• Journal of the Korean Wood Science and Technology
• /
• 제31권3호
• /
• pp.35-41
• /
• 2003

The mechanical and physical properties of wood are strongly dependent upon the slope of grain. Specially, tensile strength is more severely affected by the slope of grain. Therefore, tension tests were performed on small thin wood samples made from Pinus radiata with varying the slope of grain. Determining the tensile strength for clear thin wood samples the other variabilities associated with material, size, drying, defects, etc were discarded. Slope of grain was measured by the slope of grain indicator and actual slope of grain was also determined by a protractor. Correlation coefficients between machine measured and actual slope of grain for 40 pieces of 2×20 mm, 300 mm long Pinus radiata were 0.84 for wide face measurement. Results also showed that tensile strength and MOE from stress wave tests decreased with increasing the slope of grain. This study did not establish a relationships for tensile strength and MOE from stress wave with slope of grain. However, the trends of MOEs from stress wave test with both slope of grain are agreed well with Hankinson's equation. Predicted tension strength curve by Hankinson's equation was also agreed well with the experimental data over the range from 0 to 13 degrees for slope of grain.

• Journal of the Korean Wood Science and Technology
• /
• 제21권3호
• /
• pp.45-52
• /
• 1993

Surveyed results on the slope of grain and the twist of sawn lumber of Pinus koraiensis, Larix leptolepis, and Pinus densiflora were summarized as follows: 1. The slope of grain of Pinus koraiensis has a Z-grain in the stem axis. The slope of grain was found to be the lowest at near to the pith and then constantly increased. At the height of 0.2m from the base of stem. a cross section of 35 annual rings was found to have a repeatedly increasing and decreasing slope of grain and then constantly decreased. At the height of 1.2m to 7.2m from the base of stem, the slope of grain increased conspicuously until the 10th annual ring, after which it increased near to the bark with repeatedly increasing and decreasing trends. 2. Pinus densiflora has a S-grain in the stem axis. The lowest slope of grain was found at near to the pith, and the highest in the 10 to 35 annual rings from the pith. 3. Larix leptolepis has a S-grain. At the height of 3.2m from the base of stem, the big fluctuation of the slope of grain was found without any particular trend. 4. The slope of grain and the twist between natural and reforested timber of Pinus koraiensis were found to be almost the same trend in viewpoint of the annual ring. The maximum slope of grain of imported Siberian timber of Pinus koraiensis was found at the 10 annual rings, which was quite similar to that of native species in Korea, but the big difference of the twist was found at 140 annual rings. 5. The twist was little at the mature wood of reforested Pinus koraiensis and Siberians and the duplicated part of mature and juvenile woods of those. On the contrary, the twist was great at the duplicated part of mature and juvenile woods of Pinus koraiensis. 6. The twist of Larix leptolepis showed the S-direction which coincided with that of slope of grain. The twist was greatest at the part of juvenile wood and little at the duplicated part of mature and juvenile woods, and little difference of twist was found between mature and juvenile woods. 7. Siberian larix having a minimum slope of grain showed the lowest twist, and the twist at the duplicated part of mature and juvenile woods showed a middle level of both mature and juvenile woods' portions.

• Journal of the Korean Wood Science and Technology
• /
• 제37권5호
• /
• pp.465-473
• /
• 2009

Three failure theories were studied to evaluate the wood strength variation with grain slope. Maximum stress theory, Tsai-Hill theory and Hankinson formula were presented to hypothesize the failure of wood according to grain slope to loading direction. Red pine and Japanese larch were used as materials to simulate failure strength prediction with grain slope. Calculation of strength results was that the strength of wood drops rapidly between parallel to grain orientation (0 degree) and 15 degree grain orientation. The strength of wood with grain orientation were somewhat different at small grain angles among failure theories, and this tendency was due to tension and compression distinction, and shear accounting in each theories. For the above 45 degree grain orientation, the predicted failure strength of wood with grain variation were very close in each failure theories and were useful in assessing failure strength of wood. The applicable these theories should be considered that the wood has different behavior in tension and compression, and this lead to different strength at small grain angles in each theories. Furthermore, reconsideration is needed to assess the failure strength of wood at small grain angles in Hankinson formula and further studies are necessary to accounting for shear behavior at small grain angles.

