• Journal of Plant Biotechnology
• /
• v.43 no.1
• /
• pp.104-109
• /
• 2016

Rosa rugosa is a medicinal, ornamental, and edible plant native to Eastern Asian countries, including Korea, Japan, and China. The aim of this study was to establish a system for biomass production and secondary metabolite accumulation during in vitro culture and acclimatization of Rosa rugosa. The highest rate of multiple shoot proliferation was achieved with $8.8{\mu}M$ benzyladenine (BA) (83.3%). However, the number of shoots (14.4 per explant) at $4.4{\mu}M$ BA was higher than that at $8.8{\mu}M$ BA. Compared to BA, a combination of thidiazuron (TDZ) and indole butyric acid (IBA) exhibited significantly lower shoot induction, with only 50.0~79.2% and 4.2~16.7% relative shoot formation, respectively. During acclimatization, shoots were sampled every week and their total phenolic contents were analyzed. Among various growth factors, fresh weight showed the most dramatic increase from the 3rd week (88.0 mg/plant) to 4th week (132.7 mg/plant). Total phenolics and flavonoids contents were the highest at $1^{st}$ week of acclimatization. Depending on developmental stages, total phenolics and flavonoids contents were higher in 1-yr-old shoots grown ex vitro than in those of older field-grown or in vitro-grown plants. Amongst different ages of field grown plants, 6-year-old plants, the oldest in this study, showed the lowest content in total phenolics.

• Journal of Plant Biotechnology
• /
• v.37 no.2
• /
• pp.228-235
• /
• 2010

The establishment of cell suspension culture and plant regeneration of the halophytic Leymus chinensis (Trin.) are described in this study for the first time. Callus induction solid medium containing Murashige and Shoog (MS) basic salt, $2.0\;mg\;l^{-1}$ 2,4-dichlorophenoxyacetic acid (2,4-D), and $5.0\;mg\;l^{-1}$ L-glutamic acid with $30.0\;g\;l^{-1}$ sucrose and $4.0\;g\;l^{-1}$ gelrite for solidification induced the highest rate of cell division in Type 1 callus among calli of various types. Liquid medium with the same hormone distribution was therefore, used for cell suspension culture from Type 1 callus. Over a 30 d suspension culture at 100 rpm, great amounts of biomass were accumulated, with 71.07% average daily increment and 22.32-fold total fresh weight increment. Comparison of before and after suspension culture, the distribution of different size callus pieces and the maintenance of callus type were basically unaltered, but a slight increase in relative water contents was observed. To induce the potential of plant regeneration, the directly transferring on plant regeneration solid medium containing MS basic salt, $0.2\;mg\;l^{-1}$ $\alpha$-naphthalene acetic acid (NAA), $2.0\;mg\;l^{-1}$ kinetin (Kn), and $2.0\;g\;l^{-1}$ casamino acid and indirectly transferring were simultaneously performed. Even now growth rates of suspension-derived callus on solid medium were approximately half of those of Type 1 callus, but faster somatic embryogenesis was observed. Rooting of all regenerated shoots was successfully performed on half-strength MS medium. All plants appeared phenotypically normal.

• Journal of Plant Biotechnology
• /
• v.43 no.3
• /
• pp.332-340
• /
• 2016

Seed size traits are controlled by multiple genes in crops and determine grain yield, quality and appearance. However, the molecular mechanisms controlling the size of plant seeds remain unclear. We performed functional analysis of BrPATL4 encoding Sec14-like protein to determine the genetic architecture of seed size, shape and their association analyses. We used 60 $T_3$ transgenic rice lines to evaluate seed length, seed width and seed height as seed size traits, and the ratios of these values as seed shape traits. Pleiotropic effects on general architecture included small seed size, erect panicles, decreased grain weight, reduced plant height and increased sterility, which are common to other mutants deficient in gibberellic acid (GA) biosynthesis. To test whether BrPATL4 overexpression is deleterious for GA signal transduction, we compared the relative expression of GA related gene and the growth rate of second leaf sheath supplied with exogenous $GA_3$. Overexpression of BrPATL4 did not affect GA biosynthesis or signaling pathway, with the same response shown under GA treatment compared to the wild type. However, the causal genes for the small seed phenotype (D1, SRS1, and SRS5) and the erection of panicles showed significantly decreased levels in mRNA accumulation compared to the wild type. These results suggest that the overexpression of BrPATL4 can control seed size through the suppression of those genes related to seed size regulation. Although the molecular function of BrPATL4 is not clear for small seed and erect panicles of BrPALT4 overexpression line, this study provides some clues about the genetic engineering of rice seed architecture.

