• 자원환경지질
• /
• 제20권4호
• /
• pp.213-221
• /
• 1987

The Donghae mine locates at Jangjoari, Koseongun, Kyongsang-nam-do. The geology of the mine consists of the upper part of Chin dong Formation conformably overlain by tuffaceous Koseong Formation. These formations are intruded by the granodiorite and the basic dikes. The ore mineralization occurs in the fault breccia pipe at the center of a granodiorite stock. The estimated dimension of the breccia pipe is $7m{\times}70m{\times}200m$. The host rock has distinctive hydrothermal alteration halos consisting hematite zone, chlorite zone, epidote zone and sericite zone from outer zone to the ore vein. The ore mineralization occurred in the three distinctive stages. The ore minerals formed in the first stage are pyrite, sphalerite, chalcopyrite, stannite and tetrahedrite. Galena and arsenopyrite are formed in the second stage. Some sphalerite grains include exsolution dots of the chalcopyrite. It is suggested that the ore mineralization occurred by a boiling of a hydrothermal fluid during its initial stage and subsequent cooling and $CO_2$ fugacity drop of remaining hydrothermal fluid by a ground water mixing aided vertical zoning of the ore minerals.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2007년 가을학술발표회
• /
• pp.603-610
• /
• 2007

It is well known that the standard penetration test (SPT) has been used in all over the world to get geotechnical properties of the ground. However, it is difficult to apply the SPT to the dense sand, gravel, weathered rock, etc. For the application of the SPT in these grounds, it is necessary to change in the diameter and the impact energy of the SPT. For the improvement of site investigation technology, Large Penetration Testing device (KICT-type LPT) was developed and applied to the in situ condition. The drop height and weight of the hammer in developed system were decided as 760 mm and 150 kg, respectively. Semi-auto hammer drop system identical with KS F2307 and JI A1259S was adopted. And the developed sampler has the inner diameter of 63 mm and the length of 500 mm with the adjustment of energy ratio to the SPT of 1.5. The hammer energy level was measured during the performance of the KICT-type LPT using SPI system (quality control system from driven piles).

• Computers and Concrete
• /
• 제22권1호
• /
• pp.123-132
• /
• 2018

Reinforced concrete (RC) columns which are the main vertical structural members are exposed to several static and dynamic effects such as earthquake and wind. However, impact loading that is sudden impulsive dynamic one is the most effective loading type acting on the RC columns. Impact load is a kind of impulsive dynamic load which is ignored in the design process of RC columns like other structural members. The behavior of reinforced concrete columns under impact loading is an area of research that is still not well understood; however, work in this area continues to be motivated by a broad range of applications. Examples include reinforced concrete structures designed to resist accidental loading scenarios such as falling rock impact; vehicle or ship collisions with buildings, bridges, or offshore facilities; and structures that are used in high-threat or high-hazard applications, such as military fortification structures or nuclear facilities. In this study, free weight falling test setup is developed to investigate the behavior effects on RC columns under impact loading. For this purpose, eight RC column test specimens with 1/3 scale are manufactured. While drop height and mass of the striker are constant, application point of impact loading, stirrup spacing and concrete compression strength are the experimental variables. The time-history of the impact force, the accelerations of two points and the displacement of columns were measured. The crack patterns of RC columns are also observed. In the light of experimental results, low-velocity impact behavior of RC columns were determined and interpreted. Besides, the finite element models of RC columns are generated using ABAQUS software. It is found out that proposed finite element model could be used for evaluation of dynamic responses of RC columns subjected to low-velocity impact load.

