• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2008년도 춘계 학술발표회 제20권1호
• /
• pp.933-936
• /
• 2008

모르타르에 2 %이내의 합성섬유를 혼입함으로써 콘크리트의 수십, 수백 배에 달하는 인장변형률 경화거동을 보이는 ECC가 기존 연구에 의해 개발되었으며, ECC를 구조부재에 사용할 경우, 구조물의 성능개선이 매우 커질 것으로 판단된다. 그러나 ECC를 사용한 구조물을 설계할 때 중요한 요인인 ECC의 인장거동 관계 예측에 대해서는 많은 연구가 이루어지지 않았으며, 특히 보다 실제적인 인장거동 관계를 예측하기 위해서는 섬유분산성 등 실제의 균열면응력-변위 곡선을 고려한 연구가 필요하다. 따라서, 이 연구에서는 ECC의 인장거동 관계를 예측할 수 있는 기법을 제시하였다. ECC의 인장거동 예측방법은 초기균열강도, 인장강도, 인장변형률을 구하는 과정으로 구성되는데, 보다 합리적이고 실제적인 ECC의 인장거동 예측을 위하여 균열면응력에서 가교작용에 기여하는 유효섬유의 개수를 섬유의 기울어진 각도와 섬유사이의 간격에 따라 예측하였다. 또한 극한인장변형률 예측을 위하여 화상처리기법을 사용하였다. ECC의 인장실험결과와의 비교를 통하여 예측방법의 타당성을 평가하였다.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2007년 가을학술발표회
• /
• pp.334-344
• /
• 2007

This paper performed a comprehensive evaluation of the results of the 2007 Ground Response Analysis Round Robin Test, at which 14 institutions and individuals participated. The submitted results showed significant discrepancies. The main reason for this difference has been attributed to the dispersion in the estimated shear wave velocity profiles and dynamic soil curves. It is therefore concluded that accurate evaluation of the material properties is of primary importance for reliable estimation of the ground vibration. Evaluation of the effect of the analysis method showed that the equivalent linear analysis overestimates the peak ground acceleration, but overall the results are similar to a total stress nonlinear analysis. However, the total and effective stress nonlinear analyses show distinct discrepancies, the effective stress analyses consistently resulting in a lower response due to the development of the excess pore water pressure and thus softer response.

• 지구물리와물리탐사
• /
• 제5권2호
• /
• pp.99-107
• /
• 2002

표면파 기법(SASW, Spectral Analysis of Surface Waves)을 지반공학 분야에 효율적으로 적용하기 위해 모형 응답 알고리듬을 해석적으로 도출하였다. 이 논문에서는 이론적인 분산 곡선 응답 반응을 Aki and Richard에 의해 제안된 운동 응력 벡터(motion stress vector)를 이용하여 미분 방정식을 구성한 후 차분 전개를 통하여 구함으로서 동적 강성도 법이나 전파 행렬법에 비해 간단하고 빠르게 구할 수 있었다. 차분 전개를 통한 이론 분산 곡선 응답 반응 알고리즘으로 2개의 지구 모형에 대해 이론 분산 곡선을 구하여 타당성을 검증하였다. 또한 모형 응답 계산 과정에서 고려하여야 할 주파수 대역에 따른 적절한 모형의 크기에 대하여 고찰한 결과 각 파장의 $1.5\~2$배 이내로 모형의 크기를 결정할 때 경제적이고 안정적인 결과를 얻을 수 있었다.

• Nuclear Engineering and Technology
• /
• 제53권11호
• /
• pp.3723-3740
• /
• 2021

The harsh conditions in the reactor affect the thermal and mechanical performance of the fuel plate heavily. Some in-pile behaviors, like fission-induced swelling, can cause a large deformation of fuel plate at very high burnup, which may even disturb the flow of coolant. In this research, the emphasis is put on the thermal expansion, fission-induced swelling, interaction layer (IL) growth, creep of the fuel meat, and plasticity of the cladding for the U₃Si₂/Al dispersion fuel plate. A detailed model of the fuel meat swelling is developed. Taking these in-pile behaviors into consideration, the three-dimensional large deformation incremental constitutive relations and stress update algorithms have been developed to study its thermal-mechanical performance under normal conditions using Abaqus. Results have shown that IL can effectively decrease the thermal conductivity of fuel meat. The high Mises stress region mainly locates at the interface between fuel meat and cladding, especially around the side edge of the interface. With irradiation time increasing, the stress in the fuel plate gets larger resulting from the growth of fuel meat swelling but then decreases under the effect of creep deformation. For the cladding, plasticity deformation does not occur within the irradiation time.

• Korea-Australia Rheology Journal
• /
• 제15권1호
• /
• pp.19-25
• /
• 2003

Since the microstructure of functional thin films depends on the dispersion characteristics of dense slurry, it is important to control the agglomerative nature of slurries under processing. The present authors have been discussing the model prediction of agglomerative nature and local rate of agglomeration in dense suspensions. The experiments have been peformed under shear flow using the nearly spherical and oblate type graphite particles. In this study, the experiment has been conducted using water and glycerol as dispersion media. Stress control type rheometer was used to measure the slurry rheology. Local agglomeration of graphite particles has been predicted by using Usui's model. The experimental results show that both the shape and slurry processing method affect on the local dispersion condition. The agglomeration formed by oblate type graphite particles seems to be more difficult to break up than that of spherical particles.

