• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.11 no.5
• /
• pp.481-486
• /
• 2018

DC motors are classified as DC motors with brush structure and BLDC motors without brush structure. Representing the speed control of the BLDC motor is the PI control. The speed control using the PI controller has a disadvantage that the response characteristic to reach the steady state is slow. Therefore in this paper, a voltage controlled speed controller using a Fuzzy Logic Controller (FLC), which has a short steady response time and usefulness of nonlinear control. The validity and usefulness of the proposed fuzzy speed controller are verified by simulation through Simulink of MATLAB program. Experiments were performed on the PI controller and the proposed fuzzy speed controller in three cases with reference speeds of 500rpm, 800rpm, and 1500rpm. Experimental results show that the proposed fuzzy controller has more 30% improved steady state speed response than PI controller.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.11 no.5
• /
• pp.579-585
• /
• 2018

This study is to figure out the fuel injection characteristics according to the injection pressure and engine speed in the fuel supply system for gas fuel. The fuel rail pressure was from 1.5 to 6.0 bar by 1.5 bar increment and engine speed was set 1,000 ~ 6,000 RPM at interval of 1000 RPM. Considering the real engine operation, the injection pulse width was set 2.5ms, 5.0ms, and 13.0ms which correspond low, mid and high load condition respectively. In conclusion, in case of 100cc fuel rail, 4.5 bar of injection pressure showed best performance and the minimum required injection quantity 53cc which guarantees engine output can be obtained in each 1000~ 6000 rpm engine speed.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.16 no.5
• /
• pp.3044-3050
• /
• 2015

The purpose of this study is to analyze the performance of the flow control oil pump for automatic transmission. The numerical model for analysis the performance of the flow control oil pump was develop and the characteristics of the internal flow, discharge flow rate, displacement of outer ring, driving torque, generation of cavitation was investigated according to rotating speed. As a result, the cavitation generation increased as the rotating speed increased. The volumetric efficiency was 90% for 2200 rpm and it decreased rapidly, then it decreased about 81% for 5000 rpm. Besides, the cavitation generation was 20%~30% for inlet of suction part, but it reduced below 13% owing to the compression. However, it shows higher cavitation generation for high rotating speed like 5000 rpm.

• Korean Journal of Food Science and Technology
• /
• v.16 no.3
• /
• pp.329-335
• /
• 1984

The effect of peeling methods, spherecity and weight of potatoes and carrots on the peeling efficiency were investigated. The changes in the surface texture by peeling were estimated by Rheometer and were related to the changes in the microstructure. The optimum mechanical peeling conditions using abrasion type rotary peeler were 90 sec. at 300 rpm for potatoes, 70 sec. at 300 rpm for sweet potatoes and 60 sec. at 300 rpm for carrots. The peeling loss was influenced by the sphericity and weight of the sample. The optimum conditions for alkali peeling were 90 sec. immersion in boiling 10% NaOH solution for potatoes, 300 sec. in boiling 10% NaOH solution for sweet potatoes and 60 sec. in boiling 6% NaOH solution for carrots. Severe damage of surface structure was noticed by alkali peeling, demonstrated by denaturation of starch granules in the cell. The structural damage observed by microscope was related to the reduction of cutting force after peeling.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2008.11a
• /
• pp.94-97
• /
• 2008

As the partial admission turbine has a intrinsically unsteady and three dimensional flow region, numerical calculation time of these study has been too long time. The numerical analysis for gas temperature of turbine blade surface has been performed to investigate development of temperature with various pyro start pressure. Computations have been carried out several turbine rotational speeds in the range from 0 to 16000 rpm and inlet conditions with 1423K, 7.2MPa. As a result, the more rotational speed and pyro starter pressure of turbine increased, the more turbine blade's temperature decreased. It is also found that flow field of turbine blade inlet area at pyro starter pressure of 5.75MPa and rotational speed of 12100 rpm formed surface temperature uniformly.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.39 no.1
• /
• pp.115-122
• /
• 2019

Steel Fiber Reinforced Wet-type Shotcrete improves the quality and stabilizes the tunnel by increasing the shear strength of the natural ground by constructing the concrete which attaches the fresh concrete to the predetermined position from the nozzle. The Steel Fiber Reinforced Wet-type Shotcrete improves and reinforces the strength and dynamic behavior characteristics of concrete to suppress the generation and growth of local cracks by increasing the tensile resistance ability. In addition, Steel Fiber Reinforced Wet-type Shotcrete is a shotcrete that improves tensile strength, bending strength, and crack resistance by dispersing discontinuous short steel fibers evenly in concrete. In this study, compressive strength test and bending strength test of shotcrete of NATM tunnel were measured and rebound reduction rate was measured by varying shotcrete putting pressure to 900 RPM, 1,000 RPM, and 1,100 RPM. Therefore, the data that can be applied to domestic NATM tunnel construction are presented.

