• Tribology and Lubricants
• /
• v.11 no.5
• /
• pp.20-25
• /
• 1995

Diamond films were prepared by a hot filament vapor deposition onto polycrystal silicon nitride substrates. Different kinds of silicon nitride containing CaO and $Fe_{2}O_{3}$ were manufactured to investigate the impurity effect of substrate on the morphology of diamond films and their wear behaviors. Nucleation rates and morphologies of diamond films deposited on various kinds of silicon nitride were compared. The highest nucleation rate was observed in a substrate containing 1% of CaO. Wear tests were performed with a silicon nitride ball on the disk geometry to investigate the tribological behavior of diamond film against silicon nitride. This study demonstrated that different morphologies of diamond film due to substrate impurities produced different wear behavior against silicon nitride.

• Journal of the Semiconductor & Display Technology
• /
• v.18 no.4
• /
• pp.12-17
• /
• 2019

In this study, the Ag nano-dots structure and silicon nitride film were applied to the textured wafer surface to improve the light trapping effect of mono-crystalline silicon solar cell. Ag nano-dots structure was formed by performing a heat treatment for 30 minutes at 650℃ after the deposition of 10nm Ag thin film. Ag thin film deposition was performed using a thermal evaporator. The silicon nitride film was deposited by a Hot-wire chemical vapor deposition. The effect of light trapping was compared and analyzed through light reflectance measurements. Experimental results showed that the reflectivity increased by 0.5 ~ 1% under all nitride thickness conditions when Ag nano-dots structure was formed before nitride film deposition. In addition, when the Ag nano-dots structure is formed after deposition of the silicon nitride film, the reflectance is increased in the nitride film condition of 70 nm or more. When the HF treatment was performed for 60 seconds to improve the Ag nano-dot structure, the overall reflectance was improved, and the reflectance was 0.15% lower than that of the silicon nitride film-only sample at 90 nm silicon nitride film condition.

• Journal of the Korean Ceramic Society
• /
• v.42 no.5 s.276
• /
• pp.359-365
• /
• 2005

Silicon nitride coating films with various ratios of nitrogen to silicon contents were prepared and characterized. The film was coated on silicon substrate by sputtering method with changing nitrogen gas flow rate in a chamber. The nitrogen to silicon ratio was found to have values in a range from 0 to 1.4. Coated film was characterized with scanning electron microscopy, transmission electron microscopy, electron probe microanalysis, nanoindentation scanning probe microscopy, x-ray photon spectrometry, and Raman spectrometry. Silicon nitride phase in all samples showed amorphous nature regardless of N/Si ratio. When N/Si ratio was 1.25, hardness and elastic modulus of silicon nitride film showed maximum with 22 GPa and 210 GPa, respectively. Those values decreased, when N/Si ratio was higher than 1.25. Raman spectrum showed that no silicon phase exist in the film. XPS result showed that the silicon-nitrogen bond was dominant way for atomic bonding in the film. The structure and property was explained with Random Bonding Model(RBM) which was consistent with the microstructure and chemistry analysis for the coating films.

• 한국신재생에너지학회:학술대회논문집
• /
• 2010.11a
• /
• pp.56.1-56.1
• /
• 2010

결정질 실리콘 태양전지의 표면 ARC(Anti-reflection Coating)layer는 반사도를 줄여 광 흡수율을 증가시키고, passivation 효과를 통하여 표면 재결합을 감소 시켜 태양전지의 효율을 높이는 중요한 역할을 한다. Silicon nitride 박막은 외부 stress 요인에 대해 안정성을 담보할 수 있어야한다. 따라서, 본 연구에서는 굴절률 가변에 따른 silicon nitride 박막을 PECVD를 이용하여 증착하고, 항온/항습 stability test를 통해 박막의 안정성을 확인하였다. Silicon nitride 증착을 위해 PECVD를 이용하였고, 공정압력 0.8Torr, 증착온도 $450^{\circ}C$, 증착파워 300W에서 실험을 진행하였다 박막의 굴절률은 1.9~2.3의 범위로 가변하였다. 항온/항습에 대한 신뢰성을 test 하기 위하여 5시간동안의 test를 1cycle로 하여 20회 동안 실험을 실시하였다. 증착된 silicon nitride 박막의 lifetime은 firing 이후 57.8us로 가장 높았으며, 항온/항습 test 이후에도 유사한 경향을 확인 할 수 있었다. 또한, 100h 동안의 항온/항습 test 결과 silicon nitride 박막의 lifetme 감소는 8.5%에 불과했다. 본 연구를 통하여 온도와 습도의 변화에 따른 결정질 실리콘 태양전지의 SiNx 박막의 증착 공정 조건에 대한 신뢰성을 확인 할 수 있었다.