• 한국재료학회지
• /
• 제13권11호
• /
• pp.725-731
• /
• 2003

The effect of organic processing parameters on the dispersion stability of the BaTiO$_3$-based dielectric particles and borosilicate glass particulate suspensions was investigated in a system where organic solvents, dispersant, binder and modifier were used as processing additives in a low temperature cofired ceramic fabrication processes. Two- and three-component organic solvents were used to disperse ceramic particles and it was found the better stability in the particulate suspension prepared in a bi-solvent, which was consists of toluene and ethanol in a non-azeotropic composition. The addition amount of organic additives had a great impact on dispersion in the present investigation. The flow curves of the suspensions prepared with binder and modifier were fitted according to the power-law equation, which indicates that the internal structure of the suspension could be disturbed under the applied shear stress. Finally, the LTCC green tapes were successfully tape-cast based upon the optimum formulation of LTCC suspension and its microstructure was compared with that of the hard-agglomerates.

• Asian Journal of Atmospheric Environment
• /
• 제11권3호
• /
• pp.153-164
• /
• 2017

Odor dispersion around a cubic building from rooftop odor emissions was investigated using computational fluid dynamics (CFD). The Shear Stress Transport (here after SST) $k-{\omega}$ model in FLUENT CFD code was used to simulate the flow and odor dispersion around a cubic building. The CFD simulations were performed for three different configurations of cubic buildings comprised of one building, two buildings or three buildings. Five test emission rates were assumed as 1000 OU/s, 2000 OU/s, 3000 OU/s, 4000 OU/s and 5000 OU/s, respectively. Experimental data from wind tunnels obtained by previous studies are used to validate the numerical result of an isolated cubic building. The simulated flow and concentration results of neutral stability condition were compared with the wind tunnel experiments. The profile of streamline velocity and concentration simulation results show a reasonable level of agreement with wind tunnel data. In case of a two-building configuration, the result of emission rate 1000 OU/s illustrates the same plume behavior as a one-building configuration. However, the plume tends to the cover rooftop surface and windward facet of a downstream building as the emission rate increases. In case of a three-building configuration, low emission rates (<4000 OU/s) form a similar plume zone to that of a two-building configuration. However, the addition of a third building, with an emission rate of 5000 OU/s, creates a much greater odorous plume zone on the surface of second building in comparison with a two-building configuration.

• 폴리머
• /
• 제36권5호
• /
• pp.637-642
• /
• 2012

실리카로 충전된 SBR(styrene butadiene rubber)/BR(butadiene rubber) 합성고무 복합소재에 대해서 가공기기의 구조가 실리카 분산에 미치는 영향을 파악하기 위해 주사전자 현미경(SEM-scanning electron microscope)을 이용하여 컴파운드의 모폴로지를 관찰하였다. Internal mixer 내에서 intermeshing rotor와 tangential rotor에 의해 배합된 컴파운드를 비교한 결과, intermeshing rotor에 의해 가공되었을 경우 실리카 입자가 더 고르게 분산 및 분포되었음을 관찰하였다. Rotor의 geometry 차이에 의해 intermeshing rotor가 tangential rotor보다 더 큰 전단력(shear)을 컴파운드에 전달하여 실리카 입자를 효과적으로 분산 및 분배시킨 것으로 판단된다.

• Earthquakes and Structures
• /
• 제9권1호
• /
• pp.111-126
• /
• 2015

In this study, the coupled effects of magnetic field, stress and thermal field on gravity waves propagating in a liquid layer over a solid surface are discussed. Due to change in temperature, initial hydrostatic stress and magnetic field, the gravity-sound Rayleigh waves can propagate in the liquid-solid interface. Dispersion properties of waves are derived by using classical dynamical theory of thermoelasticity. The phase velocity of gravity waves influenced quite remarkably in the presence of initial stress parameter, magneto-thermoelastic coupling parameter in the half space. Numerical solutions are also discussed for gravity-Rayleigh waves. In the absence of temperature, stress and magnetic field, the obtained results are in agreement with classical results.

• 한국해양학회지
• /
• 제16권2호
• /
• pp.99-107
• /
• 1981

A partial differential equation for the adjusted sea level, obtained from the long wave equations in shallow water, is reduced to a simpler one by the use of physically reasonable approximations based on the observations. The similar equation for the stream function indicates that shelf waves are generated by the longshore wind stress. This indication is in good agreement with the high correlation between the adjusted sea levels and the longshore wind stress. From the dispersion relationship and the boundary conditions, there exist a countable infinite number of modes which satisfy a first-order wave equations. The adjusted sea level for a given wind stress can easily be calculated by utilizing the convolution and the Fourier transformation. Some detailed solutions are presented here for sinusoidal and exponential wind stress.