• Journal of agriculture & life science
• /
• v.44 no.4
• /
• pp.79-85
• /
• 2010

An analysis in heating effects of an electric radiator located in a 1-2W type chrysanthemum (3 cultivars) cultivation greenhouse installed in Gyeongsang National University drew the following conclusions. During the experiment period, the highest, average, and the lowest outside temperatures were in the ranges of $-3.8{\sim}21.3^{\circ}C$, $-5.2{\sim}16.1^{\circ}C$ and $-12.5{\sim}14.4^{\circ}C$, respectively, and the average relative humidity inside and outside the greenhouses were in the ranges of 43.5~98.6% and 35.2~100%, respectively. From mid-December to early February, the lowest outside temperature was recorded as approximately $-5.0{\sim}-10.0^{\circ}C$, which showed that it tended to be relatively lower than the temperatures recorded at the Jinju Meteorological Observatory. During the night, the leaf temperature measured directly under the radiator tended to be higher by $2{\sim}3^{\circ}C$ than that those at the middle point of the radiator, or higher by a negligible amount. In the case of root zone temperature, it was found that there was almost no difference between temperatures of the part directly under and the middle point, and the time when the highest temperature of root zone and other highest temperatures took place showed that there was about a 2-hour delay phenomenon. The total electricity consumption, energy supply and total heating cost during the experiment period were 2,800 kWh, 2,408,000 kcal and 112,000 won, respectively. When diesel, a kind of fossil fuel, was used as heating oil, the total heating cost was around 224,500 won. It was estimated that the total heating cost could be reduced by around 50% if a radiator was used.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.20 no.6
• /
• pp.288-296
• /
• 2019

Radiation cooling has used ceilings or floors as cooling surfaces. In such cases, to avoid moisture condensation on the surface, the surface temperature needs be higher than the dew point temperature or an additional dehumidifier is added. In this study, with a goal for residential application, intentional moisture condensation on the cooling surface was attempted, which increased the cooling capacity and improved the indoor comfortness. This method included two separate refrigeration cycles - convection-type dehumidifying cycle and the panel cooling cycle. Test results on the panel cooling cycle showed that, at the standard outdoor ($35^{\circ}C/24^{\circ}C$) and indoor ($27^{\circ}C/19.5^{\circ}C$) condition, the refrigerant flow rate was 8.8 kg/h, condensation temperature was $51^{\circ}C$, evaporation temperature was $8.8^{\circ}C$, cooling capacity was 376 W and COP was 1.75. Furthermore, the panel temperature was uniform within $1^{\circ}C$ (between $13^{\circ}C$ and $14^{\circ}C$). As the relative humidity decreased, the cooling capacity decreased. However, the power consumption remained approximately constant. In the convection-type dehumidification cycle, the refrigerant flow rate was 21.1 kg/h, condensation temperature was $61^{\circ}C$, evaporation temperature was $5.0^{\circ}C$, cooling capacity was 949 W and COP was 2.11 at the standard air condition. When both the radiation panel cooling and the dehumidification cycle operated simultaneously, the cooling capacity of the radiation panel cycle was 333 W and that of the dehumidification cycle was 894 W, and the COP was 1.89. As the fan flow rate decreased, both the cooling capacity of the radiation panel and the dehumidification cycle decreased, with that of the dehumidification cycle decreasing at a higher rate. Finally, a possible control logic depending on the change of the cooling load was proposed based on the results of the present study.

