• Corrosion Science and Technology
• /
• v.15 no.6
• /
• pp.297-302
• /
• 2016

Water-based systems are dominating the coating market because of worldwide VOCs regulations. Research is focusing especially on waterborne polyurethane (WPU) because of its unique mechanical and chemical properties. However, commercial WPU consists of linear thermoplastic polymers with polar groups on the main chain, which do not perform as well as solvent-borne PU in a two-pack system. In this study, APTES were used as a chain crosslink agent to overcome commercial WPU's limited performance. WPUs synthesized by using a sol-gel process were evaluated with FT-IR, particle analysis, TGA, tensile tests, pull-off tests, SEM, and EIS. The results showed that WPUs with added APTES had better thermal stability, mechanical properties, and water resistance than did WPUs without added APTES. Consequently, the sol-gel process increased the crosslink density of WPUs and modified the WPU's own properties.

• Bulletin of the Korean Chemical Society
• /
• v.33 no.7
• /
• pp.2315-2319
• /
• 2012

To improve the performance of $LiFePO_4F$, a novel sol-gel process is developed. For comparison, ceramic process is also implemented. From X-ray diffraction results we know that each sample adopts a triclinic $P{\bar{1}}$ space group, and they are isostructural with amblygonite and tavorite. The scanning electron microscope images show that the homogeneous grains with the dimension of 300-500 nm is obtained by the sol-gel process; meanwhile the sample particles obtained by ceramic process are as big as 1000-3000 nm. By galvanostatic tests and at electrochemical impedance spectroscopy method, the sample obtained by sol-gel process presents better electrochemical properties than the one obtained by ceramic process.

• Bulletin of the Korean Chemical Society
• /
• v.24 no.11
• /
• pp.1599-1604
• /
• 2003

New methods were developed to prepare silver-doped sol-gel films for surface-enhanced Raman spectroscopy (SERS) applications. First, silver ions were doped into a sol-gel matrix. The doped silver ions were reduced into corresponding silver metal particles by two reductive procedures; chemical reduction and thermal reduction. The SERS spectra of benzoic acid were used to demonstrate the SERS effect of the new substrates. The adsorption strength of benzoic acid adsorbed on differently reduced substrates was discussed. The possible adsorption form and the orientation of adsorbate were also discussed.

• Journal of the Korean Ceramic Society
• /
• v.37 no.7
• /
• pp.625-631
• /
• 2000

In this study, the characteristics and sinterablities of TiO2 powders which were fabricated on sol-gel process and supercritical fluid process were examined. The powders fabricated on sol-gel process were amorphous. The particle size and shape were changed with the amount of water used for hydrolysis of titanium ethoxide. The powders were changed from amorphous to crystalline by heating at 400℃. The crystalline anatase TiO2 powders were directly prepared in ethanol supercritical fluid condition that temperature was 270±3℃ and pressure was 7.3 MPa. It's primary crystalline size was 20 nm and agglomerated as spherical shape whose size was 0.7∼1㎛. The powders prepared on sol-gel process were not sintered densely at 900℃ because of abnormal grain growth. However, the powders which prepared on supercritical fluid process were sintered densely at the comparatively low temperature of 800℃ by ideal growth of grain, which are fired at 900℃.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.06a
• /
• pp.281-282
• /
• 2007

$Mg_4Nb_2O_9$ (MN) ceramics have been prepared by a sol-gel method. The powder characteristics, phase evolution, and microwave dielectric properties of the MN were investigated in various processing conditions such as sol-gel compositions, calcination, and sintering temperatures. A Qxfo value of 111,717 GHz with a ${\varepsilon}_r$ of 10.59 and a ${\tau}_f$ of $+1.736\;ppm/^{\circ}C$ was obtained after sintering at $1300^{\circ}C$ for 5 h.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1999.11a
• /
• pp.290-293
• /
• 1999

(Ba$_{0.5}$Sr$_{0.5}$)TiO$_3$ thin films were fabricated at different RTA temperatures and thicknesses by Sol-Gel method. Solution consisting of acetate powders and titanium isopropoxide in a mixture of acetic acid and ethylene glycol were spin coated onto Pt/Ti/SiO$_2$/Si substrates. The films were annealed in the temperature range of 650~80$0^{\circ}C$ for 3 minutes by rapid thermal annealing. These BST thin films were fully crystallized at 75$0^{\circ}C$ and showed a maximum dielectric constant value of $\varepsilon$$_{r}$=~468 and dielectric loss was ~0.025 at a thickness of approximately 4000$\AA$.EX>.>.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2005.07a
• /
• pp.401-402
• /
• 2005

The important parts of material science in the film preparation fields and sol-gel technology are presented. For the present work, a series of amorphous films was prepared in air by sol-gel method without using some alkoxide stabilizer, which reduces the reactivity of the metal alkoxides. The choice of precursors can affect the chemical-reaction kinetics, microstructures and properties of the product. In this report author compared the crystallization behavior of oxide functional films derived from the same precursors, stressing the influence of experiment conditions and where it was possible to obtain the uniform amorphous or crystalline dielectric films. A short analysis of sol-gel technology and thin film methods about development of dielectric materials has been given.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.29 no.9
• /
• pp.527-531
• /
• 2016

In this study, p-type thin film transistors consisting of CuO channels were fabricated by sol-gel process, with copper (II) acetate monohydrate precursors. At $500^{\circ}C$, the deposited films were fully converted into monoclinic phase CuO. The fabricated CuO thin film transistors deliver field effect mobility in saturation regime of $0.015cm^2/Vs$, and $I_{on}/I_{off}$ of ${\sim}10^3$. The degradation of the performance of the fabricated CuO thin film transistor caused by the exposure to air has been studied.

• Korean Journal of Materials Research
• /
• v.16 no.10
• /
• pp.599-605
• /
• 2006

N-(3-triethoxysilylpropyl)-1,4-diaminoanthrquinone-2,3-dicarboximide (TESP-DADI), an organic blue pigment, has been prepared and incorporated into silica solid matrix reacting triethyl orthosilicate (TEOS) via sol-gel method. Morphology and microstructure of resulting hybrid pigment were studied employing SEM and TEM. The micrographs and particle size distributions showed that uniform pigment can be obtained employing TEOS-based sol-gel method forming silica core. Particle size distribution of dispersed pigment in water was examined using the technique of dynamic light scattering. The ensuing pigment dispersion ink was subjected to various physicochemical evaluation such as viscosity, surface tension, inkjet stability, storage stability, and color change as inkjet ink using spectrophotometric, and microscopic techniques.

• Journal of the Korean Ceramic Society
• /
• v.42 no.3 s.274
• /
• pp.165-170
• /
• 2005

Sol-gel methods offer many advantages over conventional slip-casting, including the ability to produce ceramic membranes. They are purer, more homogeneous, more reactive and contain a wider variety of compositions. We produced ormosil sol using sol-gel process under various molecular weight of polymer species[polyethylene glycol(PEG)] in total system [Tetraethyl ortho silicate(TEOS)-polyethylene glycol(PEG)]. The properties of as-prepared ormosil sol such as viscosity and gelation time are characterized. Also, the ceramic membrane was prepared by dip-coating with synthetic sol and its microstructure was observed by scanning electron microscopy. The permeability and rejection efficiency of membrane for oil/water emulsion were evaluated as cross­flow apparatus. The ormosil sol coated membrane was easily formed by steric effect of polymer and it improved flux efficiency because infiltration into porous support decreased. Its flux efficiency was elevated about $200\;l/m^2h$ compared with colloidal sol coated membrane at point of five minutes from starting test.