• 소성∙가공
• /
• 제16권4호
• /
• pp.299-303
• /
• 2007

Dry sliding wear behavior of ultra-fine grained(UFG) plain low carbon dual phase steel, of which microstructure consists of hard martensite in a ductile ferrite matrix, has been investigated. The wear characteristics of the UFG dual phase steel was compared with that of a coarse grained dual phase steel under various applied load conditions. Dry sliding wear test were carried out using a pin-on-disk type tester at various loads of 1N to 100N under a constant sliding speed condition of 0.20m/s against an AISI 52100 bearing steel ball at room temperature. The sliding distance was fixed as 1000m for all wear tests. The wear rate was calculated by dividing the weight loss, measured to the accuracy of 10-5g by the specific gravity and sliding distance. The worn surfaces and wear debris were analyzed by SEM, EDS and profilometer. Micro-vickers hardness of the cross section of worn surfaces were conducted to analyze strain hardening underneath the contact surfaces. The wear mechanism of the UFG dual phase steel was investigated with emphasis on the unstable nature of the grain boundaries of the UFG microstructure.

• Journal of Welding and Joining
• /
• 제2권1호
• /
• pp.49-57
• /
• 1984

The influence of weld defect, residual stress and microstructure on the Low Cycle Fatigue(L. C. F.) behaviour of AISI 304L austenitic stainless steel weldment has been studied. The specimens were welded by shielded metal are welding process, post weld heat treated(PWHT) at 900.deg.C for 1.5hrs, and tested under total strain controlled condition at room temperature. The results of the experiment showed that weld defect affected the L.C.F. behaviour of weldment deleteriously compared to the residual stress or microstructure, and it reduced the L.C.F. life about 70-80%. The PWHT exhibited beneficial effect on the L.C.F. behaviour and increased the L.C.F. life about 120%. This enhancement by PWHT was attributed to the removal of residual stress and recovery of weld metal ductility. The cyclic stress flow of as welded specimens showed intermediate cyclic softening, whereas those of heat treated specimens showed continuous cyclic hardening, and this difference was explained in terms of the residual stress removal and dislocation behaviour. Scanning electron microscopy studies of fatigue fracture surface showed that weld defects of large size and near weld surface were detrimental to the L.C.F. behaviour of weldment.

• 소성∙가공
• /
• 제26권5호
• /
• pp.286-292
• /
• 2017

Magnesium alloy shows strong anisotropy and asymmetric behavior in tension and compression curve, especially at room temperature. These characteristics limit the application of finite element method (FEM) which is based on conventional continuum mechanics. To accurately predict the material behavior of magnesium alloy at microstructural level, a methodology of fully coupled multiscale simulation is presented and a crystal plasticity model as a constitutive equation in the simulation of metal forming process is introduced in this study. The existing constitutive equation for rigid plastic FEM is modified to accommodate deviatoric stress component and its derivatives with respect to strain rate components. Viscoplastic self-consistent (VPSC) polycrystal model was selected as a constitutive model because it was regarded as the most robust model compared to Taylor model or Sachs model. Stiffness matrix and load vector were derived based on the new approach and implemented into $DEFORM^{TM}-3D$ via a user subroutine handling stiffness matrix at an elemental level. The application to extrusion and rolling process of pure magnesium is presented in this study to assess the validity of the proposed multiscale process.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2002년도 추계학술대회 논문집
• /
• pp.693-696
• /
• 2002

This study examined the effects of the testing temperature on the mechanical properties of the carbon tool steel (SK4M) for flat spring. Hardness test and fatigue test were performed at room temperature ($20^{\circ}C$). Tensile test and creep test were performed at temperature range $20^{\circ}C$ ~$160^{\circ}C$. The micro-vickers hardness values of SK4M was Hv=584. The Elastic modulus, tensile strength and yield strength of SK4M at 160t test temperature were decreased 0.92 time, 0.97 time and 0.82 time those of SK4M at 2$0^{\circ}C$ test temperature, respectively. The maximum creep strain for 100hr at creep temperature ($80^{\circ}C$ ~$160^{\circ}C$) and creep stress ($37.4Kgf/\textrm{mm}^2$ ~$93.6Kgf/\textrm{mm}^2$) was 0.572%. The fatigue limit of SK4M was $94Kgf/\textrm{mm}^2$.

• 한국진공학회지
• /
• 제17권5호
• /
• pp.381-386
• /
• 2008

W(110) 표면에 성장한 Co 박막에서 원자 정역학을 주사터널링 현미경으로 연구했다. 원자섬의 개수 밀도를 측정하여 원자 확산 계수의 비를 알 수 있었다. W(110) 표면, Co가 1 원자층 성장된 표면, Co가 2 원자층 성장된 표면의 원자 확산 계수의 비는 상온에서 1:124:33000인 것으로 측정되었다. Co가 2 원자층 성장된 표면의 확산 계수가 Co 가 1 원자층 성장된 표면의 확산 계수보다 큰 것은 이종성장의 스트레인 효과로 인한 것으로 해석되었다.