• Korean Journal Plant Pathology
• /
• v.10 no.4
• /
• pp.261-269
• /
• 1994

One hundred and ninety two isolates of Armillaria were obtained from mycelial fans on infected hosts, rhizomorphs, and single basidiospores or trauma tissue of fruiting bodies. Mating tests showed that two of these isolates were A. mellea, eight were A. tabescens, 20 were A. ostoyae, and 162 were A. gallica. Armillaria ostoyae was mainly isolated from Pinus koraiensis and Qurecus spp., A. tabescens from fruiting bodies on Pinus densiflora and Qurecus spp., and A. gallica from many tree species but not Pinus koraiensis. Armillaria mellea, A. gallica, A. ostoyae and A. tabescens showed distinct protein banding patterns. Mycelial growth and rhizomorph formation was good on basal medium with ethanol added. A. gallica and A. mellea formed many rhizomorphs, but A. ostoyae did not. A. gallica showed the best rhizomorph formation on media with tannic acid and ethanol, but a. mellea formed the most rhizomorphs on gallic acid. Rhizomorphs showed monopodial branching for A. gallica and dichotomous branching for A. ostoyae. Fruiting bodies. formed in the laboratory on sawdust media most abundantly by A. tabescens. In nature, fruit body formation by A. tabescens was from early to mid August. A. ostoyae and A. gallica fruit bodies were formed from early August to late October. While there are common names in Korea for A. mellea and A. tabescens, such as mulberry mushroom relative, no common names are available for A. gallica and A. ostoyae. Therefore, we refer to a. gallica as the Gastrodia mushroom because it has been used to produce Gastrodia and A. ostoyae as the Korean pine mushroom because it is frequently found as mushrooms on Korean pine.

• Journal of the Korean Vacuum Society
• /
• v.12 no.2
• /
• pp.123-129
• /
• 2003

Thin transparent Cu films in the thickness range of 10 ~ 40 nm are deposited by rf-magnetron sputtering on porous silicon (PS) anodized on p-type silicon in dark. Microstructural features of the Cu films are investigated using SEM, AFM and XRD techniques. The RMS roughness of the Cu films is found to be around 1.47 nm and the grain growth is columnar with a (111) preferred orientation and follows the Volmer-Weber mode. The photoluminescence studies showed that a broad luminiscence peak of PS near the blue-green region gets blue shifted (~0.05 eV) with a small reduction in intensity and therefore, Cu-related PL quenching is absent. The FTIR absorption spectra on the PS/Cu structure revealed no major change of the native PS peaks but only a reduction in the relative intensity. The I-V characteristic curves further establish the Schottky nature of the diode with an ideality factor of 2.77 and a barrier height of 0.678 eV. An electroluminiscence (EL) signal of small intensity could be detected for the above diode.

• Journal of the Korean Vacuum Society
• /
• v.9 no.4
• /
• pp.400-405
• /
• 2000

We investigated the effect of TMIn (trimethly-indium) source depletion on InGaAs, InGaAsP and 1.55 $\mu\textrm{m}$ InGaAs/InGaAsP SMQW by using EPISON ultrasonic monitor for measuring the concentration of metalorganic/carrier gas mixtures. And the problems for the growth reproducibility in MOCVD was solved by using an EPISON ultrasonic monitor with closed-loop mode under the condition of TMIn source depletion. The saturation pressure of TMIn was dramatically decreased over consumption of 80%. In the case of bulk epilayer, Up-shifting of 300 arcsec to Ga-rich direction and FWHM broadening by a factor of two in DCXRD spectrum were observed due to the TMIn source depletion. In the case of SMQW, Up-shifting of 300 arcsec to Ga-rich direction in DCXRD spectrum and blue-shift of 40 nm in PL spectrum were observed due to the TMIn source depletion. However, good reproducibility ($\Delta\theta$<$\pm$100 arcsec) was achieved even the condition of 95% of TMIn consumption, when we used the EPISON with closed-loop mode.

• Journal of Fashion Business
• /
• v.21 no.5
• /
• pp.43-60
• /
• 2017

The purpose of this study is to conduct an in-depth examination into the cause of stress as well as reasons for turnover relative to fashion industry workers in their 20s-30s, thereby seeking effective improvement methods to reduce turnover. The study method consisted of one-on-one in-depth interviews to collect data on 15 fashion industry workers. Results were as follow. First, causes of stress for fashion industry workers in their 20s-30s include work related factors, interpersonal relations, and organizational culture, while the most frequently mentioned reasons for turnover were concerns about career track and aptitude as well as annual salary, revealing that self-improvement related growth potential is the most significant factor for turnover. Second, it was not one stress factor that influenced turnover but a composite of several stress factors that motivated individuals to change jobs. Last, time flexibility, self-esteem, and development potential were critical factors for turnover. Self-esteem and development potential that provide a sense of acknowledgment were especially emphasized as the most significant, revealing that the younger generation considers personal happiness to be critical and the more this aspect is not treated adequately the more the odds of choosing turnover. To mitigate this issue, an in-house educational system for self-development and an assignment rotation system must be adopted for workers to change to positions that fit their aptitude.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2000.02a
• /
• pp.68-68
• /
• 2000

