• 한국안전학회지
• /
• 제29권4호
• /
• pp.34-41
• /
• 2014

The goal of this study is to investigate some crack behaviors which affect the crack propagation angle at the planar solid oxide fuel cell with cracks under the fabricating and operating temperature and analyze the stresses by 3 steps processing on the solid oxide fuel cell. Currently, there are lots of researches of the performance improvement for fuel cells, and also for the more powerful efficiency. However, the planar solid oxide fuel cell has demerits which the electrode materials have much brittle properties and the thermal condition during the operating process. It brings some problems which have lower reliability owing to the deformation and cracks from the thermal expansion differences between the electrolyte, cathode and anode electrodes. Especially the crack in the corner of the electrodes gives rise to the fracture and deterioration of the fuel cells. Thus it is important to evaluate the behavior of the cracks in the solid oxide fuel cell for the performance and safety operation. From the results, we showed the stress distributions from the cathode to the anode and the effects of the edge crack in the electrolyte and the slant crack in the anode. Futhermore the crack propagation angle was expected according to the crack length and slant angle and the variation of the stress intensity factors for the each fracture mode was shown.

• 한국세라믹학회지
• /
• 제50권2호
• /
• pp.163-167
• /
• 2013

A modified two-point impedance spectroscopy technique exploits the geometric constriction between an electrolyte and a cathode with an emphasis on semispherical-shaped electrolytes. The spatial limitation in the electrolyte/electrode interface leads to local amplification of the electrochemical reaction occurring in the corresponding electrolyte/electrode region. The modified impedance spectroscopy was applied to electrical monitoring of a YSZ ($Y_2O_3$-stabilized $ZrO_2$)/SSC ($Sm_{0.5}Sr_{0.5}CoO_3$) system. The resolved bulk and interfacial component was numerically analyzed in combination with an equivalent circuit model. The effectiveness of the "spreading resistance" concept is validated by analysis of the electrode polarization in the cathode materials of solid oxide fuel cells.

• Macromolecular Research
• /
• 제12권2호
• /
• pp.145-155
• /
• 2004

Facilitated transport membranes for the separation of olefin/paraffin mixtures have long been of interest in separation membrane science because olefins, such as propylene and ethylene, which are important chemicals in petrochemical industries, are currently separated by energy-intensive cryogenic distillation processes. Recently, solid polymer electrolyte membranes containing silver ions have demonstrated remarkable performance in the separation of olefin/paraffin mixtures in the solid state and, thus, they can be considered as alternatives to cryogenic distillation. Here, we review recent progress, and critical issues affecting in the use of facilitated olefin transport membranes; in particular, we provide a general overview with reference to carrier properties, transport mechanisms, and separation performance.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1996년도 하계학술대회 논문집 C
• /
• pp.1700-1702
• /
• 1996

Solid oxide fuel cell(SOFC) is an electrochemical energy device which converts the free energy of fuel gas directly to electric energy. SOFC has several diratinct advantages over other types of fuel cells: no use of noble metals, no requirement of a reformer, no problem of liquid electrolyte management, and no problem of corrosion by liquid electrolyte. In this study, we have investigated the cell components and the single cell of the planar SOFC fabricated by composite plate process, in which green films of electrolyte, anode and cathode were co-fired. The planar SOFCs were tested and the cell performance characteristics wag evaluated by using electrochemical methods.

• Bulletin of the Korean Chemical Society
• /
• 제32권1호
• /
• pp.105-108
• /
• 2011

The cycling behavior of $Li_4Ti_5O_{12}$ electrode in the ionic liquid (IL)-based electrolytes containing 1-butyl-1-methylpyrrolidinium bis(trifluoromethanesulfonyl) imide and a small amount of additive (vinylene carbonate, ethylene carbonate, fluoroethylene carbonate) was investigated. The $Li_4Ti_5O_{12}$ electrode in the IL electrolyte with an additive exhibited reversible cycling behavior with good capacity retention. Electrochemical impedance spectroscopy and FTIR studies revealed that an electrochemically stable solid electrolyte interphase was formed on the $Li_4Ti_5O_{12}$ electrode in the presence of vinylene carbonate and ethylene carbonate during cycling.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 1999년도 추계학술대회 논문집
• /
• pp.228-231
• /
• 1999

The preparation and electrical properties of LIPON electrolyte were investigated in order to fabricate all solid state thin film battery. The LIPON thin film was deposited by r.f. sputtering of Li$_3$PO$_4$ target in O$_2$-N$_2$ mixtures. The LIPON deposited at N$_2$+10% O$_2$ ratio had a conductivity at 25 $^{\circ}C$ of 1.8${\times}$10$\^$-6/S/cm. The ion conductivity of the LIPON films decreased as the O$_2$ content of the process gas increased.