• 한국분말재료학회지
• /
• 제14권6호
• /
• pp.362-366
• /
• 2007

Magnesium and magnesium alloys are promising materials for light weight and high strength applications. In order to obtain homogeneous and high quality products in powder compaction and powder forging processes, it is very important to control density and density distributions in powder compacts. In this study, a model for densification of metallic powder is proposed for pure magnesium. The mode] considers the effect of powder characteristics using a pressure-dependent critical density yield criterion. Also with the new model, it was possible to obtain reasonable physical properties of pure magnesium powder using cold iso-state pressing. The proposed densification model was implemented into the finite element method code. The finite element analysis was applied to simulating die compaction of pure magnesium powders in order to investigate the density and effective strain distributions at room temperature.

• 한국표면공학회지
• /
• 제48권4호
• /
• pp.142-148
• /
• 2015

The effect of equal channel angular pressing (ECAP) on the pitting corrosion resistance of hard anodized Al5052 alloy was investigated. The degree of internal stress generated in anodic oxide films during hard anodization was also evaluated with a strain gauge method. The pitting corrosion resistance of hard anodized Al5052 alloy was greatly decreased by ECAP. Cracks occurred in the anodic oxide film during hard anodization and these cracks were larger and deeper in the alloy with ECAP than without. The pitting corrosion was accelerated by cracks. The internal stress present in the anodic oxide films was compressive and the stress was higher in the alloys with ECAP than without, resulting in an increased likelihood of cracks. The pitting corrosion resistance of hard anodized Al5052 alloy was improved by annealing at the range of 473-573K after ECAP processed at room temperature for four passes. The compressive internal stress gradually decreased with increasing annealing temperature. It is assumed that the improvement in the pitting corrosion resistance of hard anodized Al5052 alloy by annealing may be attributed to a decrease in the likelihood of cracks due to the decreased internal stresses in anodic oxide films.

• 한국식품조리과학회지
• /
• 제23권1호통권97호
• /
• pp.78-82
• /
• 2007

Yulmoo Kimchi becomes sour without carbonated taste when ripened at room temperature after being placed under cold temperature. The carbonated taste of Kimchi is reported to come from the hetero lactic fermentation of Leuconostoc strains. Yulmoo extract was made with methanol and added to four lactic bacteria strains originating from kimchi. The bacteria were also subjected to $1^{\circ}C$ for 24 hours as a cold shock treatment. after which Leuconostoc mesenteroide subsp. dextranicum KCCM 40708, Lactobacillus brevis KCTC 3102, Lactobacillus plantarum KCTC 3108, and Leuconostoc lactics KCTC 3528 strains showed a growth inhibition with the addition of Yulmoo extract at the concentration of 250-4,000 ppm. Leuconostoc mesenteroide subsp. dextranicum KCCM 40708, Lactobacillus brevis KCTC 3102, Lactobacillus plantarum KCTC 3108, and Leuconostoc lactics KCTC 3528, a strains appearing at the early stage of Kimchi fermentation, showed a higher growth inhibition following Yulmoo treatment in combination with the cold shock.

• 한국세라믹학회지
• /
• 제34권6호
• /
• pp.620-628
• /
• 1997

The possibility of the existence of a field-induced micro-macrodomain switching was proposed and examined using 9 mol % PbZrO3-doped 0.6Pb(Ni1/3Nb2/3)O3-PbTiO3 (PNN-PT) systems having rhombohedral symmetry at room temperature. the thermally depoled (freshly prepard) specimens prepared from the rhombohedral side of the system exhibited a relaxor behavior for the whole range of temperature examined (for T

• 한국신뢰성학회지:신뢰성응용연구
• /
• 제13권2호
• /
• pp.141-151
• /
• 2013

The study of environmental stress cracking (ESC) by contact with plastic rulers and PVC erasers which was artificially added to the external stress was carried out in order to accelerate the chemicals crack. To analyze a blooming plasticizer that migrates from the inside of blended eraser to the surface of the eraser, the ESC experiments were carried out at room temperature and $50^{\circ}C$ conditions. The chemicals crack shape caused by the plasticizer and the brittle fracture shape resulted from the external stress were observed in consequence with the cross-sectional surface analysis of the ruler crack by the ESC. The bending strength of the plastic rulers were fractured prior to the yield point and it had low bending flexure stress. We presented that ESC of polymer materials was affected by the polarity of the chemicals and polymer, the exposure time to chemicals, the exposure temperature and the level of strain on the polymer.