• Journal of the Korea Institute of Military Science and Technology
• /
• v.14 no.2
• /
• pp.313-320
• /
• 2011

SPH(Smoothed Particle Hydrodynamics) is a gridless Lagrangian technique that is useful as an alternative numerical analysis method used to analyze high deformation problems as well as astrophysical and cosmological problems. In SPH, all points within the support of the kernel are taken as neighbours. The accuracy of the SHP is highly influenced by the method for choosing neighbours from all particle points considered. Typically a linked-list method or tree search method has been used as an effective tool because of its conceptual simplicity, but these methods have some liability in anisotropy situations. In this study, convex hull algorithm is presented as an improved method to eliminate this artifact. A convex hull is the smallest convex set that contains a certain set of points or a polygon. The selected candidate neighbours set are mapped into the new space by an inverse square mapping, and extract a convex hull. The neighbours are selected from the shell of the convex hull. These algorithms are proved by Fortran programs. The programs are expected to use as a searching algorithm in the future SPH program.

• Journal of Sensor Science and Technology
• /
• v.16 no.5
• /
• pp.389-393
• /
• 2007

Soft ferromagnetic materials are very useful for many sensors using magnetic materials demanding high permeability, low coercivity and low hysteresis loss. Among them, FeCoSiBNi amorphous magnetic films show a good impedance change (about 5.01 %/Oe, at 10 MHz) by the exterinal magnetic field in this experiment. The magnetic films are produced by melt-spun method, one of the rapid solidification process. Ribbon shape wires were made from the films, and let them annealed in DC magnetic field to increase the maximum Giant Magneto Impedance ratio. Field annealing decreases the stress and changes the effective anisotropy. Thus, we can find that the impedance change (200.47 %) is improved and the fabricated magnetic wire has characteristics of good sensor element.

• Tunnel and Underground Space
• /
• v.9 no.1
• /
• pp.56-63
• /
• 1999

Rock behaves in a complex way due to the discontinuities. To describe the complicated failure and deformation behavior of rock, many researches were focused on the development of crack models. This study discusses the validity of the sliding and shear crack model to systematically fractured rock, i.e. coal. The model was also implemented into a numerical analysis. For that, a finite element program was modified in several ways. To describe the transverse isotropy in two-dimensional analysis, the stress-strain relationship was modified for the direction of the axis of symmetry. Also, the changes of the effective elastic moduli according to the crack growth were calculated. A simple example of two-dimensional laboratory uniaxial compression test was analyzed. The results coincided with the observations obtained from the laboratory tests.

• Transactions of Materials Processing
• /
• v.26 no.5
• /
• pp.286-292
• /
• 2017

Magnesium alloy shows strong anisotropy and asymmetric behavior in tension and compression curve, especially at room temperature. These characteristics limit the application of finite element method (FEM) which is based on conventional continuum mechanics. To accurately predict the material behavior of magnesium alloy at microstructural level, a methodology of fully coupled multiscale simulation is presented and a crystal plasticity model as a constitutive equation in the simulation of metal forming process is introduced in this study. The existing constitutive equation for rigid plastic FEM is modified to accommodate deviatoric stress component and its derivatives with respect to strain rate components. Viscoplastic self-consistent (VPSC) polycrystal model was selected as a constitutive model because it was regarded as the most robust model compared to Taylor model or Sachs model. Stiffness matrix and load vector were derived based on the new approach and implemented into $DEFORM^{TM}-3D$ via a user subroutine handling stiffness matrix at an elemental level. The application to extrusion and rolling process of pure magnesium is presented in this study to assess the validity of the proposed multiscale process.

• Water for future
• /
• v.29 no.2
• /
• pp.221-233
• /
• 1996

To investigate the hydrodynamic characteristics of a two-dimensional buoyant surface jet, the most important factors of the numerical analysis are the evaluation of the free surface and the turbulence transportation under the stratification. In present study, a numeriacal simulation model used with the semi-implicit method for pressure-linked equations (SIMPLE), the non-hydrostatic approximation and the algebraic stress model (ASM) is applied to investigate the vertical structure of internal flow hydrodynamically. The ASM enables to take account of anisotropy of turbulence, the damping effects of the density interface, and the free surface on the turbulence structure accurately. The ASM tested produces better agreement than the $\kappa-\varepsilon$ model with measurements by Nakatsuji (1984) on the flow development and turbulence structure. Applicability of the ASM to a two-dimensional buoyant surface jet is examined through comparison with experimental data.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2007.10a
• /
• pp.281-284
• /
• 2007