• Journal of Convergence for Information Technology
• /
• v.8 no.6
• /
• pp.187-192
• /
• 2018

This thesis is about the study of inverter terminal boxes in a explosion proof type exhaust fan that can control wind volume and operating time. In Korea, there is no ventilator to adjust the amount of wind and operating time when working in poor conditions. The purpose of the project is to create a explosion terminal box that can control the operating time and wind speed of a suitable explosion ventilator in hazardous environments. The two explosion-proof switches allow the operation time to be driven 1 hour, 3 hours and continuous time, and the speed of the induction motor rotation was set in 3 stages at 2000 rpm, 2600 rpm and 3000 rpm to control the volume. The tested motor used a half-horsepower barrier three-phase induction motor and a full-bridge inverter to set the desired flow rate and operating time.

• Journal of Advanced Navigation Technology
• /
• v.23 no.3
• /
• pp.245-250
• /
• 2019

Inertial navigation system has navigation errors because of the error of inertial measurement unit (IMU) and misalignment over time. In order to solve this problem, aided navigation system is performed using global navigation satellite system (GNSS), speedometer, etc. The inertial navigation system equipped with underwater vehicle mainly uses speedometer and performed aided navigation because satellite signals do not pass through underwater. There are DVL, EM-Log, and RPM in the speedometer, and the sensors are applied according to the system environment. This paper describes velocity aided navigation using RPM of inertial navigation system operating in high speed and deep water environment. In addition, we proposes an algorithm to compensate the limit of RPM with straight direction and the current velocity error. There are results of monte-calo simulation to prove performance of the proposed algorithm.

• Korean Journal of Agricultural Science
• /
• v.48 no.3
• /
• pp.535-544
• /
• 2021

When baking, the proper blending or mixing of materials will affect the quality of the product. The mixing strength is important when establishing the optimal conditions for batter, and control of the mixing condition is accordingly an important factor. This study investigated the effects of the mixing speed and time on the quality characteristics of a gluten-free type of rice batter. The batter samples manufactured for this purpose are as follows: control (+) (wheat flour), control (-) (rice flour), T1 (1,800 rpm, 1 min), T2 (1,800 rpm, 2 min), T3 (1,800 rpm, 3 min), T4 (3,600 rpm, 1 min), T5 (3,600 rpm, 2 min), T6 (3,600 rpm, 3 min). In this study, rice flour was used in the T1 to T6 samples. The pH of the batter tended to be higher when the mixing speed was slower and the time was shorter depending on the ultra-high mixing conditions. The moisture content of T3 was highest, and there was no difference according to the ultra-high speed conditions. The specific volumes of the ultra-high mixing treatments were higher than those of the control samples. The relationship between the specific volume, hardness and springiness of rice bread according to the mixing speed and time was weak. Therefore, it is considered that the application of ultra-high speeds when manufacturing gluten-free batter can have a positive effect on improving the production efficiency by reducing the processing time.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.59 no.1
• /
• pp.28-34
• /
• 2023

In the anchovy boat seine fishing boat, it is necessary to select other aquatic organisms other than live anchovies, which are the target species of catch. By making a rotating roller sorter using hydraulic pressure, the anchovy sorting amount was compared and the sorting accuracy of the rotary roller sorter, and the discharge speed of butter fish and jerry fish according to the number of roller revolutions were analyzed. The rotating roller sorter increases the weight of the sorted raw anchovy by 54%, 74% and 91.5% compared to the round bar fixed type, so it can reduce the required time by an average of 73.2%. As a result of converting the sorting accuracy to the weight of pure anchovies excluding the catch weight, the round bar fixed type was 89%; however, the average of the rotating roller sorter was 97.7%. Thus, the sorting accuracy of the rotary roller sorter was further improved by about 8.7%. The roller speed moved 7% at 300 rpm, 7.5% at 600 rpm, and 16% at 900 rpm, so butter fish were discharged overboard 10% faster than jelly fish on average. In addition, the average feed speed of butter fish and jelly fish is 1,400 mm/s when the roller rotation speed is 300 rpm, 1,480 mm/s at 600 rpm, and 1,850 mm/s at 900 rpm. A Φ58 mm roller rotates once it moved about 1.23 mm. In the future, a follow-up study of quantitative evaluation is needed targeting more non-target fish species of anchovy boat seine.