• Journal of the Korean Institute of Telematics and Electronics C
• /
• v.34C no.11
• /
• pp.47-55
• /
• 1997

In general, processing flow of the conventional floating-point multiplication consists of either multiplication, addition, normalization, and rounding stage of the conventional floating-point multiplier requries a high speed adder for increment, increasing the overall execution time and occuping a large amount of chip area. A floating-point multiplier performing addition and IEEE rounding in parallel is designed by using the carry select addder used in the addition stage and optimizing the operational flow based on the charcteristics of floating point multiplication operation. A hardware model for the floating point multiplier is proposed and its operational model is algebraically analyzed in this paper. The proposed floating point multiplier does not require and additional execution time nor any high spped adder for rounding operation. Thus, performance improvement and cost-effective design can be achieved by this suggested approach.

• Journal of Korean Society for Quality Management
• /
• v.16 no.1
• /
• pp.23-31
• /
• 1988

This paper studies the handling of significant digits and rounding off methods in domestic industries. ANOVA tables made by six well-known big companies are selected and analyzed. There exist various mistakes in handling of significant digits and rounding off methods such as: * too many significant digits in the Sum of Squares values in comparison to the original data * too many significant digits in the variance ratio in comparison to the F table values. * no consistancy in the number of significant digits * no consideration for the number of significant digits in computations * ignoring the KS A 0021 in rounding off methods etc. Such mistakes are caused from the characteristics of the personal computers rather than the misunderstandings about the significant digits conception. A subroutine is developed for PC in BASIC language to help the handling of significant digits and rounding off.

• The Journal of Korean Academic Society of Nursing Education
• /
• v.29 no.4
• /
• pp.381-394
• /
• 2023

Purpose: This study aimed to develop an intentional rounding protocol to enhance the clinical competence of nursing students. Methods: An intentional rounding protocol for nursing students' clinical practice was developed following the ADDIE (Analysis, Design, Development, Implementation, and Evaluation) model. A convenient sampling method was used to select 23 junior year university nursing students during their clinical practice in adult nursing. The program evaluation included a quantitative assessment (communication and relationship efficacy, empathy, and patient safety competency) and focus group interviews. Results: The intentional rounding protocol focused on the 4Ps (pain, position, potty, and possessions) and encompassed aspects such as level of consciousness, pain management, personal care needs, intravenous injection, oxygen administration, nasogastric/nasoenteric tube care, maintenance of urine collection bags, and the identification of environmental fall risks. Nursing students performed intentional rounding at least twice a day. Following the implementation of this protocol, nursing students demonstrated a significant improvement in communication and interpersonal efficacy. The focus group interviews revealed four main themes: growth of human relationships, acquiring knowledge in and about the clinical field, becoming a nurse, and barriers in reality. Conclusion: The intentional rounding protocol has the potential to enhance nursing students' communication and interpersonal skills during clinical practice and to provide them with positive experiences in nursing clinical education. Therefore, it is recommended that this protocol be incorporated into nursing clinical practice education.

• Current Applied Physics
• /
• v.18 no.11
• /
• pp.1268-1274
• /
• 2018

We have investigated the effects of chemical rounding (CR) on the surface passivation and/or antireflection performance of $AlO_{x^-}$ and $AlO_x/SiN_x:H$ stack-passivated pyramid textured $p^+$-emitters with two different boron doping concentrations, and on the performance of bifacial n-PERT Si solar cells with a front pyramid textured $p^+$-emitter. From experimental results, we found that chemical rounding markedly enhances the passivation performance of $AlO_x$ layers on pyramid textured $p^+$-emitters, and the level of performance enhancement strongly depends on boron doping concentration. Meanwhile, chemical rounding increases solar-weighted reflectance ($R_{SW}$) from ~2.5 to ~3.7% for the $AlO_x/SiN_x:H$ stack-passivated pyramid textured $p^+$-emitters after 200-sec chemical rounding. Consequently, compared to non-rounded bifacial n-PERT Si cells, the short circuit current density Jsc of 200-sec-rounded bifacial n-PERT Si cells with ~60 and ${\sim}100{\Omega}/sq$ $p^+$-emitters is reduced by 0.8 and $0.6mA/cm^2$, respectively under front $p^+$-emitter side illumination. However, the loss in the short circuit current density Jsc is fully offset by the increased fill factor FF by 0.8 and 1.5% for the 200-sec-rounded cells with ~60 and ${\im}100{\Omega}/sq$ $p^+$-emitters, respectively. In particular, the cell efficiency of the 200-sec-rounded cells with a ${\sim}100{\Omega}/sq$ $p^+$-emitter is enhanced as a result, compared to that of the non-rounded cells. Based on our results, it could be expected that the cell efficiency of bifacial n-PERT Si cells would be improved without additional complicated and costly processes if chemical rounding and boron doping processes can be properly optimized.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.8 no.3
• /
• pp.454-462
• /
• 1998