The effect of Ca addition on the microstructure evolution and deformation behavior of AZ31 magnesium alloy produced by hot extrusion was investigated. For this purpose, Ca was added into AZ31 melts to the level of 0.7 and 2.0 wt.% Ca. Then, AZ31 base alloy and Ca modified AZ31 alloys were extruded at $383^{\circ}C$. Ca added alloys showed finer grain size and increased hardness value rather than AZ31 base alloy. After isothermal hot compression, the shape of tested specimen exhibited a noticeable anisotropy due to the crystallographic texture effect. The ratio of major and minor axes of ovality was not directly related to test condition and Ca amount. Flow stress level increases with the increase of Ca addition at temperature below $300^{\circ}C$ because of fine microstructure. However, at high temperature and low strain rate region ($400^{\circ}C$ and $10^{-3}s^{-1}$), reverse tendency was observed since main deformation mechanism changes from dislocation slip to grain boundary sliding or diffusional process at high temperature.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.32 no.9
• /
• pp.720-727
• /
• 2008

Time delay effects on near-wall turbulent structures are investigated by performing a large-eddy simulation of a transient turbulent flow in a pipe. To elucidate the time delay effects on the near-wall turbulence, we selected the dimensionless acceleration parameter which was used in the previous study. Various turbulent statistics revealed the distinctive features of the delay. It was shown that the dynamic Smagorinsky model is valid to capture the alterations of the turbulence physics well. A dimensionless time for the responses of the flow quantities was introduced to give the detailed information on the delay of the nearwall turbulence. The conditionally-averaged flow fields associated with Reynolds shear stress producing events show that sweep and ejections are closely related to the delays of the turbulence production and the turbulence propagation toward the pipe center. The present study suggested that the enhanced anisotropy of the turbulence in the initial and transient stages would be a challenging problem to standard turbulence models.

• International Journal of Highway Engineering
• /
• v.11 no.1
• /
• pp.195-201
• /
• 2009

In this paper, the critical strains for pavement design were calculated from both Layered Elastic Program (LEP) and Finite Element Method (FEM) and the case studies which give similar critical responses were compared. Although FEM has been realized as a superior model, LEP is more favorable to pavement design due to its simplicity and thus, the technique to calculate the correct critical responses using LEP is significant. This study showed that KENLAYER can possibly estimate the critical responses close to ones obtained from TTIPAVE, which considers nonlinear cross-anisotropic behavior of unbound base materials, by adjusting the stress point locations.

• Journal of Power System Engineering
• /
• v.2 no.1
• /
• pp.31-38
• /
• 1998

A diffuser, an important equipment to change kinetic energy into pressure energy, has been studied for a long time. Though experimental and theoretical researches have been done, the understanding of energy transfer and detailed mechanism of energy dissipation is unclear. As far as numerical prediction of diffuser flows are concerned, various numerical studies have also been done. On the contrary, many turbulence models have constraint to the applicability of diffuser-like complex flows, because of anisotropy of turbulence near the wall and of local nonequilibrium induced by an adverse pressure gradient. The existing $k-{\epsilon}$ turbulence models have some problems in the case of being applied to complex turbulent flows. The purpose of this paper is to test the applicability of the nonlinear $k-{\epsilon}$ model concerning diffuser-like flows with expansion and streamline curvature. The results show that the nonlinear $k-{\epsilon}$ turbulence model predicted well the coefficient of pressure, velocity profiles and turbulent kinetic energy distributions, however the shear stress prediction was failed.

• Advances in aircraft and spacecraft science
• /
• v.6 no.2
• /
• pp.157-168
• /
• 2019

The production of nonwoven fabrics from natural fibers is already expanding at an industrial level for simple curvature semi-structural part in the automotive industry. To develop their use for technical applications, this paper provides an experimental study of the mechanical behavior of flax-fiber nonwoven preforms. A comparison between different sets of carded needle-punched nonwoven has been used to study the influence of manufacturing parameters such as fibers' directions, the area and the needle punching densities. We have found that the anisotropy observed between both directions can be reduced depending on these parameters. Furthermore, this work investigates the possibility to form double curvature parts such as a hemisphere as well as a more complex shape such as a square box which possesses four triple curvature points. We propose a forming process adapted to the features of the nonwoven structure. The purpose is to determine their behavior under high stress during various forming settings. The preforming tests allowed us to observe in real time the manufacturing defects as well as the high deformability potential of flax nonwoven.