• Journal of Chest Surgery
• /
• v.52 no.4
• /
• pp.248-329
• /
• 2019

Background: Though clinical practice guidelines (CPGs) for cardiac rehabilitation (CR) are an effective and widely used treatment method worldwide, they are as yet not widely accepted in Korea. Given that cardiovascular disease is the second leading cause of death in Korea, it is urgent that CR programs be developed. In 2008, the Government of Korea implemented CR programs at 11 university hospitals as part of its Regional Cardio-Cerebrovascular Center Project, and 3 additional medical facilities will be added in 2019. In addition, owing to the promotion of CR nationwide and the introduction of CR insurance benefits, 40 medical institutions nationwide have begun CR programs even as a growing number of medical institutions are preparing to offer CR. The purpose of this research was to develop evidence-based CPGs to support CR implementation in Korea. Methods: This study is based on an analysis of CPGs elsewhere in the world, an extensive literature search, a systematic analysis of multiple randomized control trials, and a CPG management, development, and assessment committee comprised of 33 authors-primarily rehabilitation specialists, cardiologists, and thoracic surgeons in 21 university hospitals and 2 general hospitals. Twelve consultants, primarily rehabilitation, sports medicine, and preventive medicine specialists, CPG experts, nurses, physical therapists, clinical nutritionists, and library and information experts participated in the research and development of these CPGs. After the draft guidelines were developed, 3 rounds of public hearings were held with staff members from relevant academic societies and stakeholders, after which the guidelines were further reviewed and modified. Results: CR involves a more cost-effective use of healthcare resources relative to that of general treatments, and the exercise component of CR lowers cardiovascular mortality and readmission rates, regardless of the type of coronary heart disease and type and setting of CR. Conclusion: Individualized CR programs should be considered together with various factors, including differences in heart function and lifestyle, and doing so will boost participation and adherence with the CR program, ultimately meeting the final goals of the program, namely reducing the recurrence of myocardial infarction and mortality rates.

• Korean Journal of Heritage: History & Science
• /
• v.42 no.3
• /
• pp.26-47
• /
• 2009

This study examined dwelling site from among the sites of the Neolithic age found in the Asan Bay(牙山灣) area, and the temporal-spatial location and meaning of the dwelling site (settlement). The majority of the settlements in the area are of a square style but some coexist with rectangular-style settlements, which is noteworthy. The dwelling sites of the Neolithic age found in Asan Bay area are mostly located in a ridge of hilly areas, divided into gentle, low areas (20~50 meters above sea level) and relatively high areas (50~80 meters above the sea level). Although location strongly corresponded to the residents' subsistence and the technical levels within the culture, it likely was greatly affected by natural environment where they lived, as well. In examining radiocarbon dating results and the excavated artifacts, the settlements found in Asan Bay were determined to belong to the period II(3,500~3,000 B.C.) stated in the Relative Chronological table of Dwelling sites in the Neolithic age, written by the author. Said Dwelling sites are proven to have a close relationship with those found on the coast of Gyeonggi Province(京畿道) and in the Geum River(錦江) valley. This is deemed to be the result of expansion and interchange between Gyeonggi Province(京畿道) group and Geum River(錦江) valley group, who constituted the large settlements. Additionally, the Daecheon-ri type dwelling sites in the Geum River valley were verified to be the result of exchange, and spread to the Asan Bay area in the same era. Two forms of Dwelling sites coexisted dynamically in the Asan Bay area around 3,500 B.C. Such a phenomenon resulted primarily from the expansion of the dwelling site due to the introduction of primitive agriculture, as well as environmental (temperature), biological and social changes at those times.

• Korean Journal of Heritage: History & Science
• /
• v.40
• /
• pp.357-386
• /
• 2007

At present, thirteen Buddhist bells of Unified Silla are known to the world: Six in Korea, five in Japan and two other bells, and three out of them are impossible to make out its original form. Therefore, we divided the form of Unified Silla Buddhist bells based on the ten other bells, and we tried out to prove the manufacturing technology by the comparison of the research material of Uncheon-dong bell and existing research materials of other bells, in other to find their linkage based on the alloy elemental composition. We divided Unified Silla Buddhist bell into two types: Type I has symmetric apsaras and regular patterns on its face and it was made in early Silla period; type II has asymmetric apsaras and irregular pattern arrangement and made in late Silla period. In particular, Uncheon-dong Buddhist bells is very similar to Komyoji[光明寺] temple bell from ninth century in Japan. It is peculiar that the apsaras on Uncheon-dong bell play vertical music instruments that are never seen in Unified Silla Buddhist bell. Most of Unified Silla Buddhist bell are compounded with Cu-Sn or Cu-Sn-Pb system. From eighth and ninth century, bells were cast with even composition of copper, tin and lead, and the bronze alloy ratio was similar to the record in Gogonggi[考工記], Jurye[周禮], a book from ancient China. Particularly, Uncheon-dong bell is in a rare case of Cu-Sn-Pb-As system. As had been rarely used in Unified Silla Buddhist bells, so we presented the relative research materials. As has the same nature as Pb. Because As easily volatilize at high temperature, it is hard to use. But it has its merit of solidity and durability. Pb enhances fluidity and thereby expresses the patterns more distinct; As makes the bell stronger. The result of lead isotope ratio could not exactly reveal a concrete producing center. However, over the analysis of our samples, hereby we suggest Uncheon-dong bell was made of materials from just one ore deposit.

