• 제어로봇시스템학회:학술대회논문집
• /
• 2000.10a
• /
• pp.44-44
• /
• 2000

Firstly, kinematic model of various type of wheels which includesskidding and skidding friction are presented. Tend, the transfer method of generalized coordinates which is useful to model the parallel mechanisms, can be applied to mobile robot by including such friction terms. Particularly, by appling the modeling method to mobile robot consisting of two conventional wheels and one caster wheel, forword/reverse kinematic modeling could be obtained without using pseudoinverse solutions.

• International Journal of Control, Automation, and Systems
• /
• v.6 no.1
• /
• pp.86-100
• /
• 2008

Most of the previously employed dynamic modeling approaches, including Natural Orthogonal Complement Algorithm, have limitations on their application to the mobile robot, specifically at singular configurations. Also, in their dynamic modeling of mobile robots, wheel dynamics is usually ignored assuming that its dynamic effect is negligibly small. As a remedy for this, a singularity-free operational space dynamic modeling approach based on Lagrange's form of the D' Alembert principle is proposed, and the singularity-free characteristic of the proposed dynamic modeling is discussed in the process of analytical derivation of the proposed dynamic model. Then an accurate dynamic model taking into account the wheel dynamics of the omni-directional mobile robot is derived, and through simulation it is manifested that the effect of the wheel dynamics on the whole dynamic model of the mobile robot may not be negligible, but rather in some cases it is significantly large, possibly affecting the operational performances of dynamic model-based control algorithms. Lastly, the importance of its accurate dynamic model is further illustrated through impulse analysis and its simulation for the mobile robot.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2005.05a
• /
• pp.883-889
• /
• 2005

Micro robots have been developed for many applications: medical, industrial, military, and so on. A small mobile robot was built and it has three legs made of bimorph piezoelectric actuators. It proceeds by vibrating the rear leg and it rotates by vibrating one of the front legs. The locomotion of the robot is described by relative position of mass center and the friction between the legs and the floor. This paper describes the principles of locomotion and modeling of the robot Modeling was simulated to investigate the dynamics of its mobility. The simulation results verified the modeling by showing similar movement of the robot as measured. It remained, however, several problems through experiments such as crooked direction of forward movement and proceeding speed.

• 제어로봇시스템학회:학술대회논문집
• /
• 2000.10a
• /
• pp.343-343
• /
• 2000

The conventional actuators with the speed reducer had weakness in supporting the weight of the body and leg itself. To overcome this, a new four bar link mechanism actuated by the ball screw was proposed. Using this, we developed a new type of 10 D.O.F biped robot. The dynamics model of the biped robot is investigated in this paper. In the modeling process, the robot dynamics are expressed in the joint coordinates using the Euler-Lagrange equation. Then, they are converted in to the sliding joint coordinates, and joint torques are expressed in the force along the sliding direction of the ball screw. To test modeling of the robot, a computer simulation was performed.

• Journal of Institute of Control, Robotics and Systems
• /
• v.4 no.5
• /
• pp.636-643
• /
• 1998

This paper is presents multivariable control scheme for industrial robot manipulators. The control scheme consists of two loops. The modeling error between linearized robot model and actual robot model is compensated in error compensation loop. The PID control loop is designed for pole assignment to stability of robot system and utilized for trajectory tracking. Alternatively computer simulation results are given for illustration purpose of suggested controller.

• 제어로봇시스템학회:학술대회논문집
• /
• 2001.10a
• /
• pp.59.5-59
• /
• 2001

Multi-agent robot system is the system which executes by cooperating with each robots and controlling several robots. Capability and function of each robot must be considered for cooperation behavior. Furthermore, it is necessary to analyze the given environment and to replace complex task with some simple tasks. Analysis of the given environment and role assignment for the given tasks are composed of discret event. In this paper, the hierarchical controller for multi-agent robot system using the petri-net state diagram is proposed. The proposed modeling method is implemented for soccer robot system. The effectiveness of proposed modeling method is shown through experiment.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.2 no.4
• /
• pp.222-227
• /
• 2007

Applies the open type object modeling and a profile ring technique of ISO15754 standards and develops the development methodology which liberralizes about plan and embodiment of the humanoid robot which proposes.

