• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.16 no.2 s.107
• /
• pp.190-197
• /
• 2006

It is well known that the acoustic characteristics of the sea are significantly affected by bubbles which have their own inherent characteristics at the undersea. In this study, the shape and acoustic characteristics of air bubbles generated by an underwater nozzle are calculated numerically, and are measured with a high speed camera and a hydrophone at various air flow rates in the experimental apparatus. As a result of analysis, the shape calculated numerically well matched with measured values at low flow rates, but in case of relatively higher flow rates. the use of correction coefficient is needed for more accurate estimation of the bubble shape. And also the rising velocity of a single bubble is constant regardless of both the bubble size and the flow rate. and the acoustic signal generated when the bubble is produced by an underwater nozzle has the same characteristic of natural frequency of the bubble pulsation, and is agreed with Minnaert's equation if the correction coefficient is considered in accordance with the flow rate.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.18 no.2
• /
• pp.238-246
• /
• 2008

This case study refers to turbine-generator with retrofitted turbine rotor. Vibration problem occurring after the retrofit was mainly due to high vibration from exciter side. However, repeated test run and operation during scheduled maintenance caused high vibration from generator bearing, and post-overhaul test run before turbine vibration correction caused oil whip on the bearing. This case study shows how to analyze vibration condition of high turbine generator vibration detected during the post-overhaul test run and vibration condition of offline and online data to reflect it on establishing maintenance schedule and overhaul correction procedure. Vibration data could be acquired during steady load operation or even with varying speed and load. Each data is important for machinery condition evaluation. This case study shows that the vibration data during extreme condition is the key factor in analysis, which helps to find the machinery problem.

• Journal of the Korean Solar Energy Society
• /
• v.29 no.2
• /
• pp.70-75
• /
• 2009

In this experiment, we did sampling 6 kinds of photovoltaic modules and analyzed the discrepancy of measurement results between l laboratory and 4 PV makers to have performance repeatability at Standard Test Condition(STC) condition. From the KIER's results, Korea's standard test laboratory, other laboratory showed -10% measurement variation. The causes came from correction of reference cell, test condition and the state of skill. Form the comparison test, we analyzed the problems. But three PV maker reduced measurement variation, other one PV maker and one test laboratory didn't improve the problems of correction of reference cell, test condition and the state of skill. Also, High Efficiency Module had a big discrepancy of -10.0$\sim$-6.2% among 3 laboratories which have a less than 10msec light pulse duration time. This made low spectrum response speed so the Fill Factor decreased maximum output power under 10msec light pulse duration time

• 한국지구과학회:학술대회논문집
• /
• 2010.04a
• /
• pp.59-62
• /
• 2010

The limitation of constant for tide correction is identified using the T_tide $MATLAB^{(R)}$ package. A suggestion is presented in calculation of local phase lag(k) by a/15 (a is angular speed of any constituent in degree) from the g, phase lag measured by standard time meridian latitude.

• The Journal of Engineering Research
• /
• v.1 no.1
• /
• pp.49-57
• /
• 1997

In this paper, the follow-up works of Habermann's deadlock avoidance algorithm is investigated from the view of correction, efficiency and concurrency. Habermann's deadlock avoidance algorithm is briefly surveyed and in-depth discussion of follow-up algorithms modified and improved is presented. Then, further improvement of Kameda's algorithm will be discussed. His algorithm for testing deadlock-freedom in computer system converts the Habermann's model into a labeled bipartite graph so that the deadlock detection problem can be equivalent to finding complete matching for Mormon marriage problem. His algorithm has a running time of O($mn^1.5$) because Dinic's algorithm is used. The speed of above algorithm can be enhanced by employing a faster algorithm for finding a maximal matching. The wave method by Kazanov is used for.

• Current Optics and Photonics
• /
• v.2 no.6
• /
• pp.612-622
• /
• 2018

In wave-front-sensor-less adaptive optics (WFS-less AO) systems, the Jacopo Antonello (JA) method belongs to the model-based class and requires few iterations to achieve acceptable distortion correction. However, this method needs a lot of measurements, especially when it deals with moderate or severe aberration, which is undesired in free-space optical communication (FSOC). On the contrary, the stochastic parallel gradient descent (SPGD) algorithm only requires three time measurements in each iteration, and is widely applied in WFS-less AO systems, even though plenty of iterations are necessary. For better and faster compensation, we propose a WFS-less hybrid approach, borrowing from the JA method to compensate for low-order wave front and from the SPGD algorithm to compensate for residual low-order wave front and high-order wave front. The correction results for this proposed method are provided by simulations to show its superior performance, through comparison of both the Strehl ratio and the convergence speed of the WFS-less hybrid approach to those of the JA method and SPGD algorithm.

