• The Journal of Advanced Prosthodontics
• /
• 제14권6호
• /
• pp.346-359
• /
• 2022

PURPOSE. Four and six implant-supported fixed full-arch prostheses with various framework materials were assessed under different loading conditions. MATERIALS AND METHODS. In the edentulous maxilla, the implants were positioned in a configuration of four to six implant modalities. CoCr, Ti, ZrO₂, and PEEK materials were used to produce the prosthetic structure. Using finite element stress analysis, the first molar was subjected to a 200 N axial and 45° oblique force. Stresses were measured on the bone, implants, abutment screw, abutment, and prosthetic screw. The Von Mises, maximum, and minimum principal stress values were calculated and compared. RESULTS. The maximum and minimum principal stresses in bone were determined as CoCr < ZrO₂ < Ti < PEEK. The Von Mises stresses on the implant, implant screw, abutment, and prosthetic screws were determined as CoCr < ZrO₂ < Ti < PEEK. The highest Von Mises stress was 9584.4 Mpa in PEEK material on the prosthetic screw under 4 implant-oblique loading. The highest maximum principal stress value in bone was found to be 120.89 Mpa, for PEEK in 4 implant-oblique loading. CONCLUSION. For four and six implant-supported structures, and depending on the loading condition, the system accumulated different stresses. The distribution of stress was reduced in materials with a high elastic modulus. When choosing materials for implant-supported fixed prostheses, it is essential to consider both the number of implants and the mechanical and physical attributes of the framework material.

• Elastomers and Composites
• /
• 제44권2호
• /
• pp.164-174
• /
• 2009

모듈라 치합형 동방향 이축 스크류식 압출기(modular intermeshing co-rotating twin screw extruder)를 이용하여 저온 내 충격성 향상을 위해 PA66/EPDM/PP-g-MA 및 PA66/EPDM-g-MA/PP-g-MA 복합체를 각 성분 wt%를 변화하여 제조하였다. 그 결과 이들 복합체 중에서 PA66/EPDM-g-MA/PP-g-MA의 wt%가 90/8/2인 복합체가 다른 복합체들 보다 열적, 기계적으로 우수한 결과를 나타내었다. 그리고 열중량분석기(Thermogravimetric Analysis), 시차주사열량계(Differential Scanning Calorimeter)를 이용하여 열적 특성, 주사 전자현미경(Scanning Electron Microcsopy)을 이용하여 형태학적 변화를 분석하였다. 본연구를 통하여 기존 PA66/EPDM composite의 단점인 낮은 계면력과 저온 내충격성을 향상 시켰으며, 최적의 mixing효과를 위한 screw configuration에 따른 압출 공정 확립과 PA66/EPDM composite 생산 공정 국산화 및 원가절감의 효과를 가져왔다.

• 한국정밀공학회지
• /
• 제22권7호
• /
• pp.191-199
• /
• 2005

Many researchers have been investigating the design of multi-mode absorption vibration absorber for multi degree-of-freedom (DOF) system. The approach taken to this problem has been to find the optimized constants of stiffness and damping for the given set of single-DOF absorbers or single multi-DOF absorber attached to a multi degree-of-freedom system. This paper presents a novel geometrical and direct design theory of a 6 DOF vibration absorber via screw theory. Theoretical development is demonstrated by a practical example in which the diagonal stiffness matrix is synthesized using rectangular configuration of springs. The performance of this absorber is simulated by modal analysis.

• Elastomers and Composites
• /
• 제39권2호
• /
• pp.131-141
• /
• 2004

본 연구에서는 폐기되는 고전압용 전선으로부터 얻어질 수 있는 XLPE(crosslinked polyethylene)의 재활용에 관하여 고찰하였다. XLPE 스크랩 및 폐기물의 분쇄를 위해 약 $100{\mu}m$ 이하부터 약 $1000{\mu}m$까지 입자크기의 조절이 가능한 두 종류의 분쇄기를 사용하였다. 모듈라 치합형 동방향회전 이축 스크류식 압출기(modular intermeshing co-rotating twin screw extruder)를 이용하여 폐 XLPE의 조성, 폐 XLPE의 입자크기 및 종류, 스크류 조합, 매트릭스 수지의 종류(LDPE, HDPE, PP, PS) 조건을 변화시키면서 배합물을 제조하고 그들의 기계적 및 유변학적 특성과 파단면을 조사하였다. 일반적으로 내외 전도층을 포함한 폐 XLPE 배합물의 충격강도는 내외 전도층을 제외한 배합물보다 충격강도가 작은 것으로 나타났다. 또한, XLPE의 함량이 증가하고 입자크기가 작아 질수록 배합물의 충격강도가 증가하였다. 특히, LDPF의 경우 XLPE를 약 80 wt%까지 충전하여도 정상조건의 압출공정이 가능하였다. 스크류조합에 따른 배합물의 충격강도는 니딩디스크 블록(kneading disc block)의 수가 많을수록 높은 값을 나타내었다. 전체적으로 XLPE의 양이 증가할수록 배합물의 용융점도가 증가하였으나, 압출 전단속도 범위에서 shear thinning 경향을 나타내었다. 폐 XLPE를 범용 고분자수지와 혼합할 경우, LDPE, HDPE, PP 및 PS 모든 배합물에서 충격강도가 증가하였다. 특히, PS/XLPE 배합물의 경우에는 충격강도가 2 배정도 향상되는 효과를 보여주었다.

