• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.17 no.6
• /
• pp.83-90
• /
• 2018

This paper introduces a innovative diamond wire saw cutting technology and its experimental verification that can be utilized for cutting heavy structures. While conventional diamond wire saw cutting technologies such as water cooled cutting method and dry cutting method cause severe environmental problems due to generating massive concrete sludge or dust scattering, the proposed method can eliminate those problems considerably. Through extensive experiments using heavy structure test bed and real bridge pier structure, comprehensive analysis and comparative evaluation about various cutting methods were performed. As a result, the innovative diamond wire saw cutting method could achieve a similar cutting and cooling performance to the water cooled cutting method without generating concrete sludge and it showed an improved cutting and cooling performance to the dry cutting method without dust scattering. Consequently it is confirmed that the suggested cutting technology can be a promising environment-friendly alternative in the field of heavy structure dismantling.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2000.05a
• /
• pp.934-938
• /
• 2000

Built-up edge affects the surface integrity of the machined surface and tool wear. Tool geometry and cutting conditions are very important factors to remove BUE. In this paper, we optimized the geometry of the metal slitting saw .1nd cutting conditions to remove BUE by the experiment. In general, the metal slitting saw is plain milling cutter with thickness less of a 3/16 inch. This is used for cutting workpiece where high dimensional accuracy and surface finish are necessary. The experiment was planned with Taguchi method that is based on the orthogonal array of design factors(coating, rake angle, number of tooth, cutting speed, feed rate). Response table was made by the value of the surface roughness, the optimized tool geometry and cutting conditions through response table could be determined. In addition. the relative effect of factors were identified by the variance analysis. filially. coating and cutting speed turned out important factors.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.39 no.10
• /
• pp.1069-1077
• /
• 2015

In tunnel excavation using blast, the wire saw rock cutting method generates a discontinuity perimeter around the center cut, and thus prevents blast vibration propagation to reduce vibration and noise. Therefore, the method is expected to be easy to use and economical compared with other methods. In this paper, the cutting mechanism of wire saw in tunnel excavation is investigated. A model describing the changes in cutting depth and wire saw shape inside a rock during cutting is established and validated for this purpose. Through a simulation using the model, the important characteristics of wire saw cut are investigated, and the influences of cutting conditions, such as wire saw tension, wire saw speed, feed speed, depth, and diameter of boring, on cutting performance are also examined. A method to improve the cutting performance is proposed based on the results.

• Journal of KSNVE
• /
• v.9 no.6
• /
• pp.1210-1217
• /
• 1999

This paper presents schematic process of identifying the principal cause to make the vibration problem of rotating circular saws. In the tandem pencil slat saw lines, feeding of cedar blocks is often stopped because excessive motro current is required in a saw motor. These events are called "kick-offs" in technical reports. Research on saw behavior at kick-offs is required to understand are reduce the frequency and severity of kick-offs events. This research aims at finding out the principal cause of kick-offs, and evloving design improvements for high cutting performance with fewer and less severe kick-offs. Measurements of critical speed, cutting force, cutting temeprature and dynamic displacements are carried out to observe the instability mechanism and also to obtain saw design parameters for the numerical analyses. And the numerical analyses involving FEM and multiple scale method are utilized to show the possibility of the principal cause.pal cause.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.17 no.6
• /
• pp.615-621
• /
• 2015

In this paper diamond wire cutting method has been proposed to cut the rock in the tunnel face. Diamond wire saw method could cut the rock from tunnel face with very minor vibration and noise. In this study rock cutting process has been simulated with FEM method by using LS-DYNA explicit non-linear finite element code. Normal load act as an prime factor when cutting the rock surface. For observing the effect of normal load on bead, several experiments has been conducted by varying normal loads on the bead. From each experiment, cutting rate has been calculated to compare the cutting rate with different load conditions. By increasing the normal load on bead, cutting rate increases drastically.

• Proceedings of the KSME Conference
• /
• 2008.11a
• /
• pp.955-960
• /
• 2008

In this paper, an impulse of an industrial chop Saw is identified by experimental method and the impulse is reduced by structural modification. For the impulse identification, vibration signals are measured by an accelerometer when the chop saw is operating. From some experiments, it is found that the impulse occurs when there is slip between spindle and the wheelwasher and contact area is small between the wheelwasher and cutting discs. The design of the wheelwasher for optimization is performed by the FEM and experiments and the prototype is manufactured. It is verified that considerable amount of impulses are reduced by the structural modification.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.23 no.4
• /
• pp.328-333
• /
• 2003

It has been widely recognized that the residual stress of the weldment affect the integrity of steel structures and cause an initiation of crack in the welded regions. Since the power plants adopt a variety of welding processes, it is necessary to know the distribution and magnitude of residual stresses. This paper has attempted to investigate the validity of the saw cutting method and the indentation method to measure the residual stresses in the steel plates. The residual stresses in the specimens of hot reheater pipes, cold reheater pipes and feed water lines in power plants were determined by the saw cutting method and the indentation method. The data were compared and reviewed for the validity of the methods.

• Journal of the Korean Society for Precision Engineering
• /
• v.18 no.5
• /
• pp.130-136
• /
• 2001

Generally, a metal slitting saw is plain milling cutter with thickness less than 3/16 inch. This is used for cutting a workpiece that high dimensional accuracy and surface finish is necessary. A small thin milling cutter like a metal slitting saw is useful for machining a narrow groove. In this case, built up edge(BUE) is severe at each tooth and affects the surface integrity of the machined surface and tool wear. It is well known that tool geometry and cutting conditions are decisive factors to remove BUE. In this paper, we optimized the geometry of the milling cutter and selected cutting conditions to remove BUE by the experimental investigation. The experiment was planned with Taguchi method based on the orthogonal array of design factors such as coating, rake angle, number of tooth, cutting speed, feed rate. Response table was obtained from the number of built-up edge generated at tooth. The optimized tool geometry and cutting conditions could be determined through response table. In addition, the relative effect of factors was identified bh the analysis of variance (ANOVA). Finally, coating and cutting speed turned out important factors for BUE.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.19 no.9
• /
• pp.892-898
• /
• 2009

In this paper, a cause of a shock of an industrial chop saw is identified by experimental method and the shock is reduced by structural modifications. For the shock identification, vibration signals are measured by an accelerometer when the chop saw operates. Through some experiments, it is found that the shock is occurred by a slip between a spindle and a wheelwasher of the chop saw. To reduce the shock, One method is to lower the mass moment of inertia of the wheelwasher and the angular rotating acceleration of it. Another method is to broaden a contact area between the wheelwasher and the spindle. After designing and analyzing the wheelwasher and the spindle mechanically, a prototype of them is built. With the manufactured prototype, the performances and design requirements of them are experimentally verified by the response measurements.

• Journal of Power System Engineering
• /
• v.8 no.2
• /
• pp.12-17
• /
• 2004

In this study, to verify the reliability of the indentation for measuring welding residual stresses to get in method we compared the results of the method with those measured by the saw cutting method. Also for the same purpose we used a 4-point bending test and confirmed the reliability of indentation method. The specimens used in this experiment are made with the same conditions for hot reheater pipes and cold reheater pipes used in the electric power plant. Therefore we could know that the results of the methods showed the reliability of the method to obtain welding residual stresses.