• 한국농공학회논문집
• /
• 제55권6호
• /
• pp.127-133
• /
• 2013

The purpose of this study was to investigate maximum and minimum grain size which eroded by wind according to soil and wind conditions, such as top soil water content, roughness, land slope, wind velocity and proportion of grain size under 0.84mm. For performing this study, portable wind erosion tunnel was designed and utilized during field test, which facilitated measuring actual wind erosions under artificially controlled wind conditions. In the result, maximum, minimum grain size had strong negative correlation with roughness while weak positive correlation with wind velocity. Also, Slope which means the effect of gravity also influence grain size erodible by winds. Based on these results, regression equations were suggested for predicting maximum and minimum grain sizes by using multiple linear regression analysis from SPSS 20.0. The equation for maximum grain size erodible by winds showed a good agreement with the observed data with $R^2$=0.896. Other equation for minimum grain size had $R^2$=0.777.

• 한국수자원학회논문집
• /
• 제51권4호
• /
• pp.313-322
• /
• 2018

Step의 높이는 하상재료 입경의 크기와 거의 같은 상관관계가 있으며, 하도경사에 따라 증가하고, 하도 폭과 step 파장은 거의 같은 크기로서 하도경사가 증가하면 step 파장은 감소하는 것으로 분석되었다. 하도 폭과 step 폭은 뚜렷한 상관관계가 있으며, 하도 폭의 증가에 따라 step 폭도 증가하는 것으로 분석되었다. 또한, step 파장은 하도 폭에 의하여 규모가 정해지고, step 높이는 step을 형성하는 암석의 크기에 의해 지배되기 때문에 step-pool의 종단면의 하상구조는 하도경사에 따라 변화하는 것으로 판단된다. Pool의 규모는 하도 폭, 입경 및 하도경사와 상관성이 큰 것을 확인하였다. 따라서 하천의 step-pool 구조 특성은 다양한 인자들의 영향을 받지만 대표적으로 입경, 하도 폭 및 하도경사로서 설명할 수 있는 것으로 분석되었다.

• 대한지리학회지
• /
• 제33권1호
• /
• pp.1-16
• /
• 1998

본 논문에서는 조립질 하상이 잘 발달된 로키 산맥의 소하천들을 대상으로 퇴적물의 입경과 유역 면적과의 관계, 그리고 퇴적물의 입경과 하도 경사와의 관계를 중점적으로 조사하였다. 조사 결과, 퇴적물의 입경은 유역 면적의 증대에 따라 지수적으로 감소되었으며, 산지와 평지의 지형 경계부를 기점으로 그의 상류와 하류간에 입경 변화의 경향성이 서로 달랐다. 하도 경사 또한 유역 면적의 증대에 따라 지수적으로 감소되었는데, 그 분포 패턴은 퇴적물 입경의 경우와 큰 차이가 없었다. 따라서 퇴적물 입경과 하도 경사는 매우 밀접한 관련이 있는 것으로 조사되었다. 이와 같은 조사 결과들을 유역 분지의 지형 및 지질 조건과 관련지어 고찰하여 볼 때, 본 지역에서는 높은 산지로부터 낮은 평지로 급격히 전환되는 지형 조건과 비교적 동질적인 지질 조건이 퇴적물의 입경 및 하도 경사에 영향을 미치고 있는 것으로 생각된다.

