• 설비공학논문집
• /
• 제14권11호
• /
• pp.907-913
• /
• 2002

An experimental study on energy density distributions produced by dish solar concentrating system was performed to optimally design and rightly position a cavity receiver. This deemed also very useful to find and correct various errors associated with a concentrator. It is observed that the actual focal length is 2.17 m with a maximum energy density of 1.89 MW/$m^2$. By evaluating the position of flux centroid, it was found that there are errors within 2 cm from the target center. As a result of the percent power within radius, approximately 90% of the incident radiation is intercepted by about 0.06 m radius. The area concentration ratio normalized to 800 W/$m^2$ insolation and 90% mirror reflectivity was 347 suns. The total integrated power of 2467 W was measured under focal flux distributions, which corresponds to the intercept rate of 85.8%.

• 한국세라믹학회지
• /
• 제43권10호
• /
• pp.613-618
• /
• 2006

Graphite is suitable materials as a moderator, reflector, and supporter of a nuclear reactor because of high tolerance to the high temperature and neutron irradiations. Because graphite is so weak to the oxidation, its oxidation study is essentially demanded for the operation and design of the nuclear reactor. This work focuses on the effect of the surface oxidation of graphite according to the surface treatment. With thermogravimeter (TG), oxidation characteristics of the isotropic graphite are measured at the three temperature areas, and oxidation ratio and amounts are estimated as changing the surface roughness. Furthermore, the polished graphite surface produced fom the surface treatment is investigated with the Raman spectroscopic study. Oxidation behaviors of the surface are also evaluated as elimination the polished layer by washing with strong sonication.

• 한국조명전기설비학회:학술대회논문집
• /
• 한국조명전기설비학회 2003년도 학술대회논문집
• /
• pp.19-23
• /
• 2003

헤드램프는 안개등, 후미등, 제동등, 방향지시등과 함께 자동차의 등화장치 중의 하나로써 특히 야간의 안전운행을 위해 필수적인 장치이다. 야간 운전시 차량의 운전자는 마주오는 차량의 헤드램프에 의한 눈부심으로 도로의 사정을 정확히 파악할 수 없는 일이 종종 발생하게 되는데 이것은 야간 사고의 큰 원인으로 지목된다. 그러므로 헤드램프의 빔패턴은 정확하고 sharp한 cut-off line을 가져야 한다. 본 논문에서는 미국식 빔패턴(SAE type)을 고려한 헤드램프용 반사갓 설계의 한가지 알고리즘을 제시한다.

• 한국정보통신학회:학술대회논문집
• /
• 한국해양정보통신학회 2006년도 춘계종합학술대회
• /
• pp.603-606
• /
• 2006

본 연구에서는 기존의 Log-Periodic Tooth 안테나의 이득 향상에 대한 연구를 하였다. 밀리미터파 대역용 PMMW(Passive Millimeter Wave) 이미지 센서에 적합한 고이득, 광대역, 평판구조 특성을 가지는 반사판이 추가된 형태의 Log-Periodic Tooth 안테나 구조를 제안한다.

• 태양에너지
• /
• 제7권1호
• /
• pp.3-13
• /
• 1987

A batch type passive solar water systems, which perform the dual function of absorbing the solar energy and storing the heated water, have been designed and fabricated for the purpose of side-by-side testing at KIER. The test models included an A, B and C type batch systems which were classified according to the design of box and arrangement of tanks. The year-round performance tests show that B type batch system taken the step-wise tank arrangement indicates 55.7% yearly-average collection efficiency factor and 61% yearly-average maximum collection efficiency factor. Computer-aided-experimental results show that the sufficient hot water can be obtained in the early morning if the glazing is supplemented by a reflector/insulation cover. The thermal performance equation has been developed for the prediction of hourly variation of the water temperature in tank.

