• Journal of the Korean Wood Science and Technology
• /
• v.46 no.1
• /
• pp.100-106
• /
• 2018

This study was fulfilled to investigate the anatomical characteristics according to provinces. In order to compare anatomical characteristics between provinces we selected Goseong, Hongcheon, and Bonghwa as experimental sites. To use the tree rings formed at the same years we dated all tree rings by cross-dating method used in dendrochronology and the cutting years were successfully dated in 2014, 2012, and 2014 for woods from Goseong, Hongchen, and Bonghwa, respectively. Based on the cutting years tracheid lengths and widths were measured considering juvenile wood (tree rings between the pith and first 10 years), heartwood (tree rings formed between 1955 and 1964), and sapwood (tree rings formed between 2002 and 2011). According to the results about differences between tracheid lengths from three provinces, juvenile wood did not show a difference, statistically, but heartwood and sapwood showed differences as the tracheid lengths following Bonghwa, Hongcheon, and Goseong. Bongwha also showed the largest value in the trachied width among three provinces. The tracheid lengths in the radial direction increased up to around the first 20 years, and then they showed stabilized. All wood samples showed typical Korean red pine's characteristics in anatomical observation under a light microscope.

• Journal of the Korean Wood Science and Technology
• /
• v.43 no.4
• /
• pp.478-485
• /
• 2015

The aim of this study is to analyze the combustion and thermal properties in order to establish baseline data for the fire safety evaluation of domestic timbers. The combustion properties such as heat release rate, total heat release, gas yield, and mass loss were analyzed by the method of cone calorimeter test and thermogravimetry (TGA). Thermal decomposition temperatures of the specimens by TGA were recorded as $359.83^{\circ}C$ for White pine, $359.80^{\circ}C$ for Red-Leaved Hornbeam, $363.14^{\circ}C$ for Carolina poplar, $358.59^{\circ}C$ for Konara oak, and $362.11^{\circ}C$ Sargent cherry. Red-Leaved Hornbeam showed the highest value of heat release rate, but, Carolina poplar wood showed the lowest value. In case of the total heat release, Red-Leaved Hornbeam wood showed the highest value and Carolina poplar wood showed the lowest one. The gas analysis results showed that Sargent cherry wood had the lowest value of 0.021, and Konara oak had the highest at 0.031 in the $CO/CO_2$. The minimum value of mass reduction was recorded as 87.57% for Sargent cherry, but, on the other hand, it was 95.03% for Konara oak. There was a correlation between the gas generation of CO and $CO_2$, and combustion behavior of woods. These results are expected to be usful for providing a fundamental guideline with the fire safety of wood use in interior applications.

• Journal of the Korean Wood Science and Technology
• /
• v.43 no.4
• /
• pp.411-420
• /
• 2015

Despite of the same species there is a difference in the tree shape and its wood property due to quantitatiVe and qualitatiVe differences in wood cells by the intra-annual cambial actiVity. The purpose of this study was to proVide the fundamental database of intra-annual cambial seasonal actiVity for red pine in Sokwang-ri and Anmyondo for the determination of their wood qualities. As the results of intra-annual cambial actiVity, the initiation of cambial actiVity of red pine in the plots with Age Class V in Sokwang-ri was in the middle of April and it was at the beginning of April in all plots in Anmyondo. Only the plots with Age Class IX in Sokwang-ri showed relatiVely late initiation of cambial actiVity as between middle of May and middle of June. Except one plot with Age Class IX in Sokwang-ri all plots in both sites showed the same cessation of cambial actiVity as between middle and end of October. According to intra-annual cambial actiVity, the duration of cambial actiVity in Sokwang-ri is shorter than that of Anmyondo. On the other hand, the number of cell diVision of cambial actiVity in Sokwang-ri was more than those of Anmyondo. We could establish the database for intra-annual cambial actiVity for Sokwang-ri and Anmyondo to estimate their wood quality.

• Journal of the Korean Wood Science and Technology
• /
• v.37 no.1
• /
• pp.37-47
• /
• 2009

For the inspection of wood, machine vision is the most common automated inspection method used at present. It is required to sort wood products by grade and to locate surface defects prior to cut-up. Many different sensing methods have been applied to inspection of wood including optical, ultrasonic, X-ray sensing in the wood industry. Nowadays the scanning system mainly employs CCD line-scan camera to meet the needs of accurate detection of lumber defects and real-time image processing. But this system needs exact feeding system and low deviation of lumber thickness. In this study low cost CCD area sensor was used for the development of image processing system for lumber being fed. When domestic red pine being fed on the conveyer belt, lumber images of irregular term of captured area were acquired because belt conveyor slipped between belt and roller. To overcome incorrect image merging by the unstable feeding speed of belt conveyor, it was applied template matching algorithm which was a measure of the similarity between the pattern of current image and the next one. Feeding the lumber over 13.8 m/min, general area sensor generates unreadable image pattern by the motion blur. The red channel of RGB filter showed a good performance for removing background of the green conveyor belt from merged image. Threshold value reduction method that was a image-based thresholding algorithm performed well for knot detection.

