• Journal of the Earthquake Engineering Society of Korea
• /
• v.14 no.1
• /
• pp.43-50
• /
• 2010

To address the problems caused by the corrosion of steel rebar, active research has recently been carried out on members where fiber-reinforced polymer (FRP) is used in place of rebar. As FRP bar is highly brittle and has a low modulus of elasticity, further research is needed on the evaluation of serviceability, in other words on the deflection of flexural concrete members reinforced with FRP rebars. Taking the reinforcement ratio as a variable, this paper analyzes the flexural capacity of concrete beams reinforced with CFRP rebar. The test results of specimens reinforced with CFRP rebar show an increase in stiffness and resisting force along with an increase in the reinforcement ratio. A reinforcement ratio of about 1.3 is needed for the member reinforced with CFRP rebar to show same section property of a steel member. Through a comparison for the value of an effective moment of inertia, the equation suggested by Bischoff & Scanlon predicted values closest to the actual results.

• The Journal of the Petrological Society of Korea
• /
• v.20 no.4
• /
• pp.219-230
• /
• 2011

Jurassic granite from Hapcheon was analysed with respect to the characteristics of the rock cleavage. The phases of distribution of microcracks were well evidenced from the enlarged photomicrographs(${\times}6.7$) of the thin section. The planes of principal set of microcracks are parallel to the rift plane and those of secondary set are parallel to the grain plane. These rift and grain microcracks are mutually near-perpendicular on the hardway planes. Consequently the rock cleavage of Jurassic granite from the studied quarry can be related to the preferred orientation of microcracks. Microcrack parameters such as number, length and density show an order of rift > grain > hardway. These results indicate a relative magnitude of the rock cleavage. Meanwhile, brazilian tensile strengths were measured with respect to the six directions. The results revealed a strong correlation between mechanical property with microcrack parameters.

• Fashion & Textile Research Journal
• /
• v.15 no.2
• /
• pp.309-315
• /
• 2013

This study examines the difference of surface properties according to napping characteristic of artificial suedes, measuring surface structure observation, the contact/non-contact method roughness, warm-cool feeling of touch, and subjective hand evaluation. Surface and cross-section observations showed a discernible difference in fineness, curl, length, mount of napping, and covering power of base fabric. The surface properties of artificial suede evaluated by KES-FB4 showed that the shorter napping length the more smooth surface and the roughness increased reciprocally with friction resistance and surface contour when the nap length reaches a high level. The surface roughness measuring system applied a laser displacement sensor by a non-contact method to assess napping characteristic and the base fabric and napping height. Surface roughness decreased when napping was uniformly covered with base fabric; however, the surface roughness increased specifically with the uneven covering power of the base fabric. For qmax of the suedes, those that had short and smaller amounts of napping increased; however, the napping of length and amount at some stage generated a low qmax value. The warm sensation in all suedes were strongly perceived, but the cool sensation of the perception was lower in the subjective evaluation. Smoothness and softness were perceived when the suede has a long and large amount napping; however, smoothness and hardness were perceived when the suede was short and with the uneven covering power.

• Journal of Korea Foundry Society
• /
• v.38 no.5
• /
• pp.87-94
• /
• 2018

The effects of Sr and (Ti-B) additives on the tensile properties of AC4A recycled (35% scrap content) aluminum alloys were investigated. An acicular morphology of the eutectic Si phase of as-cast specimens was converted to a fibrous morphology upon the addition of Sr. Moreover, morphology of the Sr modified eutectic Si phase became finer due to a T6 heat treatment. The grain size of the ${\alpha}$-solid solution was decreased by the addition of (Ti-B) additives. Depending on the treatment conditions of the as-cast specimens, i.e., no addition, a Sr addition and a (Ti-B)+Sr addition, the tensile strength levels of the as-cast specimens were 182, 192, and 204MPa, respectively. The corresponding strengths of T6 heat-treated specimens were 293, 308, and 318MPa. Elongations of the as-cast specimens were 2.2, 3.1, and 5.6%, and the corresponding elongations of the T6 heat-treated specimens were 4.6, 6.1, and 7.6%. The percentage of the reduced section area in the tensile specimens was also increased by the Sr and (Ti-B) additives. Sr and (Ti-B) additives changed the microstructure and the distribution of defects in the castings, resulting in an improvement of the tensile properties of AC4A aluminum alloys. According to our test results, recycled (35% scrap content) AC4A aluminum alloy met all of the KS requirements of the tensile strength and elongation values of AC4A aluminum alloy except for the elongation value of the one specimen condition, in this case the as-cast no-addition condition.

• Journal of Korean Society of Disaster and Security
• /
• v.12 no.4
• /
• pp.53-61
• /
• 2019

Occurrences of debris flow are a serious danger to roads and residential located in mountainous areas and cause a lot of property loss. In this study, two basins were selected and spatial data were constructed to simulate the occurred debris flow from mountainous areas. The first basin was to use the Terrestrial LiDAR to scan the debris flow occurrence section and to build terrain data. For the second basin, use drones the sediment in the basin was photographed and DSM (Digital surface model) was generated. And to analyze the effect of the occurrence of debris flow on downstream side, FLO-2D, two-dimensional commercial model, was used to simulate the flow region of the debris flow. And it was compared with the sedimentation area of terrestrial LiDAR and drone measurement data.

