• Journal of Power Electronics
• /
• 제9권5호
• /
• pp.757-771
• /
• 2009

This paper proposes a systematic approach to the modeling of the small-signal characteristics of three-phase bridge boost rectifiers under non-sinusoidal conditions. The main obstacle to the conventional synchronous d-q frame modeling approach is that it is unable to identify a steady-state under non-sinusoidal conditions. However, for most applications under non-sinusoidal conditions, the current loops of boost rectifiers are designed to have a bandwidth that is much higher than typical harmonics frequencies in order to achieve good current control for these harmonic components. Therefore a quasi-static method is applied to the proposed modeling approach. The converter small-signal characteristics developed from conventional synchronous frame modeling under different operating points are investigated and a worst case point is then located for the current loop design. Both qualitative and quantitative analyses are presented. It is observed that operating points influence the converter low frequency characteristics but hardly affect the dominant poles. The relationship between power stage parameters, system poles and zeroes is also presented which offers good support for the system design. Both the simulation and experimental results verified the analysis and proposed modeling approach. Finally, the practical case of a parallel active power filter is studied to present the modeling approach and the resultant regulator design procedure. The system performance further verifies the whole analysis.

• Journal of Positioning, Navigation, and Timing
• /
• 제9권3호
• /
• pp.157-167
• /
• 2020

Fingerprinting method is useful when estimating the location of a requestor based on LTE signals in an urban area. To do this, it is necessary to acquire location-based signals everywhere in the service area for fingerprint DB generation in advance. However, there may be signal uncollected area within a wide service area, which may cause a problem that the positioning accuracy of the requestor is low. In order to solve this problem, in this paper, signal propagation modeling is performed based on the obtained measurements, and based on this model, the signal information in the non-acquisition region is estimated. To this end, techniques for modeling signal propagation according to a method using measurements are proposed. The performance of the proposed techniques is verified based on the measurements obtained on a test bed selected as Seocho-gu, Seoul. As a result, it can be seen that signal propagation modeling performed based on multidivision segmented measurements has the most performance improvement.

• 한국음향학회지
• /
• 제19권4호
• /
• pp.58-68
• /
• 2000

본 논문에서는 폴리포닉 오디오 신호에 대한 정현파 모델링 방법을 제안한다. 정현화 모델링을 폴리포닉 오디오 신호에 적용하는데 있어서 가장 큰 문제점은 스펙트럼 분석을 위한 분석 윈도우의 크기를 결정할 수 없다는 것이다. 또한 고음질의 합성음을 위해서는 악기음의 특성을 결정짓는 어택이 잘 보존되어야 한다. 본 논문에서는 입력 신호를 6개의 옥타브 벤드 구조의 다중 해상도 필터 뱅크를 통과시키고, 각 서브벤드 신호에 대해 서로 다른 크기의 분석 윈도우를 적용시킴으로써 폴리포닉 오디오 신호에 대한 분석 윈도우 크기 결정 문제를 해결한다. 정현파 모델링에서 발생하는 어택과 같은 천이 구간에서의 퍼짐 현상을 개선하기 위해 각 서브밴드 신호에 동적 세그맨테이션 방법을 적용하여 천이 구간 근처에서는 분석과 합성 프레임 크기를 작게 하는 방법을 사용한다. 이 방법을 통해 서브밴드 신호의 구간별 시간-주파수 특성에 따라 적절한 크기의 윈도우를 선택할 수 있다. 동적 세그멘테이션 방법으로는 기존의 방법보다 계산량과 성능 면에서 더 나은 특성을 보이는 방법을 제안한다. 여러가지 폴리포닉 오디오 신호에 대한 시뮬레이션 결과 제안한 정현파 모델링 방법이 음질의 손상 없이 원래 신호를 잘 복원할 수 있음을 확인하였다.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2006년 학술대회 논문집 정보 및 제어부문
• /
• pp.600-602
• /
• 2006

Some abnormal signals diagnostics and analysis through an important equivalent circuits modeling for passive elements under severe accident conditions have been performed. Unlike the design basis accidents, there are inherently some uncertainties in the instrumentation capabilities under the accident conditions. So, the circuit simulation analysis and diagnosis methods are used to assess instruments in detail when they give apparently abnormal readings as an accident alternative method. The simulations can be useful to investigate what the signal and circuit characteristics would be when similar to a variety of symptoms that can result from the environmental conditions such as high temperature, humidity, and pressure condition. In this paper, a new simulator through an analysis of the important equivalent circuits modeling under temperature accident conditions has been designed, the designed simulator is composed of the LabVIEW code as a main tool and the out-put file of the Multi-SIM code as an engine tool is exported to in-put file of the LabVIEW code. The procedure for the simulator design was divided into two design steps, of which the first step was the diagnosis method, the second step was the circuit simulator for the signal processing tool. It has three main functions which are a signal processing tool, an accident management tool, and an additional guide from the initial screen. This simulator should be possible that it could be applied a output signal analysis to some transient signal by variation of the resistance passive elements in the R-L-C equivalent circuit modeling under various degraded conditions in NPPs.