• Journal of Electrochemical Science and Technology
• /
• 제15권2호
• /
• pp.261-267
• /
• 2024

An unconventional fabrication technique of nanoelectrode was developed using atomic force microscopy (AFM) and hydrogel. Until now, the precise control of electroactive area down to a few nm² has always been an obstacle, which limits the wide application of nanoelectrodes. Here, the nanometer-sized contact between the boron-doped diamond (BDD) as conductive AFM tip and the agarose hydrogel as solid electrolyte was well governed by the feedback amplitude of oscillation in the non-contact mode of AFM. Consequently, this low-cost and feasible approach gives rise to new possibilities for the fabrication of nanoelectrodes. The electroactive area controlled by the set point of AFM was investigated by cyclic voltammetry (CV) of the ferrocenmethanol (FcMeOH) combined with quasi-solid agarose hydrogel as an electrolyte. Single copper (Cu) nanoparticle was deposited at the apex of the AFM tip using this platform whose electrocatalytic activity for nitrate reduction was then investigated by CV and Field Emission-Scanning Electron Microscopy (FE-SEM), respectively.

• 한국세라믹학회지
• /
• 제41권8호
• /
• pp.593-598
• /
• 2004

1 $\mu$m이하의 전고상 리튬 박막전지의 구현을 위해 펄스 레이저 증착법을 이용하여 Pt/TiO$_2$/SiO$_2$/Si 기판위에 LiCoO$_2$정극을 증착온도와 Li/Co 간의 몰 비율을 변화시켜가며 성장시켰다. 특히, Li/Co=1.2의 조성을 갖는 LiCoO$_2$를 50$0^{\circ}C$의 증착온도에서 성장시킬 경우 53 $\mu$Ah/$cm^2$-$\mu$m의 높은 초기 용량값을 가지며 100 싸이클 후에도 67.6%의 용량값을 유지하였다. LiCoO$_2$/Pt/TiO$_2$/SiO$_2$/Si위에 고체 전해질인 (Li, La)TiO$_3$를 비정질상으로 하여 PLD방법으로 낮은 온도대역에서 증착온도를 다양하게 하여 증착하였다. 10$0^{\circ}C$의 증착온도에서 LiCoO$_2$Pt/TiO$_2$/SiO$_2$/Si위에 성장시킨 (Li, La)TiO를 가지고 LiClO$_4$ in PC 안에서 Li anode와 충$.$방전 측정 결과 약 51$\mu$Ah/$cm^2$-$\mu$m의 초기 용량값을 나타내었으며 100싸이클 후에도 90%의 훌륭한 방전용량의 보존력을 나타내었다. 비정질상의 (Li, La)TiO$_3$ 고체 전해질은 전고상 박막전지로의 구현이 가능하다.

• 한국세라믹학회지
• /
• 제56권2호
• /
• pp.111-129
• /
• 2019

Recently, all-solid-state batteries (ASSBs) have attracted increasing interest owing to their higher energy density and safety. As the core material of ASSBs, the characteristics of the solid electrolyte largely determine the performance of the battery. Thus far, a variety of inorganic solid electrolytes have been studied, including the NASICON-type, LISICON-type, perovskite-type, garnet-type, glassy solid electrolyte, and so on. The garnet Li₇La₃Zr₂O₁₂ (LLZO) solid electrolyte is one of the most promising candidates because of its excellent comprehensively electrochemical performance. Both, experiments and theoretical calculations, show that cubic LLZO has high room-temperature ionic conductivity and good chemical stability while contacting with the lithium anode and most of the cathode materials. In this paper, the crystal structure, Li-ion transport mechanism, preparation method, and element doping of LLZO are introduced in detail based on the research progress in recent years. Then, the development prospects and challenges of LLZO as applied to ASSBs are discussed.

• Journal of Electrochemical Science and Technology
• /
• 제11권4호
• /
• pp.411-420
• /
• 2020

Undesirable interfacial reactions between the cathode and sulfide electrolyte deteriorate the electrochemical performance of all-solid-state cells based on sulfides, presenting a major challenge. Surface modification of cathodes using stable materials has been used as a method for reducing interfacial reactions. In this work, a precursor-based surface modification method using Zr and Mo was applied to a LiNi_0.6Co_0.2Mn_0.2O₂ cathode to enhance the interfacial stability between the cathode and sulfide electrolyte. The source ions (Zr and Mo) coated on the precursor-surface diffused into the structure during the heating process, and influenced the structural parameters. This indicated that the coating ions acted as dopants. They also formed a homogenous coating layer, which are expected to be layers of Li-Zr-O or Li-Mo-O, on the surface of the cathode. The composite electrodes containing the surface-modified LiNi_0.6Co_0.2Mn_0.2O₂ powders exhibited enhanced electrochemical properties. The impedance value of the cells and the formation of undesirable reaction products on the electrodes were also decreased due to surface modification. These results indicate that the precursor-based surface modification using Zr and Mo is an effective method for suppressing side reactions at the cathode/sulfide electrolyte interface.