• Journal of the Korean Institute of Landscape Architecture
• /
• v.50 no.2
• /
• pp.1-22
• /
• 2022

The modification effects of street trees on outdoor thermal comfort in summertime according to tree planting types and road direction were analyzed using a computer simulation program, ENVI-met. With trees, the air temperature and wind speed decreased, and the relative humidity increased. In the case of mean radiant temperature (T_mrt) and human thermal sensation, physiological equivalent temperature (PET) and universal thermal climate index (UTCI), there was a decrease during the daytime. The greatest change among the meteorological factors by trees happened in Tmrt, and PET and UTCI showed similar patterns with T_mrt·The most effective tree planting type on thermal comfort modification was low tree height, wide tree crown, high leaf area index, and narrow planting interval (LWDN). T_mrt, PET and UTCI showed a large difference depending on shadow patterns of buildings and trees according to solar altitude and azimuth angles, and building locations. When the building shade areas increased, the thermal modification effect by trees decreased. In particular, results on the east and west sidewalks showed a large deviation over time. When applying the LWDN, the northwest, west and southwest sidewalks showed a significant reduction of 8.6-12.3℃ PET and 4.2-4.5℃ UTCI at 10:00, and the northeast, east and southeast sidewalks showed 8.1-11.8℃ PET and 4.4-5.0℃ UTCI at 16:00. On the other hand, when the least effective type (high tree height, narrow tree crown, low leaf area index, and wide planting interval) was applied, the maximum reduction was up to 1.8℃ PET and 0.9℃ UTCI on the eastern sidewalks, and up to 3.0℃ PET and 0.9℃ UTCI on the western ones. In addition, the difference in modification effects on T_mrt, PET and UTCI between the tree planting types was not significant when the tree effects were reduced by the effects of buildings. These results can be used as basic data to make the most appropriate street tree planting model for thermal comfort improvement in urban areas in summer.

• Korean Journal of Ecology and Environment
• /
• v.56 no.1
• /
• pp.57-69
• /
• 2023

The objectives of this study were to analyze the fish community structures and distribution characteristics of fisheries resources in the Osip Stream and Wangpi Stream, fishery resources protection areas. For the study, we conducted fish samplings four times in the two streams from April to October 2019. In Osip Stream and Wangpi Stream, we sampled 31 species and 29 species and the dominant species were Zacco platypus (28.6%) and Squalidus multimaculatus(41.7%), respectively. According to the life type of fish species, primary freshwater species were collected 18 species(58.1%) and 21 species(72.4%), and migration fishes were sampled 4 species (12.9%) and 6 species (20.7%) in Osip Stream and Wangpi Stream, respectively. Fisheries resources species showed high relative abundance in June, and the fish biomass was highest in October. As a results of comparing the previous studies with this study, both rivers showed high biodiversity and were found to maintain stable populations of fishes. According to analysis of tolerance guilds, the proportion of tolerant species, based on the number of individuals, was composed of 14.4% and 1.1% in Osip Stream and Wangpi Stream, respectively. This very low ratio of tolerant species confirmed that both streams have very good physiochemical environment conditions. From the above results, it was judged that the fishery resource protection areas of Osip Stream and Wangpi Stream have high ecological function and preservation value. For sustainable use and management of fishery resource protection areas of Osip Stream and Wangpi Stream, it is suggested that biological disturbance management, fish discharge projects considering environmental capacity, efforts to improve the habitat environment, and establishing a fishery resource protection areas management system were necessary as considerations.

• Journal of Global Scholars of Marketing Science
• /
• v.19 no.3
• /
• pp.5-16
• /
• 2009