• Advances in Energy Research
• /
• v.6 no.1
• /
• pp.35-54
• /
• 2019

A successful blade design must satisfy some criterions which might be in conflict with maximizing annual energy yield for a specified wind speed distribution. These criterions include maximizing power output, more resistance to fatigue loads, reduction of tip deflection, avoid resonance and minimize weight and cost. These criterions can be satisfied by modifying the geometrical parameters of the blade. This study is dedicated to the aerodynamic assessment of a 20 kW horizontal axis wind turbine operating with two possible airfoils; that is $G{\ddot{o}}ttingen$ 413 and NACA 2415 airfoils (the Gottingen airfoil never been used in wind turbines). For this study parameters such as chord (constant, tapered and elliptic), twist angle (constant and linear) are varied and applied to the two airfoils independently in order to determine the most adequate blade configuration that produce the highest annual energy output. A home built numerical code based on the Blade Element Momentum (BEM) method with both Prandtl tip loss correction and Glauert correction, X-Foil and Weibull distribution is developed in Matlab and validated against available numerical and experimental data. The results of the assessment showed that the NACA 2415 airfoil section with elliptic chord and constant twist angle distributions produced the highest annual energy production.

• The Journal of Economics, Marketing and Management
• /
• v.6 no.3
• /
• pp.14-25
• /
• 2018

Purpose - Taxes cover all aspects of society, especially in terms of resource allocation and economic growth. In reality, the tax revenue is often used to measure the quality of a country's economy. The relationship between tax revenue and economic growth has been paid much attention by academic circles. Due to this background, this paper attempts to investigate the mutual effect between tax revenue and economic growth. Research design, data, and Methodology - The annual datum form 1980 to 2017 are employed to conduct an empirical analysis under the vector error correction model. In this paper, the GDP is treated as an independent variable. The tax revenue is treated as a dependent variable. Furthermore, a menu of statistic approaches will be used to testify the mutual effect between tax revenue and economic growth. Results - Via the co-integration test, the results report that the tax revenue has a positive effect on economic growth in the long run. Through the vector error correction estimation, the results also report that the tax revenue also has a positive effect on economic growth in the short run. Conclusions - This paper provides a view that the tax revenue is a kind of a determinant to promote economic growth. Therefore, the China's government should pay much attention to the improvement of tax revenue system so as to maintain a high-speed economic growth.

• The Journal of the Korea Contents Association
• /
• v.5 no.4
• /
• pp.11-19
• /
• 2005

With the development of IT technologies, IT environment is making great change over life whole and is displacing business and business achievement systems of industry at the fast speed. The system which is proposed in this paper, supports environments to share codes, execution files and objects between project teams to maximize productivity and efficiency in web environments. Through impact assessment which is achieved at correction and development of existing programming codes by maintenance requirements, it minimizes obstacle occurrence factors and supports tracing obstacle sources. Through conversion the correction and development histories of existing sources and executable files between project teams to XML documents suitable to share in web, it stores them to relational database. In this paper, through impact assessment and change management for the correction and development of applications in the existing system development environments, we support efficient IT developments.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.16 no.8
• /
• pp.1759-1764
• /
• 2012

This paper describes FPGA design and realization using the shading correction algorithm for a CCD scan image enhancement. The shading algorithm is used by LUT (Look-up Table). The image enhancement results from that the histogram minimum value and maximum with respect to all pixels of the CCD image should be extracted, and the shading LUT is constructed to keep constant histogram with offset data. The output of sensor be converted to corrected LUT image in preprocessing, and the converting system is realized by FPGA to be enabled to operate in real time. The result of the experimentation for the proposed system is showed to take the scanning time 2.4ms below. The system is presented to be based on a low speed processor system to scan enhanced images in real time and be guaranteed to be low cost.