• 한국분말재료학회지
• /
• 제6권1호
• /
• pp.81-87
• /
• 1999

Based on the pore filling theory, the microstructure evolution during liquid-phase sintering has been analyzed in terms of interrelationship between average grain size and relative density. For constant liquid volume fraction, the microsturucture trajectories reduced to a single curve in a grain size(x)-density(y) map, regardless of grain growth constant. The slope of curves in the map was inversely proportional to average pore size, while it increased fapidly with liquid volume fraction. Increase in pore volume fraction retarded the densification considerably, but showed marginal effect on the slope. The activation energy of densification was predicted to be the same as that of grain growth as long as the liquid volume fraction is constant for any temperature range studied. The present analyses on microstricture evolution may demonstrate the usefulness of pore filling theory and provide a guideline for process optimization of liquid-phase sintering.

• Journal of the Korean Wood Science and Technology
• /
• 제28권2호
• /
• pp.10-18
• /
• 2000

초음파를 이용한 목재의 비파괴시험은 등급구분 수분 및 결점 탐지, 썩은 정도 평가 등의 용도에 적용되고 있다. 이와 같은 기술을 실제로 적용하기 위해서는 목재 내의 초음파 전달과 목재의 성질 사이의 관계에 대한 기본적인 연구가 선행되어야 한다. 이 연구에서는 함수율과 섬유경사각이 초음파 전달 속도에 미치는 영향을 분석하기 위하여 낙엽송과 소나무를 대상으로 초음파 비파괴시험을 실시하였다. 함수율에 대한 시험을 위한 시험편은 생재상태, 30%, 20%, 10% 및 전건상태의 함수율을 갖도록 준비하였고 섬유경사각에 대한 시험을 위해서는 접선방향으로 0, 15, 30, 45, 60, 75 및 90도의 섬유경사각을 갖는 시험편을 준비하였다. 초음파 전달 속도는 섬유포화점에 근사한 30% 이하의 낮은 함수율 범위에서는 함수율에 반비례하였으며 이보다 높은 함수율 범위에서는 함수율에 관계없이 일정한 경향을 나타내었다. 목재의 압축강도와 함수율 사이의 관계에서도 이와 유사한 경향이 관찰되었다. 목재의 섬유경사각도 초음파 전달 속도 및 압축강도와 반비례하는 경향을 나타내었다. 압축강도와 초음파 전달 속도 사이의 관계는 정비례하는 관계로서 하나의 직선식으로 나타낼 수 있었다.

• The Korean Journal of Ceramics
• /
• 제4권2호
• /
• pp.122-127
• /
• 1998

Conductivities of polycrystalline ceria doped with several rare earth oxides were measured by AC admittance and DC four probe method. The conductions were separated into grain and grain boundary contributions using the complex admittance technique as well as grain size dependence of conductivity. The grain size dependence of polycrystalline conductivity, which can be adequately described by the so-called brick layer model, appears to give a more reliable measure of the grain conductivity compared to the complex admittance method. Polycrystalline resistivity(1/conductivity) increases linearly with the reciprocal of grain size. The intercept of resistivity vs. inverse grain size plot gives a measure of the grain resistivity and the slope gives a measure of the grain boundary resistivity. It was also noted that errors involved in the analysis of experimental data may be different between the complex admittance method and the impedance method. A greater resolution of the spectra was found in the complex admittance method, insofar as the present work is concerned, suggesting that the commonly used equivalent circuit may require re-evaluation.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2001년도 춘계학술대회 논문집
• /
• pp.143-146
• /
• 2001

The evolution of dynamic recrystallization (DRX) was studied with torsion test for AISI 304 stainless steel in the temperature range of $900-1000^{\circ}C$ and strain rate range of 0.05-5/sec. The evolution of DRX was investigated with microstructural analysis and change of flow stress curve slope. The investigation of serrated grain boundaries using electron back scattered diffraction (EBSD) analysis indicated that the nucleated new DRX grain size was similar to the size of bulging part. Before the steady state, the dynamically recrystallizing grains do not remain a constant size and gradually grow to the size of fully DRX grain at steady state. The calculation of grain size was based on $X_{DRX}$ and the assumption, which the nucleated DRX grains are growing to the steady state, continuously. It was found that the calculated results agreed with the microstructure of the alloy.