• Journal of Animal Environmental Science
• /
• v.16 no.2
• /
• pp.123-128
• /
• 2010

It is investigated the development of swine liquid manure spreading system for a polyethylene film (PE vinyl) based greenhouse used for planting vegetables. These types of vinylhouses are normally six to eight meters wide; the spread system must be contained and capable of operating within this area. The system we designed for use here consisted of the following parts: 1) a reel for loading the hose, 2) hydraulic motor and cylinder to generate hydraulic pressure, 3) discharge unit, and 4) a frame with a 3-point hiteh link to the tractor. With this system, there are two types of hoses that can be used, a flexible flat hose that can be mounted directly to a tractor or a solid firm round hose which usually separated from the tractor. In either case, the discharge unit remains on the tractor. It is found that by using our spread system overall efficiency was 5 times greater than spreading swine liquid manure manually.

• Clinics in Orthopedic Surgery
• /
• v.10 no.4
• /
• pp.468-478
• /
• 2018

Background: The restriction of wrist motion results in limited hand function, and the evaluation of the range of wrist motion is related to the evaluation of wrist function. To analyze and compare the wrist motion during four selected tasks, we developed a new desktop motion analysis system using the motion controller for a home video game console. Methods: Eighteen healthy, right-handed subjects performed 15 trials of selective tasks (dart throwing, hammering, circumduction, and winding thread on a reel) with both wrists. The signals of light-emitting diode markers attached to the hand and forearm were detected by the optic receptor in the motion controller. We compared the results between both wrists and between motions with similar motion paths. Results: The parameters (range of motion, offset, coupling, and orientations of the oblique plane) for wrist motion were not significantly different between both wrists, except for radioulnar deviation for hammering and the orientation for thread winding. In each wrist, the ranges for hammering were larger than those for dart throwing. The offsets and the orientations of the oblique plane were not significantly different between circumduction and thread winding. Conclusions: The results for the parameters of dart throwing, hammering, and circumduction of our motion analysis system using the motion controller were considerably similar to those of the previous studies with three-dimensional reconstruction with computed tomography, electrogoniometer, and motion capture system. Therefore, our system may be a cost-effective and simple method for wrist motion analysis.

• Proceedings of the Korean Society for Agricultural Machinery Conference
• /
• 2000.11b
• /
• pp.287-294
• /
• 2000

Calculation of the flexural rigidity value (EI) is indispensable for prescription of deflection characteristics of crop stalks in harvesting□Conventionally□EI has been determined by either average EI of the whole stalk or average EI of each stems divided into node through the calculation method of cantilever with homogeneous section□However□deflection characteristics of crop stalks caused by mechanical operation such as combine harvester were not exactly presumed by these conventional EI through the experiment by authors. Further, actual EI of a stalk changes in company with a change of moisture contents as time passes during the experiment. Finally, efficient calculation method for determining EI is needed in order to improve these problems. In this study, mechanical model based on actual structure of the crop stalk with variety sectional area was proposed. This mechanical model is calculated by the theory of cantilever with continuous stages. Therefore, improvement of both calculating accuracy on EI and efficiency of measuring system was tried. At first, this calculation method was applied to piano wire of which EI was recognized in advance. As a result, EI calculated from this new method coincided approximately with piano wire's EI. Next, applying to crop stalks as same as piano wire, relationship between loads acting on crop stalks and deflection values calculated by EI using this new calculation method was exactly presumed in comparison with conventional method. Further, measuring time of deflection test was greatly reduced. Finally, new calculation method of EI will be available for estimating mechanical characteristics of so many kinds of crop stalks in harvesting operation. Further, in this study, new deflection test using image-processing apparatus by computer will be introduced.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.50 no.3
• /
• pp.326-333
• /
• 2014