Corporate social responsibility (CSR) activities have been shown to be potential factors that can improve corporate image and increase the ability of corporations to compete. However, most previous studies related to CSR activities investigated how these activities influence product and corporate evaluation, as well as corporate image. In addition, some researchers treated consumers' perceptions of corporate motives as moderator variables in evaluating the relationship between corporate social responsibilities and consumer response. However, motive-based theories have some weaknesses. Corporate social responsibility activities cause two motives(egoistic vs. altruistic) for consumers, but recently, Vlachos et al. (2008) argued that these motives should be segmented. Thus, it is possible to transform the original theory into a modified theory model (persuasion knowledge model, PKM). Vlachos et al. (2008) segmented corporate social responsibility motives into four types and compared the effects of these motives on customer loyalty. Prior studies have proved that CSR activities with positive motives have positive influences on customer loyalty. However, the psychological reasons underlying this finding have not been determined empirically. Thus, the objectives of this research are twofold. First, we attempt to determine why most customers favor companies that they feel have positive motives for their corporate social responsibility activities. Second, we attempt to measure the effects of consumers' reciprocity when society benefits from corporate social responsibility activities. The following research hypotheses are constructed. H1: Values-driven motives for corporate social responsibility activities have a positive influence on the perceived reciprocity. H2: Stakeholder-driven motives for corporate social responsibility activities have a negative influence on the perceived reciprocity. H3: Egoistic-driven motives for corporate social responsibility activities have a negative influence on perceived reciprocity. H4: Strategic-driven motives for corporate social responsibility activities have a negative influence on perceived reciprocity. H5: Perceived reciprocity for corporate social responsibility activities has a positive influence on consumer loyalty. A single company is selected as a research subject to understand how the motives behind corporate social responsibility influence consumers' perceived reciprocity and customer loyalty. A total sample of 200 respondents was selected for a pilot test. In addition, to ensure a consistent response, we ensured that the respondents were older than 20 years of age. The surveys of 172 respondents (males-82, females-90) were analyzed after 28 invalid questionnaires were excluded. Based on our cutoff criteria, the model fit the data reasonably well. Values-driven motives for corporate social responsibility activities had a positive effect on perceived reciprocity (t = 6.75, p < .001), supporting H1. Morales (2005) also found that consumers appreciate a company's social responsibility efforts and the benefits provided by these efforts to society. Stakeholder-driven motives for corporate social responsibility activities did not affect perceived reciprocity (t = -.049, p > .05). Thus, H2 was rejected. Egoistic-driven motives (t = .3.11, p < .05) and strategic-driven (t = -4.65, p < .05) motives had a negative influence on perceived reciprocity, supporting H3 and H4, respectively. Furthermore, perceived reciprocity had a positive influence on consumer loyalty (t = 4.24, p < .05), supporting H5. Thus, compared with the general public, undergraduate students appear to be more influenced by egoistic-driven motives. We draw the following conclusions from our research findings. First, value-driven attributions have a positive influence on perceived reciprocity. However, stakeholder-driven attributions have no significant effects on perceived reciprocity. Moreover, both egoistic-driven attributions and strategic-driven attributions have a negative influence on perceived reciprocity. Second, when corporate social responsibility activities align with consumers' reciprocity, the efforts directed towards social responsibility activities have a positive influence on customer loyalty. In this study, we examine whether the type of motivation affects consumer responses to CSR, and in particular, we evaluate how CSR motives can influence a key internal factor (perceived reciprocity) and behavioral consumer outcome (customer loyalty). We demonstrate that perceived reciprocity plays a mediating role in the relationship between CSR motivation and customer loyalty. Our study extends the research on consumer CSR-inferred motivations, positing them as a direct indicator of consumer responses. Furthermore, we convincingly identify perceived reciprocity as a sub-process mediating the effect of CSR attributions on customer loyalty. Future research investigating the ultimate behavior and financial impact of CSR should consider that the impacts of CSR also stem from perceived reciprocity. The results of this study also have important managerial implications. First, the central role that reciprocity plays indicates that managers should routinely measure how much their socially responsible actions create perceived reciprocity. Second, understanding how consumers' perceptions of CSR corporate motives relate to perceived reciprocity and customer loyalty can help managers to monitor and enhance these consumer outcomes through marketing initiatives and management of CSR-induced attribution processes. The results of this study will help corporations to understand the relative importance of the four different motivations types in influencing perceived reciprocity.