• 한국토양비료학회지
• /
• 제28권3호
• /
• pp.278-286
• /
• 1995

토양(土壤)에 축적(蓄積)되어 있는 난용성(難溶性) 인산염(燐酸鹽)을 이용(利用)하고자 인산염(燐酸鹽) 가용화능(可溶化能)을 가지고 있는 Pseudomonas putida, Penicillium속(屬) 및 Aspergillus niger를 우리 나라 주요(主要) 경작지(耕作地) 토양(土壤)에서 분리(分離)하여 이들 균(菌)의 용해능(溶解能)을 측정(測定)하였다. 인산염(燐酸鹽) 용해량(溶解量)은 배지내(培地內)의 pH 저하(低下)와 밀접(密接)한 관계(關係)를 가지고 있었다. Pseudomonas putida, Penicillium속(屬)에 비(比)해 Aspergillus niger의 인산염(燐酸鹽) 가용화능(可溶化能)이 높았다. Aspergillus niger에 의한 인산염(燐酸鹽) 종류별(種類別) 최대(最大) 가용화량(可溶化量)은 질소원(窒素源)이 $KNO_3$일 때는 aluminium phosphate 776ppm, hydroxyapatite 665ppm, tai-calcium phosphate 593ppm이었으며 인광석(燐鑛石)은 질소원(窒素源)이 $(NH_4)_2SO_4$일 때 411ppm이었다.

• Smart Structures and Systems
• /
• 제30권1호
• /
• pp.49-62
• /
• 2022

Experimental and discrete element methods were used to investigate the effects of triple joints lengths and triple joint angle on the failure behavior of rock mass under uniaxial compressive test. Concrete samples with dimension of 20 cm × 20 cm × 5 cm were prepared. Within the specimen, three imbedded joint were provided. The joint lengths were 2 cm, 4cm and 6 cm. In constant joint lengths, the angle between middle joint and other joints were 30°, 60°, 90°, 120° and 150°. Totally 15 different models were tested under compression test. The axial load rate on the model was 0.05 mm/min. Concurrent with experimental tests, the models containing triple joints, length and joint angle are similar to the experiments, were numerical by Particle flow code in two dimensions (PFC2D). Loading rate in numerical modelling was 0.05 mm/min. Tensile strength of material was 1 MPa. The results show that the failure behaviors of rock samples containing triple joints were governed by both of the angle and the length of the triple joints. The uniaxial compressive strengths (UCS) of the specimens were related to the fracture pattern and failure mechanism of the discontinuities. Furthermore, it was shown that the compressive behavior of discontinuities is related to the number of the induced tensile cracks which are increased by decreasing the joint length. Along with the damage failure of the samples, the acoustic emission (AE) activities are excited. There were only a few AE hits in the initial stage of loading, then AE hits rapidly grow before the applied stress reached its peak. In addition, every stress drop was accompanied by a large number of AE hits. Finally, the failure pattern and failure strength are similar in both methods i.e., the experimental testing and the numerical simulation methods.

• Geomechanics and Engineering
• /
• 제29권5호
• /
• pp.567-582
• /
• 2022

In the present study, a series of physical experiments and numerical simulations were conducted to investigate the effects of mode I and mixed-mode I/II cracks on the fracture modes and stability of roadway tunnel models. The experiments and simulations incorporated different inclination angle flaws under both static and dynamic loads. The quasi-static and dynamic testing were conducted by using an electro-hydraulic servo control device and drop weight impact system (DWIS), and the failure process was simulated by using rock failure process analysis (RFPA) and AUTODYN software. The stress intensity factor was also calculated to evaluate the stability of the flawed roadway tunnel models by using ABAQUS software. According to comparisons between the test and numerical results, it is observed that for flawed roadways with a single radical crack and inclination angle of 45°, the static and dynamic stability are the lowest relative to other angles of fractured rock masses. For mixed-mode I/II cracks in flawed roadway tunnel models under dynamic loading, a wing crack is produced and the pre-existing cracks increase the stress concentration factor in the right part of the specimen, but this factor will not be larger than the maximum principal stress region in the roadway tunnel models. Additionally, damage to the sidewalls will be involved in the flawed roadway tunnel models under static loads.

• 한국생물공학회:학술대회논문집
• /
• 한국생물공학회 2003년도 생물공학의 동향(XIII)
• /
• pp.384-387
• /
• 2003

음식물쓰레기 퇴비화시설에서 발생하는 악취에 대해 90일 동안 입구농도를 측정한 결과 발효기 가동시간에는 $10{\sim}100ppm$, 비가동시간에는 $0{\sim}10ppm$의 농도를 나타냈다. 바이오필터의 제거효율은 초기에 80%정도를 보이다 20일 전후를 해서 90%이상을 나타냈다. 압력손실은 90일 경과 후에도 20 $mmH_2O$를 넘지 않아 바이오필터에 효율적인 악취처리가 이루어졌음을 알 수 있다.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2008년도 추계 학술발표회
• /
• pp.1359-1364
• /
• 2008

