• Proceedings of the KIPE Conference
• /
• 2018.07a
• /
• pp.320-321
• /
• 2018

A non-isolated high voltage gain bidirectional DC-DC converter for battery storage system has been presented in this paper. The topology is composed of boost converter and traditional SEPIC converter. The proposed converter can achieve higher voltage conversion ratio with reduced voltage and current stresses in the switches. In additional, a reduced number of components are included in this topology. The PSIM simulation is carried to validate the analysis and operation of the converter.

• Proceedings of the KIEE Conference
• /
• 2001.07d
• /
• pp.1982-1983
• /
• 2001

직류 100 kV 까지 고전압의 국가 측정표준을 확립하기 위하여 저항형 분압기의 비율을 정밀 측정하는 방법을 고안하였다. 일반적으로 저항형 분압기의 비율은 사용 전압에 따라 변하므로 저항과 전압비율을 동시에 측정하는 기술이 요구된다. 본 발표에서는 고안된 binary step-up 방법의 원리를 설명하고 실제 적용 시 예상되는 불확도를 계산하고자 한다.

• Proceedings of the KIPE Conference
• /
• 2015.07a
• /
• pp.163-164
• /
• 2015

본 논문에서는 고승압비를 갖는 단일스위치 ZCS 병렬 공진 컨버터를 제안한다. 제안하는 컨버터는 단일스위치를 사용하여 구조가 간단하며 병렬 공진회로를 이용하여 고승압이 가능하다. 또한, 별도의 클램프 회로 없이 전 부하영역에서 스위치의 ZCS 턴온 및 턴오프와 다이오드의 ZCS 턴오프를 성취한다. 제안하는 컨버터는 250W 시작품을 제작하여 타당성을 검증하였다.

• Journal of Power Electronics
• /
• v.16 no.6
• /
• pp.2035-2044
• /
• 2016

In order to match the voltages between high voltage battery stacks and low voltage super-capacitors with a high conversion efficiency in hybrid energy sources electric vehicles (HESEVs), a high ratio bidirectional DC-DC converter with a synchronous rectification H-Bridge is proposed in this paper. The principles of high ratio step-down and step-up operations are analyzed. In terms of the bidirectional characteristic of the H-Bridge, the bidirectional synchronous rectification (SR) operation is presented without any extra hardware. Then the SR power switches can achieve zero voltage switching (ZVS) turn-on and turn-off during dead time, and the power conversion efficiency is improved compared to that of the diode rectification (DR) operation, as well as the utilization of power switches. Experimental results show that the proposed converter can operate bidirectionally in the wide ratio range of 3~10, when the low voltage continuously varies between 15V and 50V. The maximum efficiencies are 94.1% in the Buck mode, and 93.6% in the Boost mode. In addition, the corresponding largest efficiency variations between SR and DR operations are 4.8% and 3.4%. This converter is suitable for use as a power interface between the battery stacks and super-capacitors in HESEVs.

• Journal of the Korean Institute of Intelligent Systems
• /
• v.13 no.4
• /
• pp.461-468
• /
• 2003

In a sequence of images obtained by surveillance cameras, facial regions appear very small and their colors change abruptly by lighting condition. This paper proposes a new face detection scheme, robust on complex background, small size, and lighting conditions. The proposed method is consisted of three processes. In the first step, the candidates for the face regions are selected using face color distribution and motion information. In the second stage, the non-face regions are removed using face color ratio, boundary ratio, and average of column-wise intensity variation in the candidates. The face regions containing eyes and mouth are segmented and classified, and then they are scored using their topological relations in the last step. To speed up and improve a performance the above process, a block based image segmentation technique is used. The experiments have shown that the proposed algorithm detects faced regions with more than 91% of accuracy and less than 4.3% of false alarm rate.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.11 no.9
• /
• pp.893-900
• /
• 2016