• 한국식품과학회지
• /
• 제28권1호
• /
• pp.169-178
• /
• 1996

밀기울의 압출가공시 스크류의 조합과 공정변수 조절에 따른 압출물의 특성을 나타내는 target parameters(수분용해지수, 압출물의 고유점도, 보수력과 보유력, 식이섬유, 압출물의 미세구조)의 변화를 연구하였다. 수분용해지수(WSI)는 원료의 수분함량에 가장 큰 영향을 받았고, 역방향 스크류(RSE)를 5개 사용한 경우 밀기울이 13.7%인 것에 비하여 압출물은 $16.3{\sim}23.2%$의 범위로 높은 WSI를 보였다. 밀기울 압출물의 고유점도는 RSE가 $3{\sim}5$개로 증가할수록 높아져 원료 밀기울이 10.6 ml/g인 것에 비하여 $37.86{\sim}45.44\;ml/g$의 수준으로 증가하였으며, 원료의 수분함량과 압출압력에도 큰 영향을 받았다. 고유점도(IV) X 수용성 고형분(SS)의 무차원 변수와 기계적 에너지 소모율(SME)과의 관계는 높은 상관관계$(R^2=0.85)$를 보여 밀기울 세포벽 수용화 반응에 SS와 분자량 크기의 상관관계가 SME에 의하여 지배받는 인자임이 확인되었다. 압출물의 보수력은 원료의 공급량과 수분함량이 높을수록 원료 밀기울보다 높은 값을 보였고, 보유력은 원료 밀기울에 비하여 낮았다. 압출물의 수용성 식이섬유는 원료의 수분함량이 적은 조건에서 $4.32{\sim}6.48%$의 분포를 보여 원료 밀기울 2.68%보다 크게 증가하였다. 이는 압출공정이 밀기울 세포벽의 수용화에 효과적으로 작용하였음을 의미한다. 압출물의 미세구조는 원료의 수분함량에 따라서 붕괴와 용융정도의 차이를 보여 주었다.

• Journal of the Korean Wood Science and Technology
• /
• 제50권1호
• /
• pp.1-11
• /
• 2022

To evaluate the bearing strength of red pine cross-laminated timber (CLT) with self-tapping screw (STS), which is widely used as a fastener for connection in CLT building, the bearing test was conducted. Accoring to the STS's diameters (8, 10, 12 mm), the bearing test specimens with half hole were manufactured. Bearing strength was compared and reviewed in consideration of the configuration in STS and the loading direction to the grain of red pine. As a result of the bearing test on the STS's diameter, the yield bearing load increases as the larger diameter of the STS in all directions of the red pine. The bearing strength of the thread part (thread + tip) was higher than the shank part (shank + shank cutter). In compared with the directions to the grain of red pine, the bearing strength of the cross section parallel to the loading direction was the highest, and the tangent section was the lowest bearing strength. The average bearing strength of the loading direction in parallel to the grain was 23.43 MPa, which was about 45% higher than the average 16.16 MPa in perpendicular to the grain. The predicted bearing strength calculated by Eurocode (EN) and Korean Building Code (KBC)'s equation was lower than the experimental value. It is nessesary to propose the new equations of bearing strength reflected the configuration information of STS.