• Journal of The Korean Society of Grassland and Forage Science
• /
• v.29 no.3
• /
• pp.171-178
• /
• 2009

The study was conducted to clarify the mixed seeding rate of whole crop barley with hood type and forage pea for using of forage crops and to compare the forage yield and quality. At a mixed seeding rate between the whole crop barley (WCB) and forage pea, The heading date and plant height of WCB were not a difference according to mixed seeding rate of forage pea. The tillers of the WCB were a decrease and plant of the forage pea were a increase according to increased seeding rate of forage pea. The lodging index of the WCB was a appearance with distribution of $0{\sim}3$, The lodging index of WCB with a 20kg/10a seeding rate of a only WCB without seeding of the forage pea was 3. The overwintering rate of forage pea was a appearance more than 90% at all treatment. The plant height of forage pea was a increase according to increased seeding rate of forage pea at 14 kg/10a and 20 kg/10a plots of WCB. At a mixed seeding between the WCB and forage pea, The fresh weight was a increase according to increased seeding rate of forage pea and was a appearance more than 3,000 kg at all treatment plot. But the dry matter weight was decrease according to increased seeding rates of forage pea. The dry matter weight of 20 kg/10a seeding rate of a only WCB without seeding of the forage pea showed the most amount with 1,266 kg. The crude protein (CP) content was a tendency to increase according to increased seeding rates of forage pea. But, the relative feed value (RFV) was a tendency to decrease according to increased seeding rate of forage pea. The highest RFV was 183.8 at 14 kg/10a seeding rate of a only WCB without seeding of the forage pea. The acid detergent fiber (ADF) and neutral detergent fiber (NDF) were a increase according to increased seeding rate of forage pea at 14 kg/10a and 20 kg/10a plots of WCB. The highest content of ADF and NDF were 23.9% and 46.3% at mixed seeding rate of 20 kg/10a of WCB with 10 kg/10a of forage pea, respectively. The highest sum of standardized score by fresh weight, dry matter weight, CP, ADF, NDF and RFV was 2.309 at mixed seeding rate of 20 kg/10a of WCB with 7.5 kg/10a of forage pea. The optimum mixed seeding rate was a considered judgment in the order of mixed seeding rate of 20 kg/10a of WCB with 7.5 kg/10a of forage pea, mixed seeding rate of 20 kg/10a of WCB with 5.0 kg/10a of forage pea.

• Journal of Korean Society of Forest Science
• /
• v.33 no.1
• /
• pp.1-32
• /
• 1977

This study has been made to find out more effective way of vegetation establishment on severely denuded forest land from the viewpoint of soil moisture regimes. Various environmental factors were measured to estimate soil moisture conditions of different sites. Soil moisture influence on growth of over vegetations, water requirement and drought resistance were analyzed. The efficiency of water use was also reckoned at different fertility levels and different soil moisture conditions. This research is composed of field experiment and green house experiment. Field experiment includes height growth, survival and coverage analysis of cover vegetations (Robinia pseudoacacia L., Lespedeza bicolor Turcz, Arundinella hirta Tanaka var. ciliare Koidzumi.) with 4 fertility level treatments on 3 slopes (Steep: $37^{\circ}$, Moderate: $25^{\circ}$, Gentle; $17^{\circ}$) during dry season (1 April-30 June) and wet season (1 July-10 September). At the same time temperature, relative humidity and precipitation were measured to understand the environmental changes. Soil moisture conditions were measured with soil moisture meter with 24 soil cells. Green house experiment comprised height, fresh weight and dry weight measurements of cover vegetations with 4 fertility levels and 3 moisture conditions for 70 days. The results extracted from experiments are as follews. 1. Cover vegtations have 3 patterns of water requirement at the early stage of growth. a) Robinia type has high water requirement and weaker drought resistance. b) Lespedeza type has low water requirement and stronger drought resistance. c) Arundinella type has moderate water requirement and weaker drought resistance. 2. The vegetations have different optimum fertility levels in different soil moisture supply condition. a) Robinia needs a low fertility level in dry condition and a high level in wet condition. b) Lespedeza needs only low fertility level in all conditions. c) Arundinella needs a low fertility level in dry condition and a high level in wet condition. 3. The efficiency of water use (Water/1g dry weight) by fertility levels is different from one another. Robinia and Arundinella have a good efficiency at low fertility level in dry condition and at high fertility level in wet condition. Lespedeza has a good efficiency at low fertility level in all conditions. 4. $P_2O_5$ requirement of Robinia and Lespedeza is high, but that of Arundinella is low. Soil moisture condition has a great influence on $P_2O_5$ absorption in dendued forest land. Once Vegetations are established on suitable sites with optimum fertitity level according to different moisture condition, even the small amount of soil water in denuded land can he used with high efficiency and the effect of fertility treatment can be maximized.