• Journal of Sensor Science and Technology
• /
• v.14 no.5
• /
• pp.357-361
• /
• 2005

Low-stress silicon nitride (LSN) thin films with embedded metal line have been developed as free standing structures to keep microspheres in proper locations and localized heat source for application to a chip-based sensor array for the simultaneous and near-real-time detection of multiple analytes in solution. The LSN film has been utilized as a structural material as well as a hard mask layer for wet anisotropic etching of silicon. The LSN was deposited by LPCVD (Low Pressure Chemical Vapor Deposition) process by varing the ratio of source gas flows. The residual stress of the LSN film was measured by laser curvature method. The residual stress of the LSN film is 6 times lower than that of the stoichiometric silicon nitride film. The test results showed that not only the LSN film but also the stack of LSN layers with embedded metal line could stand without notable deflection.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2008.10a
• /
• pp.218-221
• /
• 2008

Bottom-gate microcrystalline silicon thin film transistors (${\mu}c$-Si:H TFTs) were fabricated on glass and transparent polyimide substrates by conventional 13.56 MHz RF plasma enhanced chemical vapor deposition at $200^{\circ}C$. The deposition rate of the ${\mu}c$-Si:H film is 24 nm/min and the amorphous incubation layer near the ${\mu}c$-Si:H/silicon nitride interface is unobvious. The threshold voltage of ${\mu}c$-Si:H TFTs can be improved by $H_2$ or $NH_3$ plasma pretreatment silicon nitride film.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.55 no.12
• /
• pp.565-569
• /
• 2006

Plasma enhanced chemical vapor deposition(PECVD) is a well established technique for the deposition of hydrogenated film of silicon nitride (SiNx:H), which is commonly used as an antireflection coating as well as passivating layer in crystalline silicon solar cell. PECVD-SiNx:H films were investigated by varying the deposition and annealing conditions to optimize for the application in silicon solar cells. By varying the gas ratio (ammonia to silane), the silicon nitride films of refractive indices 1.85 - 2.45 were obtained. The film deposited at $450^{\circ}C$ showed the best carrier lifetime through the film deposition rate was not encouraging. The film deposited with the gas ratio of 0.57 showed the best carrier lifetime after annealing at a temperature of $800^{\circ}C$. The single crystalline silicon solar cells fabricated in conventional industrial production line applying the optimized film deposition and annealing conditions on large area substrate of size $125mm{\times}125mm$ (pseudo square) was found to have the conversion efficiencies as high as 17.05 %. Low cost and high efficiency silicon solar cells fabrication sequence has also been explained in this paper.

• The Korean Journal of Ceramics
• /
• v.4 no.3
• /
• pp.222-226
• /
• 1998

$Cu_3N$ film deposited on silicon oxide substrate by r.f. reactive sputtering technique. Synthesis and properties of copper nitride film were investigated for its possible application to Cu metallization as adhesive interlayer between copper and $SiO_2. Cu_3N$ film was synthesized at the substrate temperature ranging from $100^{\circ}C$ to $200^{\circ}C$ and at nitrogen gas ratio above $X_{N2}=0.4. Cu_3N, CuN_x$, and FGM-structured $Cu/CuN_x$ films prepared in this work passed Scotch-tape test and showed improved adhesion property to silicon oxide substrate compared with Cu film. Electrical resistivity of copper nitride film had a dependency on its lattice constant and was ranged from 10-7 to 10-1 $\Omega$cm. Copper nitride film was, however, unstable when it was annealed at the temperature above $400^{\circ}C$.

• Transactions on Electrical and Electronic Materials
• /
• v.9 no.6
• /
• pp.231-236
• /
• 2008

B, P, and Cs ions were implanted with various parameters into silicon nitride layers prepared by LPCVD. In order to get the maximum impurity concentration at the silicon nitride surface, a high temperature oxide (HTO) buffer layers was deposited prior to the implantation. Alkali ion and pH sensing properties of the layers were investigated with an electrolyte-insulator-silicon (EIS) structure using high frequency capacitance-voltage (HF-CV) measurements. The ion sensing properties of implanted silicon nitrides were compared to those of as-deposited silicon nitride. Band Cs co-implanted silicon nitrides showed a pronounced difference in pH and alkali ion sensing properties compared to those of as-deposited silicon nitride. B or P implanted silicon nitrides in contrast showed similar ion sensitivities like those of as-deposited silicon nitride.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.19 no.6
• /
• pp.531-537
• /
• 2006

A micromachined piezoelectric microspeaker was fabricated with a highly c-axis oriented ZnO thin film on a silicon-nitride film having compressive residual stress. When it was measured 3 mm away from the microspeaker in open field, the largest sound pressure level produced by the fabricated microspeaker was about 91 dB at around 2.9 kHz for the applied voltage of $6\;V_{peak-to-peak}$. The key technologies to these successful results were as follows: (1) the usage of a wrinkled diaphragm caused by the high compressive residual stress of silicon-nitride thin film, (2) the usage of the highly c-axis oriented ZnO thin film.