• 한국식품과학회지
• /
• 제23권1호
• /
• pp.88-92
• /
• 1991

스크류조합을 달리한 실험실용 twin-screw extruder를 사용하여 corn grit를 원료 투입량($30{\sim}60\;kg/hr$), 스크류 회전속도($200{\sim}400\;rpm$) 및 die hole 수($2{\sim}6$개) 범위에서 압출하면서 측정된 system parameters(압출온도, 기계적 에너지 소모율, 평균 체류시간)가 압출물의 특성을 나타내는 target parameters(수분 증발량, 수분 용해도지수 및 수분 흡착지수)에 미치는 영향을 스크류 조합별과 전체 실험결과를 다중회귀분석을 통하여 회귀식으로 나타내면, 스크류조합별 관계식에서는 상관계수가 0.90 이상 이었으며, 구획하지 않은 전체 회귀식에서는 0.80 정도의 상관계수를 보였다. 이상의 결과는 system analysis approach을 이용하면, 상이한 extruder사이의 조업자료 중 system parameters의 분석을 통하여 목적 제품의 특성을 예측할 수 있는 가능성을 보여준다고 생각된다.

• 한국수소및신에너지학회논문집
• /
• 제33권1호
• /
• pp.95-104
• /
• 2022

Micro hydropower is a readily available renewable energy source that can be harvested utilizing hydrokinetic turbines from shallow water canals, irrigation and industrial channel flows, and run-off river stream flows. These sources generally have low head (<1 m) and low velocity which makes it difficult to harvest energy using conventional turbines. A horizontal-axis screw turbine was designed and numerically tested to extract power from such low-head water sources. The 3-bladed screw-type turbine is placed horizontally perpendicular to the incoming flow, partially submerged in a narrow water channel at no-head condition. The turbine hydraulic performances were studied using Computational Fluid Dynamics models. Turbine design parameters such as the shroud diameter, the hub-to-shroud ratios, and the submerged depths were obtained through a steady-state parametric study. The resulting turbine configuration was then tested by solving the unsteady multiphase free-surface equations mimicking an actual open channel flow scenario. The turbine performance in the shallow channel were studied for various Tip Speed Ratios (TSR). The highest power coefficient was obtained at a TSR of 0.3. The turbine was then scaled-up to test its performance on a real site condition at a head of 0.3 m. The highest power coefficient obtained was 0.18. Several losses were observed in the 3-bladed turbine design and to minimize losses, the number of blades were increased to five. The power coefficient improved by 236% for a 5-bladed screw turbine. The fluid losses were minimized by increasing the blade surface area submerged in water. The turbine performance was increased by 74.4% after dipping the turbine to a bottom wall clearance of 30 cm from 60 cm. The final output of the novel horizontal-axis screw turbine showed a 2.83 kW power output at a power coefficient of 0.63. The turbine is expected to produce 18,744 kWh/year of electricity. The design feasibility test of the turbine showed promising results to harvest energy from small hydropower sources.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2011년도 정기총회 및 추계학술대회 논문집
• /
• pp.261-267
• /
• 2011

The test fit has commonly used for the evaluation of the railbed condition, and indirect methods by using the compressional wave are also studied. the direct evaluation method by penetration test has not been studied. For the measurement of in-situ cone tip resistance of the railbed with minimizing the disturbance of the upper railbed. the cone penetrometer with the helical type outer rod(CPH) was developed. The outer rod, which has helical screw, is penetrated through the gravel layer and provides the reaction force for cone penetration testing. the cone tip resistances are measured by the mini cone penetrometer, where diameter is 15mm. For the developing the mini cone, strain gauge installation, circuit configuration, penetration rates and calibration process are considered. For the easy penetration of the screw rod in the field, the reaction force stepping plate and guide column are arranged. The screw rod are penetrated through the gravel layer. And the mini cone was pushed into the subgrade railbed at the penetration rate of 1mm/sec. The penetration test shows that the cone tip resistance increases along the depth. In addition, the subgrade condition is evaluated. This study demonstrates that the CPH may be effectively used for the evaluation of subgrade method any damage of the gravel layer.

• 대한치과보철학회지
• /
• 제44권2호
• /
• pp.217-228
• /
• 2006

Statement of problem: Standard type of ITI solid implant model in the 6.2mm thick jaw bone was axisymmetrically modelled for finite element stress analyses. Purpose: Primary objective was to investigate the influences or the characteristic design configuration of the ITI solid implant model on the bone stress with the course of osseointegration process at the bone/implant interfaces. To simulate the characteristics of the osseointegration process, five different stages of the bone/implant interface model were implemented. As load conditions, vertical load of 50N was taken into consideration. Bone at the cervical region of implant was the areas of concern where the higher level of stress were likely to take place. Results: The results indicated that rather slightly different stress level could be obtained as a function of the osseointegration conditions. Conclusion: Under vertical load, the lower level of stress was observed at the cervical cortical bone in the initial and final stages of osseointegration. Relatively higher stress level, however, was observed during the transitional stages where the osseointegration at the cancellous bone interface were yet to fully develop.