• 소음진동
• /
• 제10권5호
• /
• pp.873-879
• /
• 2000

Experimental investigation was conducted to study the effects of pitch angle maximum camber on the performance and noise of an axial-flow fan used in outdoor-unit of air -conditioner. For this study the axial-flow fan whose pitch angle can be varied was made and the Specific sound Pressure Level and other coefficients were measured using the anechoic fan tester. It is found that pitch angle affects more severly than the maximum camber on the fan performance. On the while the maximum camber affects much on the specific sound power level. Present results show that it is important to choose the optimum pitch angle and maximum camber to design the high-performance and low-noise axial-flow fan and specific noise measured in the anechoic fan tester can be sued effectively for the design of low-noise fan.

• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제49권8호
• /
• pp.438-444
• /
• 2000

We report the effects of etch process parameters on the ohmic contact formation in the plasma etching of GaN. Planar inductively coupled plasma system with $CH_4/H_2/Ar$gas chemistry has been used as etch reactor. The contact resistance and the specific contact resistance have been investigated using transfer length method as a function of RF bias power and %Ar gas concentration in total flow rate. AES(Auger electron spectroscopy) analysis revealed that the etched GaN has nonstoichiometric Ga rich surface and was contaminated by carbon and oxygen. Especially large amount of carbon was detected at the sample etched for high bias power (or voltage) condition, where severe degradation of contact resistance was occurred. We achieved the low ohmic contact of $2.4{\times}10^{-3} {\Omega}cm^2$ specific contact resistance at the input power 400 W, RF bias power 150 W, and working pressure 10mTorr with 10 sccm $CH_4$, 15 sccm H2, 5 sccm Ar gas composition.

• Membrane and Water Treatment
• /
• 제8권3호
• /
• pp.279-292
• /
• 2017

This study was aimed at ultrafiltration (UF) as a pretreatment before reverse osmosis (RO) within the scheme of hybrid reverse osmosis-multistage flush (RO-MSF) desalination. Seawater at elevated temperature (after MSF heat-exchangers) was used as a feed in this process. The pretreatment system was represented as a set of functionally-linked technological segments such as: UF filtration, backwashing, chemical- enhanced backwashing, cleaning, waste disposal, etc. The process represents the sequences of operating cycles. The cycle, in turn, consists of the following unit operations: filtration, backwashing and chemical-enhanced backwashing (CEB). Quantitative assessment was based on the following indicators: normalized permeability, transmembrane pressure, specific energy and water consumption, specific waste generation. UF pre-treatment is accompanied by the following waste streams: $W1=1.19{\times}10$ power of $-2m^3$ (disposed NaOCl with 0.0044% wt.)/$m^3$ (filtrate); $W2=5.95{\times}10$ power of $-3m^3$ (disposed $H_2SO_4$ with 0.052% wt.)/$m^3$(filtrate); $W3=7.26{\times}10$ power of $-2m^3$ (disposed sea water)/$m^3$ (filtrate). Specific energy consumption is $1.11{\times}10$ power of $-1kWh/m^3$ (filtrate). The indicators evaluated over the cycles with conventional (non-chemical) backwashing were compared with the cycles accompanied by CEB. A positive impact of CEB on performance indicators was demonstrated namely: normalized UF resistance remains unchanged within the regime accompanied by CEB, whereas the lack of CEB results in 30% of its growth. Those quantitative indicators can be incorporated into the target function for solving different optimization problems. They can be used in the software for optimisation of operating regimes or in the synthesis of optimal flow- diagram. The cycle characteristics, process parameters and water quality data are attached.

• 전자공학회논문지
• /
• 제50권7호
• /
• pp.109-114
• /
• 2013

전력 MOSFET(산화물-반도체 전위 효과 트랜지스터)는 BLDC 모터와 전력 모듈 등에 광범위하게 사용하고 있다. 기존 전력 MOSFET 구조는 온-저항과 항복전압사이에 절충(tradeoff)이 필요하다. 이러한 절충을 하지 않고 최적화를 하기위해 비균일 초접합 트랜치 MOSFET 를 설계하는데 동일한 항복전압에서 균일 초접합 트랜치 MOSFET보다 낮은 온-저항을 갖도록한다. 이를 위해 드리프트 영역에서 우수한 전기장 분포를 달성하기 위하여 선형구조의 도핑 프로파일을 제안하고, 단위 셀 설계, 도핑농도의 특성분석, 전위분포를 SILVACO TCAD 2D인 Atlas 소자 소프트웨어를 사용하여 시뮬에이션을 수행하였다. 결과로 100V 급 MOSFET에서 비균일 초접합 트랜치 MOSFET가 균일 초접합 트랜치 MOSFET보다 온-저항에서 우수한 특성을 보여주고 있다.

