• 설비공학논문집
• /
• 제21권8호
• /
• pp.462-467
• /
• 2009

Researches and developments on BEMS are performed world-widely through sustainable management in various conditions. However, there are many obstacles to adapt the system in existing buildings because it needs highly expensive equipments, which are designed for newly built buildings, to install. Therefore, there are numerous limits exist when applying the BEMS in established buildings. The purpose of this study estimates the optimization of RF output power in WSN(Wireless Sensor Networks), which is the essential technology to develop PEMS. The results of this study is as follows ; 1) Applying WSN technique in buildings was possible. 2) As RF output power increases, the number of relay node reduced, therefore, the WSN showed more stability. 3) When estimating optimal RF output power in school, it should be considered between the number of relay node and RF output power. 4) Considering battery consumption and possibility of reception, the best suited RF output power is -20dbm in apartment house.

• Journal of Power Electronics
• /
• 제18권1호
• /
• pp.266-276
• /
• 2018

This paper presents a new step-up and step-down multi-pulse auto-transformer rectifier unit (ATRU) topology. This structure can achieve a wide range of output voltages, which solves the problem of auto-transformer output voltage being difficult to regulate. Adding middle taps to the primary winding and reasonably setting the number of auto-transformer windings, constituted two groups of three-phase output voltages with a $30^{\circ}$ phase difference. Multi-pulse output DC voltage is obtained after a three-phase output voltage across two rectifier bridges and inter-phase reactor. Thus, the output DC voltage is related to the number and configuration of the auto-transformer winding. In this paper, the relationship between the voltage ratio of the auto-transformer and the ratio of winding, input current and auto-transformer kilovoltampere rating are deduced and validated by simulations. On this basis, the output voltage range is optimized. An experiment on two different voltage ratio principle prototypes was carried out to verify the correctness of the analysis design.

• 전력전자학회논문지
• /
• 제27권1호
• /
• pp.40-47
• /
• 2022

At present, the low-voltage, high-current type power supply is mainly used for effective sterilization in the ballast water treatment system. Research on PSFB converters without output capacitors has been ongoing. Such converters effectively treat ballast water without a separate disinfectant through electric pulses by applying a pulse-type power to the output electrode without an output capacitor. However, in the case of the pulse-type electrolysis treatment method, voltage overshoot can occur due to abrupt voltage fluctuations when the load changes, resulting in circuit reliability problems because of the output capacitorless system. Therefore, a new voltage control algorithm is required. In this paper, we will discuss voltage control for pulsed electrolysis topology without an output capacitor. The proposed voltage control method has been verified using Simulation and experiment. The usefulness of the proposed control method has been proven by the experimental results.

• 한국임상수의학회지
• /
• 제25권5호
• /
• pp.379-384
• /
• 2008

The objective of this study was to determine output power for skin incision in 0.3 mm spot diameter $CO_2$ laser by measuring (1) the wound depth, (2) initial dermal tissue damage, (3) degree of wound healing at different power (4W, 5W and 6W) in beagle dogs. Three healthy 2-year-old beagle dogs were used. Four 2 cm straight skin incisions were made with 0.3 mm spot diameter $CO_2$ laser on the each dog's both side of dorsal midline in three beagle dogs. The skin incisions were performed for $10{\sim}15$ seconds for same dosage. And then each wound was closed with surgical stapler. At 0, 3, 7 and 14 days after initial wounding, each wound was taken for histological observation. On macroscopic and microscopic observation, initial incisional wound did not show difference in three group. And also re-epithelialization, dermal tissue damage and inflammatory response did not show significant difference among groups. This study reveals that 4W, 5W and 6W may be suitable output power in 0.3 mm spot diameter $CO_2$ laser for the skin incision in beagle dogs.

• Journal of Electrical Engineering and Technology
• /
• 제9권3호
• /
• pp.835-842
• /
• 2014

Cutback control in a grid code is one of the functions of a wind power plant (WPP) that is required to support the system protection and frequency stability. When a cutback control command signal is delivered to the WPP from the system operator, the output of a WPP should be decreased to 20% of the rated power within 5 s. In this paper, we propose a dedicated cutback control algorithm of a WPP based on the ratio of the command power to the available power. If a cutback control signal is delivered, the algorithm determines the pitch angle for the cutback control and starts the pitch angle control. The proposed algorithm keeps the rotor speed at the speed before the start of the cutback control to quickly recover the previous output prior to the cutback control. The performance of the algorithm was validated for a 100 MW aggregated WPP based on a permanent magnet synchronous generator under various wind conditions using an EMTP-RV simulator. The results clearly shows that the proposed algorithm not only successfully reduces the output to the command power within 5 s by minimizing the fluctuation of the pitch angle, but also rapidly recovers to the output level before the cutback control.

