• Resources Recycling
• /
• v.18 no.6
• /
• pp.54-59
• /
• 2009

The level manufacturing technique for refuse derived fuel (RDF) is possible to produce them itself by a domestic process which is appropriate in Korea. However, very few facilities were used for industrial combustible waste. The objective of this research is to develop the technique for refuse plastic fuel (RPF) of industrial waste. RPFs were prepared by mixing of plastic, paper and wood based on amount of regional waste. The physical properties of the RPFs prepared were investigated. RPFs prepared at mixing ratio(plastic : paper : wood) of 87.55% : 8.15% : 4.3% show the highest lower heating values in wet-base (LHVW) and the LHVW decreases as the mixing ratio of paper and wood increases.

• Journal of Soil and Groundwater Environment
• /
• v.27 no.spc
• /
• pp.75-91
• /
• 2022

Differences in subsurface migration of LNAPL/DNAPL contaminants caused by a selection of 3-phase (aqueous, NAPL, and gas) relative permeability function (RPF) models in numerical modeling were investigated. Several types of RPF models developed from both experimental and theoretical backgrounds were introduced prior to conducting numerical modeling. Among the RPF models, two representative models (Stone I and Parker model) were employed to simulate subsurface LNAPLs/DNAPLs migration through numerical calculation. For each model, the spatiotemporal distribution of individual phases and the mole fractions of 6 NAPL components (4 LNAPL and 2 DNAPL components) were calculated through a multi-phase and multi-component numerical simulator. The simulation results indicated that both spilled LNAPLs and DNAPLs in the unsaturated zone migrated faster and reached the groundwater table sooner for Stone I model than Parker model while LNAPLs migrated faster on the groundwater table under Parker model. This results signified the crucial effect of 3-phase relative permeability on the prediction of NAPL contamination and suggested that RPF models should be carefully selected based on adequate verification processes for proper implementation of numerical models.

• Journal of Food Hygiene and Safety
• /
• v.27 no.2
• /
• pp.169-175
• /
• 2012

Five kinds of selective media, such as mannitol salt agar (MSA), Baird-Parker agar (BPA), Baird-Parker supplemented with rabbit plasma fibrinogen (BPA+RPF), CHROMagar Staphylococcus aureus (CSA), and Petrifilm Staph Express count system (Petrifilm), were compared to recommend the optimum selective media for isolation of Staphylococcus aureus from agricultural products. Seventy four target and non target bacteria were inoculated on five selective media to analyze sensitivity and specificity. In the recovery test of injured S. aureus cells, S. aureus was exposed to acid (1% lactic acid for 10 min), heat ($60^{\circ}C$ for 90s), and cold ($-20^{\circ}C$ for 1h) conditions. And artificially contaminated agricultural products (iceberg lettuce, green pepper, and cherry tomato) was enumerated on five selective media. The sensitivity of BPA+RPF, CSA, Petrifilm, MSA, and BPA were 100%, 100%, 100%, 90.5%, 90.5%, respectively. In addition, the specificity of BPA+RPF, CSA, MSA, BPA and Petrifilm were 100%, 100%, 84.6%, 75.0%, 67.3%, respectively. However, no difference among five selective media was observed in recovery on injured S. aureus cell and enumeration from agricultural products. This results suggest that BPA+RPF and CSA are the optimum media for detection of S. aureus from agricultural products.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.19 no.7
• /
• pp.94-99
• /
• 2005

This paper presents a method to assess total transfer capability(TTC) considering transient stability. TTC is limited not only by the violation of system voltage and thermal limits, but also restricted by transient stability limit, TTC calculation is divided into two processes. The frist step is to calculate TTC without considering the transient stability constraint by using repeated power flow(RPF) method. The second step is to perform transient stability analysis based on TTC calculation in the frist step.

• Journal of the Korean Society of Combustion
• /
• v.15 no.3
• /
• pp.48-56
• /
• 2010

Performances of power generation engine were investigated with syngas from RPF. A stoker type, multi-staged pyrolysis-gasification system, was employed for syngas generation and the syngas was refined with the sequential cleaning processes composed of a gas cooler, a bag filter and a wet scrubber. 20 kWe commercial syngas power generation engine was adopted to burn the cleaned syngas which is mainly composed of hydrogen, carbon monoxide, carbon dioxide and methane. The performance of the engine was tested with various syngas compositions and the results were compared to LNG case. Electric power output, exhaust gas temperature, and emission characteristics were measured, and the efficiency of engine generation was investigated as a function of load of power generation.

• Journal of Korean Society of Steel Construction
• /
• v.9 no.4 s.33
• /
• pp.697-705
• /
• 1997

The conventional preflex beams are designed by the method of paritial prestressing and allow the tensile stresses at the lower concrete of beams. As a consequence, most of preflex beams experience the tensile cracks under the service loads. This study was conducted to develop the most effective preflex beams, which do not allow tensile stress under the service load, by introducing additional prestressing called 'represtressing' at the lower concrete of beams. The objective of the study was accomplished by developing a computer analysis and design program and conducting experiments. Using the developed computer program, standard sections of the represtressed preflex beams were determined by computer modeling. In the experiment, two actual size of represtressed beams were tested under the imitated service loads. The results of test have shown that the performance of the represtressed preflex beams is generally excellent. A remarkable improvement was made in the design of preflex composite beams. Since the represtressed preflex beams(RPF) do not experience the tensile cracks under the service loads, the use of this beam for the bridge structures will lead to easy bridge maintenance and management. Furthermore, due to the low beam depth, high clearance and economical design can be realized in the bridge design using RPF.

• Magazine of the Korea Concrete Institute
• /
• v.15 no.4
• /
• pp.55-59
• /
• 2003

• 재활용회보
• /
• s.1
• /
• pp.114-115
• /
• 2003

• 한국신재생에너지학회:학술대회논문집
• /
• 2010.06a
• /
• pp.207.1-207.1
• /
• 2010

The emission difference of SOx, NOx, TSP and dioxine was investigated in commercial CFB boiler, when coal and three kinds of RDFs were co-combusted respectively. The each mixing ratio was 7.5% RPF, 7.5% RDF and 10% SDF with coal. Emitting dioxine concentration was proportioned to the chlorine content of RDF. No trouble was found on normal boiler operation during co-combustion. These RPF, SDF and RDF could be determined to be a good alternative fuel of general coal.

• 한국신재생에너지학회:학술대회논문집
• /
• 2005.11a
• /
• pp.414-422
• /
• 2005

유럽에서 RDF기술 확산 동향과 국가별 RDF사용 현황, 각국의 RDF품질표준 및 최근 유럽공통RDF품질표준화 추진현황을 소개하고 RDF사용처별 경제성분석 내용을 소개하였다. 소각로, 시멘트공장 및 석탄화력발전소에서 RDF를 사용할 경우에 열회수량은 시멘트공장이 다소 높게 나타났고 손익평가(cost benefit balance)는 석탄화력발전소가 가장 높게 나타났다. 국내에서 가동 중인 20MW급 순환유동층 석탄화력발전보일러에서 폐플라스틱고형연료(RPF)를 혼합연소하는 기술과 염화수소 및 다이옥신 측정내용을 소개하였다. 전염소량 0.4$\sim$0.6% RPF를 2.5%혼소 시 염화수소는 10ppmv 정도로 분석되었고 다이옥신은 0.003ng-TEQ/$Sm^3$으로 거의 검출이 되지 않았다.