• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.23 no.11
• /
• pp.1239-1247
• /
• 2012

In this paper, design and fabrication of solid state power amplifier(SSPA) using GaN HEMT chip for X-band frequency are presented. The SSPA consists of the power supply for stable power and the control unit for communication and controlling the internal module, the RF Part to amplify RF signal, In particular the adopted active device for the RF Parts is GaN HEMT Bare chip of TriQuint company, the RF parts consists of pre-stage, drive-stage, main power-stage and each amplifier is designed with input and out matching circuit. The developed power amplifier demonstrated more than 300 W peak output power in condition of 26 % duty, max. pulse width 100us for the X-band frequency( 500 MHz bandwidth) and can apply to marine radar systems.

• Proceedings of the IEEK Conference
• /
• 2006.06a
• /
• pp.623-624
• /
• 2006

In this paper, we introduce the design and fabrication of V-band power amplifier MMIC with excellent gain-flatness for IEEE 802.15.3c WPAN system. The V-band power amplifier was designed using ETRI' $0.12{\mu}m$ PHEMT process. The PHEMT shows a peak transconductance ($G_{m,peak}$) of 500 mS/mm, a threshold voltage of -1.2 V, and a drain saturation current of 49 mA for 2 fingers and $100{\mu}m$ total gate width (2f100) at $V_{ds}$=2 V. The RF characteristics of the PHEMT show a cutoff frequency, $f_T$, of 97 GHz, and a maximum oscillation frequency, $f_{max}$, of 166 GHz. The gains of the each stages of the amplifier were modified to have broadband characteristics of input/output matching for first and fourth stages and get more gains of edge regions of operating frequency range for second and third stages in order to make the gain-flatness of the amplifier excellently for wide band. The performances of the fabricated 60 GHz power amplifier MMIC are operating frequency of $56.25{\sim}62.25\;GHz$, bandwidth of 6 GHz, small signal gain ($S_{21}$) of $16.5{\sim}17.2\;dB$, gain flatness of 0.7 dB, an input reflection coefficient ($S_{11}$) of $-16{\sim}-9\;dB$, output reflection coefficient ($S_{22}$) of $-16{\sim}-4\;dB$ and output power ($P_{out}$) of 13 dBm. The chip size of the amplifier MMIC was $3.7{\times}1.4mm^2$.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.48 no.2
• /
• pp.61-66
• /
• 2011

A new via structure on printed circuit board has been proposed for differential signaling in applications of high-speed interconnection. In new structure, the via is physically separated and then divided into two electrically-isolated sections using mechanical drill routing process. These cutted vias are connected respectively to the traces of the differential pair. New via structure makes possible to rout the differential pair using only one via, while conventional via structure needs two vias for interconnection. Because the spacing even in via region keeps almost constant, new via structure can alleviate an impedance discontinuity and then enhance its signal transmission characteristics such as reflection loss and insertion loss. It is expected that new via structure is effective in differential signaling for high-speed interconnection.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.45 no.8
• /
• pp.35-40
• /
• 2008

This paper proposes a dual-band balun which is based on Wilkinson power divider. By inserting $\lambda/2$ transmission line between port 2 and 3, this balun shows good matching at all ports and improved isolation. We use matamaterial(CRLH, D-CRLH) structure for a miniaturization of the circuit implementation and dual-band operation at TDMB frequency range(195MHz) and DVB-H frequency range(670MHz). The proposed balun is designed with return loss larger than -12.98dB at all port, and isolation larger than -12.4dB, the amplitude imbalance between output signals less than 0.08dB, also phase differences of outputs less than $2.8^{\circ}$.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.32 no.1C
• /
• pp.23-33
• /
• 2007

Video compression is essential technique for fast and efficient transmission of a large amount of video data maintaining high quality. Also, motion estimation and motion compensation is most important technique for efficient video compression. A proposed method is improved diamond search method which uses split diamond pattern and rotated diamond pattern. In particular, the proposed method shows superb result when it is used for the sequence with a direction of camera moving. Moreover when it is used for the sequence with little motion, complexity is reduced considerably by using fewer search points. Also, by varying the number of initial search points, the propose method can provide several options in terms of duality or speed. Simulation results shows that the proposed method sustains better visual quality compared with diamond search method and HEXBS even by using fewer search points. Besides, compared with existing methods, it is able to conduct a motion estimation more efficiently by changing the number of search points adaptively according to motion of video data.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.8 no.5
• /
• pp.1000-1006
• /
• 2007