Mechanisms and conditions for rounding of AUC particles were examined during AUC precipitation. Rounding of AUC particle was possible only by external circulation using pump, not by internal circulation using agitator. The rate of AUC rounding $(dn_p/dt)$ was proporational to operation conditions such as magma density $(M_t:g-U/{\iota}l)$, turn over ratio $(T_o)$ and impeller tip velocity of pump (U); $ dn_p/dt{\propto}M_t{\cdot}T_o{\cdot}U^2$. The validity of this relationship was qualitatively confirmed by comparing the expermental results. Two rounding mechanisms were suggested. One is crack formation mechanism and the other etch-pit formation mechanism on the surface of AUC particle. It was found that the crack formation is more dominant at the initial stage and the etch-pit formation at the final stage of the AUC precipitation.

• KSTLE International Journal
• /
• v.2 no.2
• /
• pp.85-92
• /
• 2001

The variation of contact traction induced by different contact shapes is studied experimentally and theoretically. Considerations fer the contact shape are rounded, truncated and truncated with rounding punches. A fretting wear experiment is conducted with the contact configuration of the strip on the tube specimens. The strip specimen is pressed to form the end profile of a rounded and truncated with rounding punches shape. Wear on the tube is investigated, which is regarded as the slip region of the contact surface. Taken into consideration is the general solution of the normal traction in the case of the indentation by a punch with its end profile of the combination of parabolas. Then, partial slip solution is obtained numerically, which is compared with the wear on the tube. The radius of the rounding and the obliquity of the edge truncation affect the tractions considerably. It is found that the proper choice of the end profile can restrain the contact-induced failure such aswear.

• Proceedings of the KSME Conference
• /
• 2001.06c
• /
• pp.269-274
• /
• 2001

In order to reduce trial-and-errors in the die design and production, CAE systems for analysis of stamping tools have been introduced at the initial design stage recently. For optimal design, the CAE engineers may need to correct the meshes generated by automatic mesh generation programs. However, they may need help of CAD engineers as they are usually not skilled in manipulation of CAD systems. In order to get around these problems, automatic shell mesh modification method is proposed, which utilizes existing CAD/CAE package (in this study, I-DEAS) without user interaction. The developed method and optimization techniques are applied to a stamping die rounding optimization problem. The optimization results show that the manpower and the time required at virtual tryout can be reduced by using the developed systems.

• KSBB Journal
• /
• v.22 no.5
• /
• pp.282-287
• /
• 2007

The antiviral mechanism of KT5720 is known to inhibit the cAMP-dependent protein kinase (PKA), on the VSV infection in BHK-21 cell cultures. The virus inducted CPE (cell rounding) was almost completely suppressed by KT5720 at 5 uM. The inhibitor, however, did not affect the replication of the virus and the synthesis of viral macromolecules. Immunological studies showed the viral matrix (M) protein displayed intimate association with the cytoskeletal components and probably the cell rounding. KT5720, did not block the cytoskeletal disruption, while the cell rounding was suppressed. These observations suggest that the interaction between the viral M protein and the cytoskeletal components may not be enough to cause the morphological change of the cell. And, the KT5720-sensitive function may be involved in developing the VSV-induced CPE, but not essential for the virus replications.

• Korean Journal of Optics and Photonics
• /
• v.4 no.4
• /
• pp.403-410
• /
• 1993

The scalar diffraction theory of the read-out signal in optical disc is described. and numerical results is given. The strength of this signal depends on the shape of bump(pit) which show more or less rounding of the edge because of the photoresist process. It is shown that the ideal shape is the retangular form, with no rounding of edge. This form is not achievable in practise. but the results show that very satisfactory values of the read-out signal can nevertheless be achieved in the presence of the moderate amounts of rounding.unding.

• Proceedings of the IEEK Conference
• /
• 1998.10a
• /
• pp.1025-1028
• /
• 1998

Hardware to implement the parallelized Floating-point rounding algorithm is described. For parallelized additions, we propose an addition module which has carry selection logic to generate two results accoring to the input valuse. A multiplication module for parallelized multiplications is also proposed to generate Sum and Carry bits as intermediate results. Since these modules process data in IEEE standard Floatingpoint double precision format, they are designed for 53-bit significands including hidden bits. Multiplication module is designed with a Booth multiplier and an array multiplier.