• International Journal of Control, Automation, and Systems
• /
• 제2권1호
• /
• pp.1-14
• /
• 2004

This paper surveys some existing direct adaptive feedback control schemes for linear time-invariant systems with actuator failures characterized by the failure pattern that some inputs are stuck at some unknown fixed or varying values at unknown time instants, and applications of those schemes to aircraft flight control system models. Controller structures, plant-model matching conditions, and adaptive laws to update controller parameters are investigated for the following cases for continuous-time systems: state tracking using state feed-back, output tracking using state feedback, and output tracking using output feedback. In addition, a discrete-time output tracking design using output feedback is presented. Robustness of this design with respect to unmodeled dynamics and disturbances is addressed using a modified robust adaptive law.

• 경영과학
• /
• 제15권2호
• /
• pp.125-142
• /
• 1998

The aggregation on linear large-scale dynamic systems is examined in this paper and a "two-step" approach is proposed. In this procedure, the aggregated system consists of two subsystems. The first subsystem represents aggregation through the retainment of dominant eigenvalues of the original system, leading to a first approximation of the desired output of the original system. The purpose of augmenting it with a second subsystem is to provide an estimation of the error on the first approximation, thus permitting a second correction to the output approximation and resulting in an output approximation of greater accuracy. Optimization techniques are discussed for the determination of unknown parameters in the aggregated system. These techniques use minimization principles of certain suitable performance indices and are developed for both single input-single output and multiple input-multiple output system. Numerical examples illustrating these procedures are given and the results are compared with those obtained using existing methods. Finally, a pharmacokinetics problem is studied from the aggregation point of view.

• 기술사
• /
• 제32권6호
• /
• pp.40-43
• /
• 1999

The R&D productivity has the same meaning as that of general meaning. Its input includes budget, facility, schedule, idea and target, and its output includes patent, paper, technological innovation and revenue increase and technology accumulation influenced by these factors. The choice of R&D item which will have the large effectiveness after customization, resource input of proper level, application of efficient development schema, effective usage of development output, objective appraisal for the R&D output and extension for the future project are the main factors for which is suggested to enhance the R&D productivity. The management's expectation for R&D can be represented as the innovativeness of output and potential influence to outsiders. The speedy output, even if incremental investment more than planning happens, will eventually result in the productivity enhancement of the enterprise, and managers must not encounter the opportunity loss in return for the excessive investment control.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2009년도 춘계학술대회 논문집 전기설비전문위원
• /
• pp.189-191
• /
• 2009

In this thesis, output voltage, current and power of solar module were classified by irradiation and module temperature from data of overall operating characteristics collected for one year in order to manage efficient photovoltaic generation system and deliver maximum power. In addition, from these data, correlations between irradiation, module temperature of photovoltaic cell and amount of power given by photovoltaic cell was quantitatively examined to deduce optimization of the design and construction of photovoltaic generation system. The results of this thesis can be summarized as follows. As output power characteristics according to a irradiation range of $100{\sim}900[W/m^2]$, output power was increased with increasing irradiation. This result corresponds well to the related equation on irradiation and output power.

• International Journal of Precision Engineering and Manufacturing
• /
• 제3권3호
• /
• pp.28-36
• /
• 2002

The continuously variable transmission (CVT) mechanism considered here is the output coupled type which combines the functions of a 2K-H I type differential gear unit and a V-belt type continuously variable unit (CVU). One shaft of the CVU is connected directly to the output shaft and another shaft of it is linked to the differential gear unit. It is shown that some fundamental relations (speed ratios, power flows and efficiencies) for twelve mechanisms previously described are valid by various experimental studies, six of them produce a power circulation and the others produce a power split. Parametric analysis is carried out in relation to the efficiency, speed ratio and power ratios in order to assist in the design of an optimum configuration. Some useful properties associated with power flow modes also are discussed in the output coupled type continuously variable transmission.