• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.23 no.2
• /
• pp.76-80
• /
• 2013

For further improvement of osseo-integration of bone crystal with a dental implant, a design optimization study is carried out for various holes inside its body to deliver bioactive materials and the effect of bioactive material injection on the bone crystal growing. When bioactive material is absorbed, the bone crystal can grow into holes, which would increase the strength of implant bonding as well as a surface integration. The stress concentrations near the uppermost outlet holes were reduced with increasing the number of outlet holes. A design improvement in the uppermost outlet was shown to be effective in reducing the stress concentration. For design parameters under consideration in this study, total area of outlet of 6.38 $mm^2$ and maximum stress of 1.114 MPa, which corresponds to type 6-C. It is due to the minimization of maximum stress and total area of outlet. The design of the outlet facing down was more effective in reducing the maximum stress value compared with a horizontal symmetry.

• Bulletin of the Korean Chemical Society
• /
• v.32 no.3
• /
• pp.939-942
• /
• 2011

Conductive carbon films were prepared at room temperature by unbalanced magnetron sputtering (UBMS) on silicon substrates using argon (Ar) gas, and the effects of post-annealing temperature on the structural, tribological, and electrical properties of carbon films were investigated. Films were annealed at temperatures ranging from $400^{\circ}C$ to $700^{\circ}C$ in increments of $100^{\circ}C$ using a rapid thermal annealing method by vacuum furnace in vacuum ambient. The increase of annealing temperature contributed to the increase of the ordering and formation of aromatic rings in the carbon film. Consequently, with increasing annealing temperature the tribological properties of sputtered carbon films are deteriorated while the resistivity of carbon films significantly decreased from $4.5{\times}10^{-3}$ to $1.0{\times}10^{-6}\;{\Omega}-cm$ and carrier concentration as well as mobility increased, respectively. This behavior can be explained by the increase of sp2 bonding fraction and ordering $sp^2$ clusters in the carbon networks caused by increasing annealing temperature.

• Advanced Composite Materials
• /
• v.16 no.2
• /
• pp.181-194
• /
• 2007

This paper presents the mechanical properties of a composite consisting of acrylonitrile-butadiene-styrene (ABS) resin mixed with carbon fiber reinforced plastics (CFRP) pieces (CFRP/ABS). CFRP pieces made by crushing CFRP wastes were utilized in this material. Nine kinds of CFRP/ABS compounds with different weight fraction and size of CFRP pieces were prepared. Firstly, tensile and flexural tests were performed for the specimens with various CFRP content. Next, fracture surfaces of the specimens were microscopically observed to investigate fracture behavior and fiber/resin interface. Finally, the tensile modulus and strength were discussed based on the macromechanical model. It is found that the elastic modulus increases linearly with increasing CFRP content while the strength changes nonlinearly. Microscopic observation revealed that most carbon fibers are separated individually and dispersed homogeneously in ABS resin. Epoxy resin particles originally from CFRP are dispersed in ABS resin and seem to be in good contact with surrounding resin. The modulus and strength can be expressed using a macromechanical model taking account of fiber orientation, length and interfacial bonding in short fiber composites.

• Journal of Families and Better Life
• /
• v.31 no.4
• /
• pp.113-129
• /
• 2013

The purpose of this study was to develop and validate the Korea Family Strengths Scale II (KFSS-II) which was modified and developed by Yoo(2004). For this purpose, the preliminary scale of family strengths which was based on Yoo(2004)'s sample survey that targeted 494 adults who live in Korea consisted of 30 items. Exploratory factor analysis of 29 items extracted 5 factors. It included the 5 dimensional constructs of family resilience, valuing each other & acceptance, qualitative bonding, economic stability and cooperation and caring about community. Confirmatory factor analysis confirmed the stepwise 5-factor model of 22 items considering family strengths. These results indicated that the simple template of Family Strengths Scale would be a concise and reliable tool for assessing and evaluating a family's strengths.

• Journal of Contemporary Eastern Asia
• /
• v.16 no.2
• /
• pp.93-109
• /
• 2017

Cross-culturally, acts of sharing are recognized as an effective method to initiate and maintain human relationships in real-life situations by promoting continuous reciprocal exchanges between donors and recipients. Specifically, this study examines the effects of sharing a media product from the perspective of the givers, as compared to effects on the receivers. "Gangnam Style," a Korean music video, is of interest because it was spontaneously shared worldwide by young adults who used it as a vehicle to build and strengthen social relationships, among young adults. While both the givers and receivers of the "Gangnam Style" benefited from bridging new relationships, the results of this study found that those who gave "Gangnam Style" benefited more in terms bonding already existing relationships, compared to those who received materials. This study provides further evidence in support of the "sender-effect" paradigm and enhances our understanding of how online sharing contributes to the construction of social capital among the young adults.