• Journal of the Korean Wood Science and Technology
• /
• v.36 no.3
• /
• pp.93-100
• /
• 2008

For investigation of adsoption properties of cadmium elimination by wood charcoal, $25m{\ell}$ aqueous cadmium solutions in various concentrations were treated with 0.2 g wood charcoal of Red Oak (Quercus mongolica) for 280 minutes. Almost 100% of cadmium elimination ratio was obtained in the solutions with initial concentration of 20 and 40 ppm in the treatment, whereas they were 75 and 50% in those of 80 and 160 ppm. In the effect of treatment time, the highest amount of cadmium ions was eliminated during the first ten minutes in each solution so that the elimination ratio of each case was over 70% of the maximum elimination value. From the analysis of adsorptive cadmium adsorption mechanism using the Langmuir adsorption isotherm, it was suggested that cadmium ion molecules were adsorbed at the active sites on the charcoal particle in form of one layer. The Gibbs free energy of the adsorption process was calculated in negative value for each solution. This means the adsorption processes are spontaneous which do not require the extra input energy.

• Journal of the Korean Wood Science and Technology
• /
• v.46 no.6
• /
• pp.681-691
• /
• 2018

The typical methods of mercury intrusion porosimetry (MIP) and capillary flow porometry (CFP) were used to evaluate the pore size of cross-section of wood and the effect of the pore structure on the permeability of wood was analyzed in this study. The results of this study were as followings: The pore size of wood measured by CFP was larger than that measured by MIP except for Lime tree, Korean red pine and Paulownia. Among the three pore types of porous materials defined by IUPAC (through pores, blind pores, and closed pores), only through pores are related to permit fluid flow. MIP measures the pore size of both through pores and blind pores, while CFP measures the pore size of only constricted through pores. Therefore, pore size measured by MIP was not related to gas permeability, however pore size measured by CFP had a proportional relationship with gas permeability.

• Journal of the Korea Furniture Society
• /
• v.22 no.4
• /
• pp.299-307
• /
• 2011

This article aimed to provide objective and practical information on wood terms of making furniture focusing on the wood species that furniture designers and firms in Korea have used to create furniture from the traditional up to the modern times. Through the content analysis method with wood information from literature related to furniture at home and abroad, studios of making the traditional Korean furniture, domestic furniture firms, and the catalogues of Korean crafts council and Korea furniture society, the wood species of making furniture was studied in the terms showing the number of the species classified in needle leaf tree and broad leaf tree. As a result, the furniture wood terms were analyzed about 230 species including 200 broad leaf tree and 30 needle leaf tree. 74 out of 100 domestic species studied have been used from the traditional up to the modern time for creating the traditional Korean wood furniture. The 230 species were classified by such detailed uses as furniture mainly and the related small objects, interiors, architecture, exteriors, materials like plywood, toys, musical instrument, exercise equipment, household items, and so on. In addition, some of the terms were clarified such as Madika to Jelutong, Karin to Paudauk and Narra, Red sandalwood to Indian rose wood, and Cherry blossoms from home, the same family as Cherry from abroad but the different species, and so on.

• Journal of Korea Foresty Energy
• /
• v.25 no.1
• /
• pp.9-17
• /
• 2006

Properties of wood charcoal made from the domestic wood species at $300-900^{\circ}C$ have investigated to understand the correlation between carbonization temperature and chemical and physical characteristics of wood charcoal. In terms of charcoal yield at particular carbonization temperatures, it was drastically decreased until the temperature reaches up to $600^{\circ}C$ and the decrease ratio of yield was reduced at higher temperatures. As the carbonization temperature increased, pH of the wood charcoal increased so that it became basic at last. The wood charcoal prepared at $600{\sim}700^{\circ}C$ showed the highest caloric value and those of wood charcoals made at higher temperature became plateau at a little lower level than the peak. The caloric value of Japanese larch charcoal was a bit higher than that of Red oak charcoal. The carbon content in the wood charcoal was increased as the carbonization temperature increased, whereas the hydrogen content was decreased. Specific surface area of the wood charcoal became larger with increase in temperature up to $600^{\circ}C$ but it was decreased or reduced in the increasing ratio after, and then it rose again at higher temperature than $800^{\circ}C$. Absorption capacity of the wood charcoal against iodine and gaseous acetic acid became greater as the carbonization temperature increased. Japanese larch charcoal presented higher absorption capacity than Red oak charcoal. As the above results, it is revealed that carbonization temperature affects the chemical and physical properties of wood charcoal. Therefore, to use wood charcoal with maximum effect it should be prepared at optimum temperature for proper use.

• Proceedings of the Korea Society of Design Studies Conference
• /
• 1998.04a
• /
• pp.24-25
• /
• 1998

• Journal of the Korean Wood Science and Technology
• /
• v.30 no.2
• /
• pp.128-133
• /
• 2002

This study was conducted to investigate the influence of storage time on the sapstain development of Japanese red pine and Korean pine logs during storage in log yard, and their stain characteristics. Japanese red pine and Korean pine trees were harvested and cut into logs in mid January of 2001. These logs were transported to the two local sawmills where they were closely stacked in remote parts of log yard. The logs were then sampled destructively by cutting seven to nine 3-cm long discs along the length of each log at intervals of 3, 4, 5, 6, and 8 month after felling. The stain coverage and maximal radial penetration of stain were measured from the discs of the sampled logs after the isolation of causal staining fungi. The sapstain was primarily infested by the attack of bark beetles and the species of bark beetle was identified as Tomicus piniperda. The main fungal species isolated from stained wood was Ophiostoma species. Based on the present study, the logs could be stored in log yard until May without stain; but stain development was rapid after May and the severity of stain increased proportionally with storage time. Korean pine was more susceptible to fungal stain than Japanese red pine. During summer storage, decay started to develop in logs and the main species were identified as Tyromyces sp. and Schizophyllum commune. Information provided in this paper would be very useful to develop more effective control strategies for sapstain prevention in Japanese red pine and Korean pine logs.