It is well known that the standard penetration test (SPT) has been used in all over the world to get geotechnical properties of the ground. However, it is difficult to apply the SPT to the dense sand, gravel, weathered rock, etc. For the application of the SPT in these grounds, it is necessary to change in the diameter and the impact energy of the SPT. For the improvement of site investigation technology, Large Penetration Testing device (KICT-type LPT) was developed and applied to the in situ condition. The drop height and weight of the hammer in developed system were decided as 760mm and 150kg, respectively. And the developed sampler has the inner diameter of 63 mm and the length of 500 mm with the adjustment of energy ratio to the SPT of 1.5. In this study, the performance of KICT-type LPT was evaluated by using a calibration chamber system and pile driving analyzer (PDA)

• 방사성폐기물학회지
• /
• 제4권3호
• /
• pp.301-309
• /
• 2006

한국형처분시스템에 이용될 가압경수로형 사용후핵연료를 위한 KDC-1 처분용기를 개발하였다. 처분용기 안전성 평가의 일환으로서 처분용기에 대한 구조적 안전성을 평가하였다. 처분용기의 구조적 안전성은 처분조건과 취급조건 2가지로 구분하여 평가하였다. 처분조건에서는 3가지 하중 조건, 정상하중 조건, 비정상 하중 조건, 암반의 움직임을 고려하였다. 처분조건에서 평가 결과 3가지 조건에 대해 모두 안전계수가 설계기준보다 컸다. 취급조건에서는 처분용기 취급 중 구조해석과 처분용기 낙하 사고시 구조해석을 수행하였다. 취급장비 고장 시나리오 평가결과 1개 혹은 2개의 취급 장치가 고장을 일으켰을 때도 취급장비를 계속 운전하는 것이 가능하였다. 처분용기 낙하 시나리오에서는 계산결과 최대 응력은 0.762 MPa 이었으며, 이 값은 주철의 항복응력과 비교하면 거의 무시할 수 있는 값이었다. 본 논문에서 제안한 KDC-1 처분용기에 대한 처분조건 및 취급조건에서의 구조해석 결과, 한국형처분시스템에서 고려하고 있는 조건에서 그 구조적 안전성을 확인하였다.

• 지질공학
• /
• 제13권3호
• /
• pp.321-334
• /
• 2003

본 연구는 암반에서 불연속면 방향의 효율적인 측정 방안에 관한 것이다. 불연속면의 방향성은 주향/경사, 경사방향/경사(세 자리 숫자/두 자리 숫자) 그리고 경사방향을 우측에 두고 바라보는 방향을 주향방향으로 결정하는 방법의 세 가지 방법으로 표현한다. 일반적으로 불연속면의 주향/경사는 클리노미터에 의해 측정이 되며, 경사방향』경사는 실바콤파스(type15)에 의해 측정된다. 주향/경사는 지질조사시에 측정이 되는데, 경사방향/경사는 공학적 목적으로 측정이 되며, 통계처리에 유용하다 클리노미터에 의해 불연속면의 경사방향 측정과 주향/경사를 경사방향/경사로의 전환 시, 측정자에 따라 오류를 유발할 가능성이 있다. 본 연구에서는 불연속면 방향성을 두 가지 방법 (주향/경사. 경사방향/경사)으로 효과적으로 측정하기 위하여 클리노미터에 회전방위판과 주향 및 경사방향 표시 화살표를 부착하여 측정하는 방법을 고안하였다. 이 새로운 측정법은 주향뿐만 아니라 경사방향을 정확하게 측정할 수 있는 효과적인 측정법이다. 또한 이 측정법은 주향/경사 및 경사방향/경사의 동시 측정이 가능하다. 암반사면에서 불연속면의 방향 측정 시, 현행 측정법과 새로운 측정법을 비교한 결과. 새로운 측정법이 오류를 분명히 감소시킴을 알 수 있었다 따라서 새로운 측정법은 도로 설계 시 광역적인 지표지질조사에서 많은 불연속면의 방향성을 측정할 경우와 측정 경험이 부족한 조사자에게 유용한 방법이라고 생각된다.