• 재무관리연구
• /
• 제21권1호
• /
• pp.183-204
• /
• 2004

본 연구는 한국주식시장에서 관찰 가능한 주식간 동적 연결구조를 도출하고, 관찰된 연결구조가 어떤 방식으로 형성되는지에 대한 기존연구의 결과를 보다 심층적으로 검증하고자 하였다. 즉, 주식간 동적 연결구조가 Power Law분포를 따른다는 기존 연구결과에서, 왜 대부분의 주식은 다른 주식과 2개이하의 연결개수를 갖고, 왜 일부 주식이 다른 주식들과 많은 연결개수를 갖는지에 대한 원인을 규명하고자 하였다. 그리고, 검증결과의 신뢰성을 높이기 위하여 다양한 각도의 검증방법을 채택하여 분석하였다. 검증결과에 의하면, Mantegna의 검증방법에 의하여 도출된 주식간 동적 연결구조에서 관찰된 주식간 연결개수는 기본적으로 해당주식이 개별주식의 고유속성을 많이 갖는가 아니면 시장지수와의 공통속성이 높은가에 기인한다는 것을 확인할 수 있었다. 즉, 다른 주식과 많은 연결개수를 갖는 주식일수록 시장지수와의 공통속성이 높은 경향이 있고, 다른 주식과 작은 연결개수를 갖는 주식일수록 개별주식의 고유속성이 높은 경향이 있다는 것을 관찰할 수 있었다. 그리고, 이러한 결론은 다양한 각도의 분석에서도 일관된 결과를 관찰하였다.

• 한국터널지하공간학회 논문집
• /
• 제20권4호
• /
• pp.687-699
• /
• 2018

해저터널의 시공은 육상터널의 시공과 몇 가지 다른 부분이 존재하는데 지하수 이외에 해수가 존재하여 고수압을 받으며, 시공 중 지반보강이 육상터널보다 매우 어려운 점 등이 대표적이다. 그러므로 해저터널 시공 시 시공트러블 발생의 예방은 매우 중요하다. 본 고에서는 서해안 해저 약 60 m에 시공한 소형 슬러리 TBM의 굴진 성능을 분석하기 위하여 대상 지반의 지질학적 특성들과 기계적 특성들을 DB로 구축하였다. 구축한 DB 중 추력, 토크 및 RPM 등이 순굴진율에 주는 영향을 확인하고자 각 변수들 간의 상관분석을 실시하였다. 또한 구축된 DB로부터 비에너지와 FPI와의 상관관계를 분석하고 순 굴진율을 예측할 수 있는 경험식을 제시하였다.

• 대한임베디드공학회논문지
• /
• 제2권3호
• /
• pp.194-201
• /
• 2007

As the performance of the mobile terminal becomes higher, the power consumption gradually increases. As a result, power management is one of the most important issues in mobile system with battery. In this paper, we describe an DPM(Dynamic Power Management) using DVS(Dynamic Power Management) as a power management mechanism in Qplus operating system. DVS generally considers a specific device such as CPU, whereas we consider the relations with other hardware components as well as each component. We specially focus on the relation between CPU, memory and LCD devices. We also designs a kernel monitor to collect information to decide the policy for power management. According to the experimental results, the proposed method enables to save much power.

• 한국항해학회지
• /
• 제24권3호
• /
• pp.147-155
• /
• 2000

In this paper, we propose the Chaos Fuzzy controller to analyze the chaotic character of time series obtained from the specific plant and to predict the short-term for power consumption of the plant using the Fuzzy controller. We compared the predicted data with the active ones and checked the error generated by them after we time series of supplied power to the proposed controller. As a result of the simulation, we obtained a admirable consequence that the proposed controller can be advanced through various and accurate data acquisition, and continuous analysis of the resident and industrial environment.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 1998년도 Proceedings ICPE 98 1998 International Conference on Power Electronics
• /
• pp.535-540
• /
• 1998

This paper discusses a triple stage current source GTO inverter system for high power motor drives. The energy rebound circuit of the triple stage inverter not only controls the spike voltage of the GTO inverter but also facilitates PWM control of the thyristor rectifier operated at unity fundamental input power factor. Based on Pspice simulation and experiments, the principles and PWM pulse pattern for removing specific lower harmonics in the inverter's output current are discussed in detail.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2010년도 하계학술대회 논문집
• /
• pp.178-179
• /
• 2010

This paper presents a simulation model and analysis of grid-tied wind turbine generator with batteries using the PSCAD/EMTDC software. The modeled system is consist of two inverters and one bidirectional DC/DC converter. These inverter are to capture the maximum active power under varying wind conditions and to keep the DC-Link voltage magnitude at a specific level. And the bidirectional DC/DC converter makes battery charging or discharging depend on power gap between wind turbine output and local load. Aerodynamic models are applied for a wind turbine blade simulator.