• KIEE International Transactions on Power Engineering
• /
• v.4A no.4
• /
• pp.236-242
• /
• 2004

Previous research results indicated that the designed current reduction device could effectively reduce the sheath circulating current and that its RDP protection device could shield it against both fault and lightning strokes. In this paper, cable impedance is analyzed using wavelet analysis and distance relay algorithm following the installation of these devices so that the operation of distance relay can be estimated. The test results confirm that in these devices, the fault inception angle and SVL bonding types have no impact on the change of cable impedance. In other words, the conventional distance relay can be used without a new relay setting. Thus we can finally assert that the designed current reduction device and its protection device are effective and can be safely installed on the cable transmission system without disturbance.

• Journal of the Korea Institute of Building Construction
• /
• v.14 no.2
• /
• pp.163-169
• /
• 2014

Engineers in the construction field have been using bonded waterproofing sheets in an attempt to resolve the imbalance in the quality, the risk of fire, safety of workers, and environmental pollution, as well as to eliminate separate use of organic adhesives on the surface of concrete. Recently, self-laminated waterproofing sheets have been developed. The purpose of this research is to find an appropriate processing speed according to the changes in physical properties, and visual observation of the waterproofing sheets laminated by the aluminum thin-film and viscosity layer that can be attached through self-adhesiveness on the surface of concrete and waterproofing sheets. Therefore, this research is conducted using a physical performance test. Based on the result of the test, when the high-frequency inductive heating apparatus was used, an improved adhesion and bonding stability effect were confirmed after the anti-hydrostatic pressure and bond strength in the temperature condition, and the surface observation in the processing speed condition.

• Macromolecular Research
• /
• v.17 no.8
• /
• pp.568-574
• /
• 2009

We investigated the sintering and consolidation phenomena of silver nanoparticles under various thermal treatment conditions when they were patterned by a contact printing technique on polyimide substrate films. The sintering of metastable silver nanoparticles commenced at 180 $^{\circ}C$, where the point necks were formed at the contact points of the nanoparticles to reduce the overall surface area and the overall surface energy. As the temperature was increased up to 250 $^{\circ}C$, silver atoms diffused from the grain boundaries at the intersections and continued to deposit on the interior surface of the pores, thereby filling up the remaining space. When the consolidation temperature exceeded 270 $^{\circ}C$, the capillary force between the spherical silver particles and polyimide flat surface induced the permanent deformation of the polyimide films, leaving crater-shaped indentation marks. The bonding force between the patterned silver metal and polyimide substrate was greatly increased by the heat treatment temperature and the mechanical interlocking by the metal particle indentation.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.20 no.10
• /
• pp.112-118
• /
• 2021

In this study, an inspection method using a color image is proposed to conduct a real-time inspection of covalent organic framework (COF) films to detect defects, if any. The COF film consists of an upper pattern SR and a lower PI. The proposed system detects the defects of more than 20 ㎛ on the SR surface owing to the characteristics of the pattern, whereas on the PI surface, it detects defects of more than 4 ㎛ by utilizing a micro-optical system. In the existing system, it is difficult for the operator to conduct a full inspection through a high-performance microscope. The proposed inspection algorithm performs the inspection by separating each color component using the color contrast of the pattern on the SR side, and on the PI surface it inspects the bonding state of the mounted chip. As a result, it is possible to confirm the exact location of the defects through the SR and PI surface inspections in the implemented inspection.

• Steel and Composite Structures
• /
• v.31 no.3
• /
• pp.217-232
• /
• 2019

Modular steel buildings consist of prefabricated room-sized structural units that are manufactured offsite and installed onsite. The inter-module connections must fulfill the assembly construction requirements and soundly transfer the external loads. This work proposes an innovative assembled connection suitable for modular buildings with concrete-filled steel tube columns. The connection uses pretensioned strands and plugin bars to vertically connect the adjacent modular columns. The moment-transferring performance of this inter-module connection was studied through monotonic and cyclic loading tests. The results showed that because of the assembly construction, the connected sections were separated under lateral bending, and the prestressed inter-module connection performed as a weak semirigid connection. The moment strength at the early loading stage originated primarily from the contact bonding mechanism with the infilled concrete, and the postyield strength depended mainly on the tensioned strands. The connection displayed a self-centering-like behavior that the induced deformation was reversed during unloading. The energy dissipation originated primarily from frictional slipping of the plugin bars and steel strands. The moment transferring ability was closely related to the section dimension and the arrangements of the plugin bars and steel strands. A simplified strength calculation and evaluation method was also proposed, and the effectiveness was validated with the test data.