• Fire Science and Engineering
• /
• v.15 no.2
• /
• pp.1-5
• /
• 2001

We had investigated combustion properties of starch. Decomposition of starch scavenged by pre-cipitator of spinning factory with temperature were investigated using DSC and TGA. Combustion properties of starch according to amount were checked as temperature variation according to time using spontaneous ignition apparatus. Moreover, combustion properties with blowing or without blowing condition were checked in spontaneous ignition apparatus. As results of thermal analyses, increase in raising temperature causes initial smoldering temperature to move towards low temperature section. In addition, as amount of starch was increased, initial smoldering temperature was lowered. All of combustion forms were smoldering combustion. Initial smoldering temperature was low more slightly with blowing condition than without blowing condition in spontaneous ignition apparatus, which condition made heating value high.

• Journal of Powder Materials
• /
• v.14 no.6
• /
• pp.372-379
• /
• 2007

The microstructure, mechanical and electrochemical properties of plasma electrolytic coatings (PEO) coatings on Mg-4.3 wt%Zn-1.0 wt%Y and Mg-1.0 wt%Zn-2.0 wt%Y alloys prepared by gas atomization, followed by compaction at 320 for 10 min under the pressure of 700 MPa and sintering at 380 and 420 respectively for 24 h, were investigated, which was compared with the cast Mg-1.0 wt%Zn alloy. All coatings consisting of MgO and $Mg_2SiO_4$ oxides showed porous and coarse surface features with some volcano top-like pores distributed disorderly and cracks between pores. In particular, the surface of coatings on Mg-1.0 wt%Zn-2.0 wt%Y alloy showed smaller area of pores and cracks compared to the Mg-4.3 wt%Zn-1.0 wt%Y and Mg-1.0 wt%Zn alloys. The cross section micro-hardness of coatings on the gas atomized Mg-Zn-Y alloys was higher than that on the cast Mg-1.0 wt%Zn alloy. Additionally, the coated Mg-1.0 wt%Zn-2.0 wt%Y alloy exhibited the best corrosion resistance in 3.5%NaCl solution. It could be concluded that the addition of Y has a beneficial effect on the formation of protective and hard coatings on Mg alloys by plasma electrolytic oxidation treatment.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.23 no.4
• /
• pp.541-550
• /
• 2012

An improved method of moments using a hybrid Galerkin-interpolation technique for numerical analysis of electromagnetic wave scattering in the 3-dimensional space is presented in this paper. Basically, the EFIE(electric field integral equation) and RWG(Rao-Wilton-Glisson) basis function are used to compute a property of electromagnetic wave scattering. We propose a hybrid technique combining the existing Galerkin's method with the interpolation method to improve the efficiency of the numerical computation. Then, an index of relative distance of each cells was defined to distinguish the relatively far elements, which interpolation method can be applied. To verify the performance of the proposed technique, the analytical Mie-series solution was used to compute the theoretical RCS of a conducting sphere for the purpose of comparison. We also applied this hybrid technique to various scatterers such as trihedral/omni-directional corner-reflectors to analyze the radar backscattering properties.

• Restorative Dentistry and Endodontics
• /
• v.26 no.2
• /
• pp.111-120
• /
• 2001

Calcium hydroxide pastes is widely used in conventional endodontics. Along with the expanded clinical use of calcium hydroxide, literatures suggest mixing calcium hydroxide with other substance. Among added substances the vehicle plays the most importance role in the overall process because it is directly related with the velocity of ionic dissociation of $Ca^{2+}$ and OH ion. In this study, we evalutated and compared periapical tissue response and root resorption after canal was filled with mixture of saline and calcium hydroxide(Junsei Chemical Co.. Japan) as a aqueous vehicle, Metapaste(Meta Co., Korea) as a viscous vehicle paste, Vitapex(Neo Dental, Japan) as a oily vehicle paste and IRM(Caulk Dentsply, USA) in replantation of rat molar. A total of 31 maxillary first molars of Sprague-Dawley female rats, 30 days old were used. The upper 1st molar was extracted and the mesiobuccal canal was filled with mixture of saline and calcium hydroxide, Metapaste, Vitapex. IRM and then replanted. Rats were sacrificed 3 weeks after replantation. the maxillae were removed. section of 4 micron were cut and stained with hematoxylin-eosin, Apical tissue response were observed under light microscope. The results were as follows: 1. Saline mixing group and Metapaste group were significant different in fibrous capsule width compared to Vitapex group and IRM group(P<0.05). 2. Saline mixing group. Metapaste group. Vitapex group and IRM group did not prevent root resorption and there were no statistical difference. 3. In saline mixing group and Metapaste group. loss of pastes were observed in all samples. From the results of our study. we observed loss of pastes in saline mixing group and Metapaste group because of water soluble property and assumed it was related to inflammation in apical area and sealing ability of material. So, we should study and develop calcium hydroxide vehicle which is easily removed and more stable and because of only 3 weeks observation we need more evaluation in long period.

• Membrane Journal
• /
• v.17 no.4
• /
• pp.359-368
• /
• 2007

The copolymer membranes, poly(vinylidene fluoride-hexafluoropropylene) (PVdF-HFP) were prepared by phase inversion method using as an additive with N,N-dimethylformamid as a solvent. The pores are generated during the solvent and non-solvent exchange process in the coagulation bath filled with non-solvent (distilled water). The highest porosity of the membrane was 60%. The surface and cross-section of the membranes was observed with a scanning electron microscopy (SEM). The mechanical property of the membrane was determined by using an universal testing machine (UTM). Tensile strength of measured membranes is presented the maximum 6.57 MPa at 30 wt% of PVdF-HFP.