Output response for prototype system is analyzed according to the pole locations and the damping ratio changes. The system modeling is constructed for RLC-circuit and the output response is analyzed for both a unit-step and a sinusoidal input. The survey is conducted to estimate the understanding ability on the automatic control. A high understanding ability is shown up in analysing the transfer functions of control system. And improvement is manifest in the ability to understand the output response according to the parameter changes. But some difficulty is revealed in acquiring the output responses in time domain.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.13 no.2
• /
• pp.79-87
• /
• 2008

Boost Converters have been used to step up and regulate the low and widely varing voltage from the fuel cell. A transformer-less boost converter which does not have lossy, bulky, and costly high frequency transformers has an advantage in applications where galvanic isolation is not required. In this paper a new transformer-less boost converter is proposed. The proposed boost converter has practically usuable 6 to 8 times of step up ratio and is suitable for fuel cell applications due to very low input and output current ripples. The proposed converter is verified through the theorical analysis, simulation and experimental waveform.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.13 no.2
• /
• pp.119-127
• /
• 2008

In this paper, the modular line-connected photovoltaic PCS (photovoltaic power conditioning system) is proposed. A step-up DC-DC converter using a active-clamp circuit and a dual series-resonant rectifier is proposed to achieve a high efficiency and a high input-output voltage ratio efficiently. An IncCond (incremental conductance) MPPT (maximum power point tracking) algorithm that improves MPPT characteristic is used. The PV module current is estimated without using a DC current sensor. By control a inverter using a linearized output current controller, a unity power factor is achieved. All algorithms and controllers are implemented on a single-chip microcontroller and the superiority of the proposed DC-DC converter and controllers is proved by experiments.

• Proceedings of the KIPE Conference
• /
• 2003.11a
• /
• pp.238-243
• /
• 2003

The solar cells should be operated at the maximum power point because its output characteristics are greatly fluctuated on the variation of insolation, temperature and load. The output power of solar cell is DC, therefore it is necessary to install an inverter among electric power converts. The inverter have to supply a sinusoidal current and voltage to the load and the interactive utility line. In the paper, the proposes a photovoltaic system designed with a step up chopper and single phase PWM voltage source inverter. Synchronous signal and control signal was processed by microprocessor for stable modulation. The step up chopper operates in continuous mode by adjusting the duty ratio so that the photovoltaic system tracks the maximum power point of solar cell without any influence on the variation of insolation and temperature because solar cell has typical dropping character. The single phase PWM voltage source inverter consists of complex type of electric power converter to compensate for the defect, that is, solar cell cannot be developed continuously by connecting with the source of electric power, from 10 to $20\%$. The single phase PWM voltage source inverter operates in situation that its output voltage is in same phase with the utility voltage. The inverter supplies an ac power with high factor and low level of harmonics to the load and the utility power system.

• Journal of Power Electronics
• /
• v.18 no.3
• /
• pp.662-671
• /
• 2018

This paper presents a new structure for a step up dc-dc converter, which has several advantageous features. Firstly, the input dc source and the clamped capacitor are connected in series to transfer energy to the load through dual voltage multiplier cells. Therefore, the proposed converter can produce a very high voltage and a high conversion efficiency. Secondly, a double voltage clamped circuit is introduced to the primary side of the coupled inductor. The energy of the leakage inductance of the coupled inductor is recycled and the inrush current problem of the clamped circuits can be shared equally by two synchronous clamped capacitors. Therefore, the voltage spike of the switch tube is solved and the current stress of the diode is reduced. Thirdly, dual voltage multiplier cells can absorb the leakage inductance energy of the secondary side of the coupled inductor to obtain a higher efficiency. Fourthly, the active switch turns on at almost zero current and the reverse-recovery problem of the diodes is alleviated due to the leakage inductance, which further improves the conversion efficiency. The operating principles and a steady-state analysis of the continuous, discontinuous and boundary conduction modes are discussed in detail. Finally, the validity of this topology is confirmed by experimental results.