• Journal of Institute of Control, Robotics and Systems
• /
• v.13 no.4
• /
• pp.320-328
• /
• 2007

This paper presents a stiffness modeling of a low-DOF parallel robot, which takes into account of elastic deformations of joints and links, A low-DOF parallel robot is defined as a spatial parallel robot which has less than six degrees of freedom. Differently from serial chains in a full 6-DOF parallel robot, some of those in a low-DOF parallel robot may be subject to constraint forces as well as actuation forces. The reaction forces due to actuations and constraints in each serial chain can be determined by making use of the theory of reciprocal screws. It is shown that the stiffness of an F-DOF parallel robot can be modeled such that the moving platform is supported by 6 springs related to the reciprocal screws of actuations (F) and constraints (6-F). A general $6{\times}6$ stiffness matrix is derived, which is the sum of the stiffness matrices of actuations and constraints, The compliance of each spring can be precisely determined by modeling the compliance of joints and links in a serial chain as follows; a link is modeled as an Euler beam and the compliance matrix of rotational or prismatic joint is modeled as a $6{\times}6$ diagonal matrix, where one diagonal element about the rotation axis or along the sliding direction is infinite. By summing joint and link compliance matrices with respect to a reference frame and applying unit reciprocal screw to the resulting compliance matrix of a serial chain, the compliance of a spring is determined by the resulting infinitesimal displacement. In order to illustrate this methodology, the stiffness of a Tricept parallel robot has been analyzed. Finally, a numerical example of the optimal design to maximize stiffness in a specified box-shape workspace is presented.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2005.06a
• /
• pp.806-811
• /
• 2005

The robot to search and rescue is used in narrow space where human cannot approach. In case of this robot, it can overcome obstacles such as wrecks or stairs etc. Also, this robot can do various locomotion for each object. In this reason, an articulated robot has advantages comparing with one module robot. However, the existing articulated robot has limits to overcome vertical passages. For expanding contacted territory of robot, a novel mechanism is demanded. In this paper, the novel mechanism of articulated mobile robot is designed for moving level ground and vertical passages. This paper proposes to change wheel alignment. The robot needs two important motions for passing vertical passages like pipe. One is a motion to press wheels at wall for not falling into gravity direction. The other is a motion that wheels contact a vertical direction of wall's tangential direction for reducing loss of force. The mechanism of the robot focused that two motions can be acted to use just one motor. Length of each link of robot is optimized that wheels contact a vertical direction of wall's tangential direction through kinematic modeling of each link. The force of pressing wall of robot is calculated through dynamic modeling. This robot composes four modules. This mechanism is confirmed by dynamic simulation using ADAMS program. The articulated mobile robot is elaborated based on the results of kinematic modeling and dynamic simulation.

• Proceedings of the Korean Institute of Intelligent Systems Conference
• /
• 1998.03a
• /
• pp.127-130
• /
• 1998

In this paper, we propose a method of cooperative control(T-cell modeling) and selection of group behavior strategy(B-cell modeling) based on immune system in distributed autonomous robotic system(DARS). Immune system is living body's self-protection and self-maintenance system. Thus these features can be applied to decision making of optimal swarm behavior in dynamically changing environment. For the purpose of applying immune system to DARS, a robot is regarded as a B cell, each environmental condition as an antigen, a behavior strategy as an antibody and control parameter as a T-call respectively. The executing process of proposed method is as follows. When the environmental condition changes, a robot selects an appropriate behavior strategy. And its behavior strategy is stimulated and suppressed by other robot using communication. Finally much stimulated strategy is adopted as a swarm behavior strategy. This control scheme is based of clonal selection and idiotopic network hypothesis. And it is used for decision making of optimal swarm strategy. By T-cell modeling, adaptation ability of robot is enhanced in dynamic environments.