• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2002년도 추계학술대회 논문집 Vol.15
• /
• pp.370-374
• /
• 2002

Many compound semiconductors which have high carrier mobility and small band gap have attentive in application of various practical a field. Especially, InSb served for Hall device and magnetic resistor such as magnetic sensor because InSb thin film has high mobility. Many studies on InSb thin film deposistion because In and Sb has been very different feature of vapor pressure ($10^{-4}$ times) When In and Sb deposited. In this paper studied it In and Sb deposited simultaneously using by method of co-sputtering deposotion. This process, get to effects of manufacture process simplification. After that this paper observed micro structure and electronic behavior of InSb thin film using by co-sputtering and we study properties of magneto-resistance by annealing.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2002년도 제4회 영호남학술대회 논문집
• /
• pp.128-132
• /
• 2002

Many compound semiconductors which have high carrier mobility and small band gap have attentive in application of various practical a field. Especially, InSb served for Hall device and magnetic resistor such as magnetic sensor because InSb thin film has high mobility. Many studies on InSb thin film deposistion because In and Sb has been very different feature of vapor pressure($10^{-4}$ times) When In and. Sb deposited. In this paper studied it In and Sb deposited simultaneously using by method of co-sputtering deposotion. This process, get to effects of manufacture process simplification. After that this paper observed micro structure and electronic behavior of InSb thin film using by co-sputtering and we study properties of magneto-resistance by annealing

• 대한전자공학회논문지
• /
• 제23권3호
• /
• pp.364-369
• /
• 1986

Silicon diaphragms, 10 and 20 \ulcorner-thick and 1x1 mm\ulcornerarea, have been fabricated by means of the electrochemical P-N junction etch-stop technique. The P-type diffused resistors were formed on the diaphragm, and the piezoresistance effect was examined. It was been found that the fractional variation of the resistance is dependent on the diaphragm thickness, resistor location, and resistor length, etc. The 1.2 k\ulcornerfull-brige pressure sensor with 10\ulcorner-thick diaphragm exhibits a pressure sensitivity of 42 \ulcorner/V\ulcornermHg with a temperature coefficient of 2.3 mmHg/\ulcorner, and shows a good linearity in the pressure range from 0 to 300 mmHg.

• 로봇학회논문지
• /
• 제5권4호
• /
• pp.294-301
• /
• 2010

In order to produce a convenient robot for the aged and the lower limb disabled, it is needed for the research detecting implicit walking intention and controlling robot by a user's intention. In this study, we developed sensor module system to control the walking- assist robot using FSR sensor and tilt sensor, and analyzed the signals being acquired from two sensors. The sensor module system consisted of the assist device control unit, communication unit by wire/wireless, information collection unit, information operation unit, and information processing PC which handles integrated processing of assist device control. The FSR sensors attached user's the palm and the soles of foot are sensing force/pressure signals from these areas and are used for detecting the walking intention and states. The tilt sensor acquires roll and pitch signal from area of vertebrae lumbales and reflects the pose of the upper limb. We could recognize the more detailed user's walking intention such as 'start walking', 'start of right or left foot forward', and 'stop walking' by the combination of FSR and tilt signals can recognize.

• 전자공학회논문지A
• /
• 제31A권5호
• /
• pp.113-120
• /
• 1994

Silicon flow sensor that can detect the velocity and direction of air flow was designed and fabricated by integrated circuit process and bulk micromachining technique. The flow sensor consists of three-layered dielectric diaphragm, a heater at the center of the diaphragm, and four thermopiles surrounding the heater at each side of diaphragm as sensing elements. This diaphragm structure contributes to improve the sensitivity of the sensor due to excellent thermal isolation property of dielectric materials and their tiny thickness. The flow sensor has good axial symmetry to sense 2-D air flow with the optimized sensing position in the proposed structure. The sensor is fabricated using CMOS compatible process followed by the anisotropic etching of silicon in KOH and EDP solutions to form I$\mu$ m thick dielectric diaphragm as the last step. TCR(Temperature Coefficient of Resistance) of the heater of the fabricated sensors was measured to calculate the operating temperature of the heater and the output voltage of the sensor with respect to flow velocity was also measured. The TCR of the polysilicon heater resistor is 697ppm/K, and the operating temperature of the heater is 331$^{\circ}C$ when the applied voltage is 5V. Measured sensitivity of the sensor is 18.7mV/(m/s)$^{1/2}$ for the flow velocity of smaller than 10m/s.