This paper presents a power detector circuit which monitors the transmitting power for the application in CDMA cell phones. The proposed power detector are composed of coupler for coupling output power and detector fur monitoring output power. The designed coupler has low loss characteristic because it adopts the stripline structure which consists of two ground planes at both sides of signal plane. The design frequency is 824-849MHz which is the Tx band fur CDMA mobile terminal, and the coupling factor of the stripline coupler is -20dB. A schottky barrier diode is adopted for detector design because of its high speed operation with minimized loss. The required impedance matching is performed to improve the linearity and sensitivity of output voltage at relatively low detector input level where the nonlinear characteristic of diode exists. The package parasitics as well as intrinsic diode model are considered for simulation of the detector. The predicted performances agree well with the measured results.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.10 no.8
• /
• pp.1817-1823
• /
• 2009

A design of cascaded distributed amplifier with a broadband amplification is described in this paper. A medium power device with 23dBm, max output power under the optimal narrow-band power matching condition is adopted for the design and fabrication of the cascaded distributed amplifier. In general, conventional distributed amplifiers with the parallel connected input ports have a low gain, and previous cascaded distributed amplifiers show a relatively low output power of 10dBm at most, which is the upper limit of small signal amplification. However, the cascaded distributed amplifier in this paper shows the gain of $18.15{\pm}0.75dB$ and output power of 20dBm over $300MHz{\sim}2GHz$ from the measurement, so it can be well adopted as a wideband driver amplifier.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.46 no.2
• /
• pp.173-183
• /
• 2010

In a split beam echo sounder, the transducer design needs to have minimal side lobes because the angular position and level of the side lobes establishes the usable signal level and phase angle limits for determining target strength. In order to suppress effectively the generation of unwanted side lobes in the directivity pattern of split beam transducer, the spacing and size of the transducer elements need to be controlled less than half of a wavelength. With this purpose, a 50 kHz tonpilz type transducer with a half-wavelength diameter in relation to the development of a split beam transducer was designed using the equivalent circuit model, and the underwater performance characteristics were measured and analyzed. From the in-air and in-water impedance responses, the measured value of the electro-acoustic conversion efficiency for the designed transducer was 51.6%. A maximum transmitting voltage response (TVR) value of 172.25dB re $1{\mu}Pa/V$ at 1m was achieved at 52.92kHz with a specially designed matching network and the quality factor was 10.3 with the transmitting bandwidth of 5.14kHz. A maximum receiving sensitivity (SRT) of -183.57dB re $1V/{\mu}Pa$ was measured at 51.45kHz and the receiving bandwidth at -3dB was 1.71kHz. These results suggest that the designed tonpilz type transducer can be effectively used in the development of a split beam transducer for a 50kHz fish sizing echo sounder.

• Journal of Biosystems Engineering
• /
• v.43 no.4
• /
• pp.273-284
• /
• 2018

Purpose: Conventional headland turning typically requires repeated forward and backward movements to move the farming equipment to the next row. This research focuses on developing an upland agricultural robot with an optimized headland turning mechanism that enables a $180^{\circ}$ turning positioning to the next row in one steering motion designed for a two-wheel steering, four-wheel drive agricultural robot named the HADA-bot. The proposed steering mechanism allows for faster turnings at each headland compared to those of the conventional steering system. Methods: The HADA-bot was designed with 1.7-m wide wheel tracks to travel along the furrows of a garlic bed, and a look-ahead path following algorithm was applied using a real-time kinematic global positioning system signal. Pivot turning tests focused primarily on accuracy regarding the turning radius for the next path matching, saving headland turning time, area, and effort. Results: Several test cases were performed by evaluating right and left turns on two different surfaces: concrete and soil, at three speeds: 1, 2, and 3 km/h. From the left and right side pivot turning results, the percentage of lateral deviation is within the acceptable range of 10% even on the soil surface. This U-turn scheme reduces 67% and 54% of the headland turning time, and 36% and 32% of the required headland area compared to a 50 hp tractor (ISEKI, TA5240, Ehime, Japan) and a riding-type cultivator (CFM-1200, Asia Technology, Deagu, Rep. Korea), respectively. Conclusion: The pivot turning trajectory on both soil and concrete surfaces achieved similar results within the typical operating speed range. Overall, these results prove that the pivot turning mechanism is suitable for improving conventional headland turning by reducing both turning radius and turning time.

• Journal of Convergence for Information Technology
• /
• v.9 no.4
• /
• pp.14-20
• /
• 2019

The purpose of this paper is to present a smart QR code recording system and a method of non­storage data delivery that transforms the original data into a form of URL information by encrypting it and encoding the URL information into a QR code so that the QR code can be written and decrypted in a medium without storing the original data. The method of the study was presented by the prior art study and the literature research. Analysis results show that the system is built on the online administration server. The data input signal matching secret code is stored in DB, the QR code generation command converts input data from the password DB to the password information combined into the subordinate locator of the admin server's domain name, URL code. Therefore, the smart QR method of data management (recording and providing) indicates that there are no limitations in the ease and space of use or obstacles to capacity use.