for Precision Engineering
• /
• v.12 no.5
• /
• pp.69-76
• /
• 1995

This paper describes characteristics of EDT(Electro Discharge Texturing) and that the strip surface has influence on the paintability. The pulse mode and the capacitor mode of recently developed EDT method were investigated about the peak shape and the roughness of strip surface. And EDT method compared the above-mentioned contents with the SBT(Shot Blast Texturing) method. The peak count of the pulse mode is more than that of the capacitor mode. But the lower roughness below the Ra 3.2 .mu. m of the strip surface, the texturing time of the pulse mode is longer than the capacitor mode. In SBT method, the peak shape is similar to capacitor mode. But the EDT roll has more uniformity than the SBT roll and has more peak count than that of SBT roll. Therefore, in the painted steel sheet, EDT roll gives better surface of clarity image than the SBT roll.

• 제어로봇시스템학회:학술대회논문집
• /
• 1996.10a
• /
• pp.319-323
• /
• 1996

A new steel-making process, strip-casting, is introduced. The strip-casting is a new technique making the thin steel strip from the molten steel directly without resorting to repetitive reheating and hot-rolling required in a conventional steel-making method. This paper derives the mathematical model of strip caster, proposes a control strategy for stable startup operation and a fuzzy decision making rule for automatic control mode change in strip-casting process.

• Aerospace Engineering and Technology
• /
• v.3 no.2
• /
• pp.34-41
• /
• 2004

In this paper, the SAR operational mode for achieving mission is designed. Each mode, which is the strip mode, scan mode, and fine mode, is basically considered. Based on the characteristics, which includes incidence angle, of the topography in Korean Peninsula, look angle for SAR satellite is determined. The limited region of operating the mission, which is considered to be able to receive and transmit the radar data, was defined to use determined operational mode. In the future, as considering full requirements and conditions for the SAR satellite, requirements and parameters will be discussed and studied.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.19 no.2
• /
• pp.331-337
• /
• 1994

The scatting problem by E-polarized plane wave with obique incidence on a tapered resistive strip grating with zero resistivity(perfectly conducting) at strip-edges is analyzed by the method of moments in the spectral domain. Then the induced surface current density on the strip is expanded in a series of Chebyshev polynomials of the second kind. The expasion coefficients are calculated numerically in the spectral domain, the numerical results of the geometric-optical reflection coefficient for the tapered resistivity in this paper are compared with those for the existing uniform resistivity. And the position of sharp variation points in the magnitude of the geometric-optical reflection coefficient can be moved by varying the incident angle and the strip spacing, It is found out that these sparp variation points are due to the transition of higher mode between the propagation mode and the evanescent mode.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.31A no.2
• /
• pp.60-66
• /
• 1994

The scattering problem by E-polarized plane wave with oblique incidence on a tapered resistive strip grating with infinite resistivity at strip-edges is analyzed by the method of moments in the spectral domain. Then the induced surface current density is expanded in a series of Ultraspherical polynomials of the zeroth order. The expansion coefficients are calculated numerically in the spectral domain, the numerical results of the geometricoptical reflection coefficient for the tapered resistivity in this paper are compared with those for the existing uniform resistivity. And the position of sharp variation points in the magnitude of the geometric-optical reflection coefficient can be moved by varying the incident angle and the strip spacing. It is found out that these sharp variation points are due to the transition of higher modes between the propagation mode and the evanescent mode.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.29 no.2
• /
• pp.93-97
• /
• 2009

An advantage of a magnetostrictive strip transducer for a long-range guided wave inspection is that the wave patterns are relatively clear and simple when compared to a conventional piezoelectric ultrasonic transducer. Therefore, if we can characterize the evolution of defect signals, it could be a promising tool for a structural health monitoring of pipes for a long period of time as well as an identification of flaws. However, when evaluating a signal during a realistic field examination, it should be careful because of some spurious signals or false indications, such as signals due to a directionality, multiple reflections, mode conversion, geometrical reflections etc. Mode converted signals from a realistic piping mockup were acquired and analysed. We found mode conversions between a torsional guided wave T(0,1) mode and a flexural F(1,3) or longitudinal L(0,2) mode generated by a magnetostrictive strip transducer. Based on the experimental observations, an interpretation of the source of the mode conversion is discussed in a viewpoint of electromagnetic properties and structure of the strip transducer.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 1999.08a
• /
• pp.27-36
• /
• 1999

To have high flatness quality of hot rolled strip in the hot strip finishing mill train, a new inter-stand tension profile measuring device of segmented looper roll type(coined as Flatness Sensing Inter-stand Looper, FlatSIL) and a new flatness control system have been developed in this study. The device measures the strip tension profile across the strip width and informs the strip wave pattern to new flatness control system where work roll bending mode to relieve the strip wave is determined. The existing automatic shape control system which uses laser type shape-meter installed at the outlet of the last finishing mill stand strip tension between down coiler and last finishig mill since the latent wave concealed by the strip tension between down coiler and last finishing mill stand cannot be measured by the laser distance-meter. Thus the existing shape control system is not able to control the flatness through the full strip length. The new flatness control system, however, works for full strip length during strip rolling as far as the tension profile measuring device and work roll bender are on. With the new flatness control system, work roll bender is automatically controller to minimize the latent wave of the running strip and the flatness quality as well as strip travelling stability has been noticeably improved from strip head through body to tail.

• Proceedings of the Korea Electromagnetic Engineering Society Conference
• /
• 2000.11a
• /
• pp.399-403
• /
• 2000

A new type of collinear antenna called short-ended coaxial slot-coupled strip array antenna is investigated theoretically. The antenna has an advantage of structural simplicity. The integral equations are derived for the proposed structure by use of the Fourier transform and mode expansion, and the simultaneous linear equations are obtained. The slot electric field and strip current are then obtained by solving the simultaneous linear equation. The effects of slot and strip number on the radiation efficienty, beamwidth and directivity gain are also presented.

• 제어로봇시스템학회:학술대회논문집
• /
• 2001.10a
• /
• pp.68.3-68
• /
• 2001

We describe the looper controller design for a hot strip mill. The looper is to control the strip tension which influences on the width of the strip. It is very important to control the looper control of the hot strip mill, but difficult to control the looper, because there exists mutual interaction among strip gauge, looper angle, and strip tension. In this paper, we present the modeling for the looper of a hot strip mill to control the tension of the strip and suggest a eigenstructure assignment method. The eigenstructure assignment is useful tool that allows the designer to satisfy damping, settling time, and mode decoupling specifications directly by choosing eigenvalue and eigenvectors. Desired eigenvalue and eigenvector are chosen to satisfy the desired responses.