• 전자공학회논문지
• /
• 제50권12호
• /
• pp.80-87
• /
• 2013

저가, 광대역, 그리고 넓은 이득 제어 범위를 갖는 전자 계측 시스템을 실현하기 위한 정극성 전류 컨베이어(positive polarity current-conveyor : CCII+)를 사용한 새로운 계측 증폭기(instrumentation amplifier : IA)를 설계하였다. 이 IA는 두 개의 CCII+, 세 개의 저항 그리고 한 개의 연산 증폭기(operational amplifier : op-amp)로 구성된다. 동작 원리는 두 입력 전압의 차가 전압 및 전류 폴로워(follower) 사용되는 두 개의 CCII+에 의해 각각 동일한 전류로 변환되고 이 전류는 op-amp의 (+)단자의 저항기와 귀환 저항기를 통과시켜 출력 전압을 구하는 것이다. IA의 동작 원리를 확인하기 위해 AB급 CCII+를 설계하였고 상용 op-amp LF356을 사용하여 IA를 구현하였다. 시뮬레이션 결과 CCII+를 사용한 전압 폴로워는 ${\pm}$4V의 선형범위에서 0.21mV의 오프셋 전압을 갖고 있었다. IA는 1개의 저항기의 저항값 변화로 -20dB~+60dB의 이득을 갖고 있으며, 60dB에 대한 -3dB 주파수는 400kHz이였다. 제안한 IA의 외부의 저항기의 정합이 필요 없고 다른 저항기로 오프셋을 조절할 수 있는 장점을 갖고 있다. 소비전력은 ${\pm}$5V 공급전압에서 130mW이였다.

• 전자공학회논문지
• /
• 제53권1호
• /
• pp.59-67
• /
• 2016

저가, 광대역, 그리고 넓은 이득 제어 범위를 갖는 전자 계측 시스템을 실현하기 위한 완전-차동 선형(fully-differential linear operational transconductance amplifier : FLOTA)를 사용한 새로운 계측 증폭기(instrumentation amplifier : IA)를 설계하였다. 이 IA는 한 개의 FLOTA, 두 개의 저항 그리고 한 개의 연산 증폭기(operational amplifier : op-amp로 구성된다. 동작 원리는 FLOTA에 인가되는 두 입력 전압의 차가 각각 동일한 차동 전류로 변환되고 이 전류는 op-amp의 (+)단자의 저항기와 귀환 저항기를 통과시켜 단일 출력 전압을 구하는 것이다. 제안한 IA의 동작 원리를 확인하기 위해 FLOTA를 설계하였고 상용 op-amp LF356을 사용하여 IA를 구현하였다. 시뮬레이션 결과 FLOTA를 사용한 전압-전류 특성은 ${\pm}3V$의 입력 선형 범위에서 0.1%의 선형오차와 2.1uA의 오프셋 전류를 갖고 있었다. IA는 1개의 저항기의 저항 값 변화로 -20dB~+60dB의 이득을 갖고 있으며, 60dB에 대한 -3dB 주파수는 10MHz이였다. 제안한 IA의 외부의 저항기의 정합이 필요 없고 다른 저항기로 오프셋을 조절할 수 있는 장점을 갖고 있다. 소비전력은 ${\pm}5V$ 공급전압에서 105mW이였다.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2002년도 ITC-CSCC -1
• /
• pp.341-344
• /
• 2002

This paper is proposed a 8-bit analog to digital converter for CMOS image sensor. A analog to digital converter for CMOS image sensor is required function to control gain. Frequency divider is used In control gain in this proposed analog to digital converter. At 3.3 Volt power supply, total static power dissipation is 8㎽ and programmable gain control range is 30㏈. Newly suggested analog to digital converter is designed by 0.35um 2-poly 4-metal CMOS technology.

• 센서학회지
• /
• 제29권2호
• /
• pp.75-81
• /
• 2020

We introduce a new visible light communication (VLC) method in which three-level return-to-zero (RZ) modulation is used for flicker-free transmission. In the VLC transmitter, the three-level RZ modulation ensures that the average optical power is constant; thus, a flicker-free light-emitting diode (LED) light is achieved. In the VLC receiver, a resistor-capacitor high-pass filter is used for generating spike signals, which are used for data recovery while eliminating the 120 Hz optical noise from adjacent lighting lamps. In transmission experiments, we applied this method for wireless transmission of an air quality sensor message using the visible light of an LED array. This configuration is useful for the construction of indoor wireless sensor networks for air pollution monitoring using LED lights.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2002년도 하계학술대회 논문집 Vol.3 No.2
• /
• pp.699-702
• /
• 2002

A DC current sensor is disclosed in which two pairs of saturable cores are provided so as enclose a conductor carrying a direct current to be measured. On each of the saturable cores, a bias winding, a feedback winding and an output winding are wound. Circuit for detection of an asymmetry in the magnetization current, generated by a reference alternating voltage, in a signal-conditioner. The reference alternating voltage is fed to the respective series circuits such that no resultant induction current is induced in the modulating current. The voltages over the resistor form input signals for two peak value detectors, the strength of the output signal of which represents the degree of asymmetry of magnetization current. This paper describes the development a DC current sensor and its signal-conditioner.