This study was conducted to investigate the fishing efficiency of an improved LED fishing lamp for squids. A total of 31 fishing operations were carried out with six-crew commercial fishing vessel Haengbok-Ho (24 tons) on which 43.2kW LED was installed, along with 14 automatic jigging machines, from October 6 to November 16, 2012. The 19 fishing vessels with Haengbok-Ho were compared with a control subject was 24 tons or 29 tons. A total illuminating power of metal halide (MH) fishing lamps in the control fishing vessel was either 84kW or 120kW. The number of automatic jigging machines in the control vessels was 8-18 and the number of crews engaged for fishing operation was 3-13. Average fuel consumption of LED fishing vessels during fishing operation was 505.1l which led to an average fuel consumption of 42.7l per hour. LED fishing vessel and MH fishing vessel caught on an average 1,946 squids and 2,439 squids, respectively, during the study period. Crews (hand line and hand reel) caught about 2.2 times the automatic jigging machines for LED fishing vessel and about 2.1 times for MH fishing vessel. Meanwhile, catches by the fishing vessels with LED in the combined total number per one line of automatic jigging machine and per crew were 86.6% of that of the control fishing vessel with MH. Also, fishing vessels with LED per automatic jigging machine achieved 71.8% of catches of that with MH fishing lamp. The catches of squids per the fishing vessel with 1W LED fishing lamp were higher by more than 135.5% of that in the fishing vessel with MH, which showed a good fishing performance even with only the use of a LED fishing lamp.

• Journal of Sericultural and Entomological Science
• /
• no.12
• /
• pp.21-36
• /
• 1970

This studies have been carried out to 3nd various causes of cleanness defects on raw silk which has been increased since 1967 in Korea, so that this treatise may be a guide inform action to improve such a defect in future. The cocoon treatment for the proposed work was carried starting with in worst condition to find the critical limit of degrading through such a work. And various analysis have been also worked out using the annual silk testing data past a few years. The results obtained are as follows. 1. There was a great relationship between cleanness and neatness result. 2. Cleanness result is greatly influenced by mounting conditions and handling of cocoons, which brought 40 percent lower as cleanness result than standard ones in which caused minor defects, especially loops and split ends, so the bad mounting conditions and handling of fresh cocoons degraded raw silk from 4A grade to E. 3. The use of good water quality brought the difference of 1.04 percent in cleanness result rather than the use of bad one. 4. Well technical work brought the difference of 0.86 percent in cleanness result rather than poor technical work. 5, Satisfactory cocoon drying installation brought the difference of 1.97 percent in cleanness result rather than insufficient one. 6. Automatic reeling machine marked lower 1,55 percent in cleanness result than multi-end reeling machine. 7. The degrading of cleanness result from 1965 year silk to 1969 year silk marked 1.99 percent, which almost responds to the degrading rate from good to poor cocoon drying installed cleanness results. In view of this result, nowadays, insufficient cocoon drying installation may be main factor to be worse cleanness result of Korean raw silk. 8. The factors of cleanness defect in raw silk once supplied with cocoon into factory are water quality, technique evaluation, cocoon drying capacity and s： reeling machine. The relationship between cleanness result and above factors are as follows. cleanness result＝neatness result＋1.6－1.04(1－a)－1.97(1－b)－0.86(1-c)＋1.55${\times}$d a： The successive we ratio of water quality (0\longrightarrowl) b： The successive ratio of satisfactory cocoon drying installation (0\longrightarrowl) c： The successive ratio of well technical work (0\longrightarrowl) d： 1 in case multi-end reeling machine o in case automatic reeling machine 9, It is not admitted that there is heavy relationship between cleanness occurrence and nonbreaking reel ability. That mal$.$ be sowed with silk reeling technique. 10. The bad mounting conditions caused the worse result on the cocoon quality as much as cleanness. 11. Besides mounting conditions, there may be another factors affecting on the low reel ability of cocoons in Korea.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.27 no.4C
• /
• pp.295-307
• /
• 2002

The IEEE 1394 protocol is a de facto standard in multimedia digital home network. It supports several advanced features such as hot plugging, dynamic network reconfiguration, isochronous transmission and so on. Since the IEEE 1394 was adapted in the field of multimedia service with QoS guarantee, back bone network protocol with reel-time digital instrumentation and control sub networks, and physical layer protocol for real-time middleware such as real-time CORBA, the additional real-time features has been required in device driver implementation because of the necessity of the predictability enhancement. To guarantee the real-time features, the device driver of the IEEE 1394 should support the priority based packet processing and also need a isochronous buffer management mechanism to deal with the periodic isochronous communication. In this paper, we proposed a new software architecture of the IEEE 1394 device driver for supporting the real-time characteristics such as priority based packet processing, priority based scheduling and so on.