• 대한기계학회논문집A
• /
• 제21권2호
• /
• pp.281-287
• /
• 1997

In the conventional inverse modeling method for on-line modeling of the secondary path transfer function, the signal to noise ratio between the arbitrary random signal and the plant noise have to keep at -10 - -20 dB. For these reasons, the modeling can't be exactly implemented by the conventional method alone and the convergence time for modeling becomes too long. In this study, by combining the conventional inverse modeling method with an adaptive line enhancer, or with an adaptive noise canceller, a rigorous transfer functions of secondary path modeling and the control of a primary noise have been implemented simultaneously.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2001년도 하계종합학술대회 논문집(2)
• /
• pp.217-220
• /
• 2001

Modified Materka-Kacprzak 대신호 MODFET(modulation-doped field-effect transistor) model을 사용하여 GaN(gallium nitride) MODFET 대신호 모델링을 수행하였다. Dambrine(3)이 제안한 방법에 따라 45㎒에서 40㎒의 주파수 범위에 걸쳐 S-parameter 및 DC특성을 측정하였으며, 측정결과를 토대로 cold FET 방법［4］에 의해 측정된 기생성분들을 de-embedding 함으로써 소신호 파라미터를 추출하였고, 추출된 소신호 파라미터는 함수를 사용하여 측정결과를 재현하는 맞춤함수 모델의 일종인 modified Materka 모델을 사용하여 모델링하였다. 수행된 대신호 모델링을 검증하기 위하여 모델링된 GaN MODFET의 DC 및 S-파라미터, 전력특성을 측정값과 각각 비교해 보았을 때 비교적 일치하고 있음을 보여서 GaN 대신호 모델링을 검증하였으며, modified Materka 모델이 GaN MODFET 대신호 모델링에 유용하게 사용될 수 있음을 보였다.

• 항공우주기술
• /
• 제7권2호
• /
• pp.82-87
• /
• 2008

본 연구에서는 우주에서 가시광 영역으로 지구의 지표면을 고해상도로 촬영하는 위성탑재카메라를 위한 복사에너지 신호량을 모델링하였다. 복사에너지 모델링은 광원으로서의 태양과 지구대기 및 지표면 반사도, 카메라의 특성 등을 포함하며 최종 계산 결과는 광전자카메라의 광검지기에서 생성되는 전자의 수로 나타난다.

• 한국정보통신학회논문지
• /
• 제7권4호
• /
• pp.743-749
• /
• 2003

본 논문에서는, cold-HEMT의 게이트에 핀치오프 전압보다 약간 낮은 전압을 가함으로써 게이트 손상문제로부터 자유로우며 부가적인 DC 측정을 필요로 하지 않는 새로운 HEMT 소신호 모델링 방법을 제시한다. 제시된 방법에 의해서 모델링된 회로의 S-파라미터 이론치는 49개의 동작 바이어스점에서 측정치와 62GHz까지 뛰어난 일치를 보였다.

• Journal of Positioning, Navigation, and Timing
• /
• 제8권4호
• /
• pp.193-200
• /
• 2019

The auto-encoder network which is a good candidate to handle the modeling of the signal strength attenuation is designed for denoising and compensating the distortion of the received data. It provides a non-linear mapping function by iteratively learning the encoder and the decoder. The encoder is the non-linear mapping function, and the decoder demands accurate data reconstruction from the representation generated by the encoder. In addition, the adaptive network width which supports the automatic generation of new hidden nodes and pruning of inconsequential nodes is also implemented in the proposed algorithm for increasing the efficiency of the algorithm. Simulation results show that the proposed method can improve the neural network training surface to achieve the highest possible accuracy of the signal modeling compared with the conventional modeling method.

• 한국통신학회논문지
• /
• 제21권5호
• /
• pp.1274-1282
• /
• 1996

This paper deals with an inverse modeling of nonminimum phase communication channel utilizing the HOS (High Order Statistics) of the received signal. After the communication channel is separated into the minimum phase and maximum phase components, the inverse modeling is performed independently. The performance superiority is confirmed by monte-carlo computer simulation in comparison with the traditional CMA (Constant Modulus Algorithm) method. By utilizing the proposed algorithm employing the HOS of the received signal, the inverse frequency characteristics of the channel can be obtained withoug transmitted signal in digital communication. This algorithm is required in preprocessing or postprocessing in order to remove the channel effect, and effective in the self adaptive equalizer which can minimize the bit error rate or symbol error rate in the recovry of received signal.