펄스레이저 증착법(이하 PLD)을 이용하여 마이크로파 유전체 소자 및 절연 산화막으로의 응용을 위한 MgTiO3 박막을 다양한 기판상에서 증착하였다. 사파이어 기판에 (a,c-plane Al2O3) 성장된 MgTiO3 박막은 에피텍셜 성장(epitaxial growth)이 되었으며, SiO2/Si 및 Pt/Ti/Si 기판위세 성장된 MgTiO3 박막의 경우 003방향으로 배향(oriented) 되었다. MgTiO3 박막은 450~75$0^{\circ}C$까지 기판온도를 변화시키면서 증착시켰으며, 증착시 산소분압은 50~200 mTorr로 변화시켰다. PLD 증착시 타켓에 조사된 레이저 에너지 밀도는 약 2J/cm2였으며, MgTiO3 박막 증착후 200Torr O2 분위기에서 상온까지 1$0^{\circ}C$/min 의 속도로 냉각시켰다. 사파이어 c-plane 상에서 일머나잇(ilminite) MgTiO3 구조가 55$0^{\circ}C$ 에피텍셜 성장하는 것을 관찰할 수 있었으며, 사파이어 a-plane 상에서는 MgTiO3 구조가 $650^{\circ}C$ 이상부터 110방향으로 배향되며 성장하였다. $600^{\circ}C$ 이상에서 c-축으로 배향된 구조를 갖고 있었다. 증착된 MgTiO3 박막의 조성분석(stoichio metric analysis)을 위해 RBS 분석을 수행하여, 증착에 이용된 타켓과 동일한 조성을 갖는 MgTiO3 박막이 성장된 것을 확인할 수 있었다. 사파이어 기판상에 증착된 MgTiO3 박막은 가시영역에서 투명하였으며, 약 270nm 파장을 갖는 영역에서 급격한 흡수단을 보였다. 이때의 MgTiO3 박막은 AFM 분석을 통해 약 0.87mn rms roughness 값을 갖는 매우 평탄한 표면구조를 갖고 있는 것을 확인하였다. MIM(Pt/MgTiO3/Pt) 구조의 캐패시터를 형성시켜 MgTiO3 박막의 유전특성(dielectric properties)을 관찰하였다. PLD로 성장된 MgTiO3 박막의 유전율(relative dielectric constant)은 약 22였으며, 1MHz에서 약 1.5%의 유전손실(dielectirc loss) 값을 보였다. 또한 이때 MgTiO3 박막은 낮은 유전분산값을 보였다.

• The Plant Pathology Journal
• /
• v.29 no.2
• /
• pp.144-153
• /
• 2013

Diverse bacteria are known to colonize plants. However, only a small fraction of that diversity has been evaluated for their biopesticide potential. To date, the criteria for sampling and selection in such bioprospecting endeavors have not been systematically evaluated in terms of the relative amount of diversity they provide for analysis. The present study aimed to enhance the success of bioprospecting efforts by increasing the diversity while removing the genotypic redundancy often present in large collections of bacteria. We developed a multivariate sampling and marker-based selection strategy that significantly increase the diversity of bacteria recovered from plants. In doing so, we quantified the effects of varying sampling intensity, media composition, incubation conditions, plant species, and soil source on the diversity of recovered isolates. Subsequent sequencing and high-throughput phenotypic analyses of a small fraction of the collected isolates revealed that this approach led to the recovery of over a dozen rare and, to date, poorly characterized genera of plant-associated bacteria with significant biopesticide activities. Overall, the sampling and selection approach described led to an approximately 5-fold improvement in efficiency and the recovery of several novel strains of bacteria with significant biopesticide potential.

• Research in Plant Disease
• /
• v.22 no.3
• /
• pp.133-144
• /
• 2016

Powdery mildew (Podosphaera xanthii) causes severe damage to pumpkin crops grown in open fields and plastic house. Initially, we used ten accessions of pumpkin species; Cucurbita pepo (3), C. maxima (2), C. moschata (2), and C. argyrosperma (3) to study the disease progress in different stages of seedling development. Commercial pumpkin varieties were used as susceptible host for inoculum management and young seedlings were inoculated by dusting powdery mildew spores on the cotyledons, 1-true-leaf and 2-true-leaf seedling stages. Based on initial study, we further evaluated 218 pumpkinaccessions for their resistance to powdery mildew in different seedling stages under plastic house. Area under disease progress curve (AUDPC) and relative AUDPC (rAUDPC) was higher in cotyledonary and 1-true-leaf than 2-true-leaf stage. Seedlings at cotyledons and 1-true-leaf seedling stage displayed more susceptibility to powdery mildew. Based on evaluation of 2-true-leaf stage, IT 110859 and IT 278459 from C. pepo and C. argyrosperma identified as resistant (<0.2). Of the 228 pumpkin accessions, 21 (9.2%) pumpkin accessions consisting of C. pepo (2), C. maxima (5), C. moschata (13), and C. argyrosperma (1) exhibited intermediate resistance (<0.4) to powdery mildew and these accessions are useful to growers for its rational management.