• Steel and Composite Structures
• /
• v.44 no.2
• /
• pp.199-210
• /
• 2022

This study build finite element analysis (FEA) models describing the bending events of coiled tubing (CT) at the wellhead and trips into the hole, accurately provide the state of stress and strain while the CT is in service. The bending moment and axial force history curves are used as loads and boundary conditions in the diametrical growth models to ensure consistency with the actual working conditions in field operations. The simulation diametrical growth results in this study are more accurate and reasonable. Analysis the factors influencing fatigue and diametrical growth shows that the internal pressure has a first-order influence on fatigue, followed by the radius of the guide arch, reel and the CT diameter. As the number of trip cycles increase, fatigue damage, residual stress and strain cumulatively increase, until CT failure occurs. Significant residual stresses remain in the CT cross-section, and the CT exhibits a residual curvature, the initial residual bending configuration of CT under wellbore constraints, after running into the hole, is sinusoidal. The residual stresses and residual bending configuration significantly decrease the buckling load, making the buckling and buckling release of CT in the downhole an elastic-plastic process, exacerbating the helical lockup. The conclusions drawn in this study will improve CT models and contribute to the operational and economic success of CT services.

• Progress in Superconductivity and Cryogenics
• /
• v.6 no.3
• /
• pp.21-26
• /
• 2004

Deposition condition of YBa$_2$Cu$_3$$O_{7-x}$ (YBCO) films on moving IBAD templates (CeO$_2$/IBAD-YSZ/SS) was studied in a hot-wall type metal organic chemical vapor deposition (MOCVD) process using single liquid source. The reel velocity was 40 cm/hr and the source mole ratios of Y(tmhd)$_3$:Ba(tmhd)$_2$:Cu(tmhd)$_2$ were 1:2.3:3.1 and 1:2.1:2,9, Two different types of IBAD templates with thin CeO$_2$ and thick CeO$_2$ layers were used, The YBCO films were successfully deposited at the deposition temperatures of 780~89$0^{\circ}C$ ; the a-axis growth was observed together with the c-axis growth up to 83$0^{\circ}C$. while the c-axis growth became dominant above 83$0^{\circ}C$. The top surface of the c-axis film was fairly dense and included a small amount of the a-axis growth, although the peaks of the a-axis grains were not observed in XRD pattern, The YBCO film deposited on IBAD template with thin CeO$_2$ layer showed low critical current of 2.5 A/cm-width. while the YBCO film deposited on IBAD template with thick CeO$_2$ layer showed higher critical current of 50 A/cm-width. This result indicates that thick CeO$_2$ layer is thermally more stable than thin CeO$_2$ layer at the high deposition temperature of the MOCVD process.s.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.32 no.5A
• /
• pp.451-459
• /
• 2007

RFID it reads information which is it writes, the semiconductor chip for and the radio frequency system which uses the hazard antenna it has built-in transmission of information it talks. Formation which is transmitted like this collection and America which it filtrates wey the RFID search service back to inform the location of the server which has commodity information which relates with an object past record server. The hazard where measurement analysis result the leader for electronic interference does not occur consequently together from with verification test the power level which is received from the antenna grade where it stands must maintain minimum -55dBm and the electronic interference will not occur with the fact that, antenna and reel his recognition distance the maximum 7m until the recognition which is possible but smooth hazard it must stand and and with the fact that it will do from within and and and 3-4m it must be used Jig it is thought.

• Journal of the Institute of Electronics Engineers of Korea CI
• /
• v.44 no.3
• /
• pp.23-30
• /
• 2007

RFID it reads information which is it writes, the semiconductor chip for and the radio frequency system which uses the hazard antenna it has built-in transmission of information it talks. Formation which is transmitted like this collection and America which it filtrates wey the RFID search service back to inform the location of the server which has commodity information which relates with an object past record server. The hazard where measurement analysis result the leader for electronic interference does not occur consequently together from with verification test the power level which is received from the antenna grade where it stands must maintain minimum -55dBm and the electronic interference will not occur with the fact that, antenna and reel his recognition distance the maximum 7m until the recognition which is possible but smooth hazard it must stand and and with the fact that it will do from within and and and 3-4m it must be used Jig it is thought.