• Nuclear Engineering and Technology
• /
• 제54권12호
• /
• pp.4393-4411
• /
• 2022

In recent years, beryllium oxide has been widely utilized in multiple compact nuclear reactors as the neutron moderator, the neutron reflector or the matrix material with dispersed nuclear fuels due to its prominent properties. In the past 70 years, beryllium oxide has been studied extensively, but rarely been systematically organized. This article provides a systematic review of the application history, thermal properties, mechanical properties, corrosion behavior and fabrication methods of beryllium oxide. Data from previous literature are extracted and sorted out, and all of these original data are attached as the supplementary material, so that subsequent researchers can utilize this paper as a database for beryllium oxide research in reactor design or simulation analysis, etc. In addition, this review article also attempts to point out the insufficiency of research on beryllium oxide, and the possible key research areas about beryllium oxide in the future.

• 한국인터넷방송통신학회논문지
• /
• 제11권3호
• /
• pp.9-15
• /
• 2011

리플렉트어레이 안테나는 반사경 안테나의 단점을 보완하여 대체할 새로운 형태의 안테나로 대두되고 있다. 하지만 반사판이 단층구조일 경우 대역폭이 매우 좁다는 단점이 있고, 대역폭을 넓히기 위하여 다층구조의 반사판을 사용할 경우 설계가 어렵고 제작 단가가 높아지게 된다. 본 논문에서는 이러한 단점들을 극복하기 위하여 단층구조를 사용하여 제작 단가를 낮추면서 협대역 특성을 극복할 수 있는 정사각형에 U자 모양 슬롯을 낸 패치를 이용하여 리플렉트어레이 안테나를 설계하였다. 제안된 리플렉트어레이 안테나는 12.5 GHz에서 55.5 %의 효율과 14 % 이상의 1 dB gain bandwidth 특성을 갖는다.

• Journal of Magnetics
• /
• 제21권3호
• /
• pp.450-459
• /
• 2016

Experimental results and data of numerical simulations are presented, concerning generation of wideband radio frequency (RF) oscillations in a nonlinear transmission line (NLTL) which contains a pre-magnetized core of ferrite material. Emphasis is made on the means for extracting the RF signal from the line, in order to radiate it into free space. Antennas of two types that can be used for the purpose are considered, both featuring a coaxial design. This permits availing of the principal advantages of coaxial systems, such as operation in the mode of a traveling TEM wave; wide range of the transmitted frequencies, and a reasonably simple design. The antennas studied, specifically a disc-cone dipole (DCD) and an impulse reflector antenna ('Half-IRA', or HIRA type) differ significantly in effective width of the radiated spectrum and in spatial characteristics of the radiated field in far region.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2004년도 추계학술대회 논문집
• /
• pp.818-821
• /
• 2004

With a rapid development in the area of micro and ultra precision technology, the micro surface machining of small size parts are explosively increased. Especially, to improve efficiency of various beams in lens and reflector, non-rotational symmetric form and several mm level heights changeable surface can be machined at a time. These geometric complex 3D surface cannot be machined by general short stroke FTS. The long stroke FTS if firmly needed to move directly several mm and have nm level positioning accuracy for the complex surface form. The long stroke FTS used linear motors to drive moving unit long and fine, aero static bearings to decrease friction and moving errors in guide way, optical linear scale with nm level resolution to measure position of FTS. Furthermore, to increase the performance of acceleration of FTS, the light material, such as AL is used for the structure and the high stiffness box type structure is selected. In this paper, the genetic algorithm approach is described to determine a set of design parameters for auto tuning. The authors have attempted to model the design problem with the objective of minimizing the error, such as variable pattern change. This method can give the better alternative than existing other method.

• 한국위성정보통신학회논문지
• /
• 제10권1호
• /
• pp.77-82
• /
• 2015

본 논문에서는 LED 형광등에 활용이 가능한 컨버터 관한 연구를 수행하였다. 기존 고효율에너지 기자재로 지정된 형광램프용 고조도 반사갓이 LED 형광램프의 Heat-sink 구조상 활용할 수 없는 구조이기 때문에 LED 형광램프 컨버터의 에너지 효율이 뛰어난 회로 설계 및 보호회로 설계가 필요하다. 따라서 본 논문에서는 직관형 LED램프 컨버터에 회로구동방식을 적용한 LED 형광등 연구를 수행하였다. 또한, LED를 광원으로 한 'LED 램프'와 일반 상용 전원에 접속해 직류 전원을 공급할 수 있는 컨버터에 대하여 설계 및 제작을 하였다.