• Proceedings of the Korea Technical Association of the Pulp and Paper Industry Conference
• /
• 2006.06b
• /
• pp.417-421
• /
• 2006

In this study, colloidal Ag solution was spouted on the surface of the inorganic pigment using the hybridizer system and the spray nozzle. Then, the surface of the inorganic pigment was modified by titanium dioxide in order to possess antibacterial ability. Nano-sized colloidal Ag was made by using a seed sol method in this study. It was confirmed that the size of particle per unit weight becomes enlarged, as the addition of $AgNO_{3}$ increased, and as the time of reaction increased, in the manufacturing process of nano-sized colloidal Ag. The antibacterial measurement of the inorganic pigment showed that the growth of fungus was reduced as the reaction time increased. It was measured that the antibacterial activity was excellent at fixed time frame, after the antibacterial ability appeared in $5{\sim}7$ hours of the antibacterial inoculation experiment. The experiment of titanium dioxide's Photocatalyst effect showed $60{\sim}70%$ efficiency in about 80 minute reaction time of the dissolution results regarding measurements of benzene. It was shown that more than 90% of the dissolution efficiency was achieved in the reaction time of about 30 minute.

• Korean Journal of Applied Biomechanics
• /
• v.23 no.3
• /
• pp.225-233
• /
• 2013

The purpose of this study was to estimate the potential injury via analyzing ground reaction force components that were resulted from a prolonged-run-induced fatigue. For the present study, passive and active components of the vertical ground reaction force were determined from time and frequency domain. Shear components of GRF also were calculated from time and frequency domain. Twenty subjects with rear foot contact aged 20 to 30, no experience in injuries of the extremities, were requested to run on the instrumented tread-mill for 160 minutes at their preference running speed. GRF signals for 10 strides were collected at 5, 35, 65, 95, 125, and 155 minute during running. In conclusions, there were no significant difference in the magnitude of passive force, impact load rate, frequency of the passive and active components in vertical GRF between running times except the magnitude of active force (p<.05). The magnitude of active force was significantly decreased after 125 minute run. The magnitude of maximum peak and maximum frequency of the mediolateral GRF at heel strike and toe-off have not been changed with increasing running time. The time up to the maximum peak of the anteroposterior at heel-strike moment tend to decrease (p<.05), but the maximum peak and frequency of that at heel and toe-off moment didn't depend significantly on running time.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.19 no.3
• /
• pp.234-238
• /
• 1990

The effects of salt concentration immersion time in a salt solution prior to air dehydration and heating of air temperature during dehydration upon the browning reaction and pyruvic acid content of air dried garlics to a 6.5% moisture content(wet basis) were analyzed by a response surface methodology(RSM), Those values were also predicted by using a second degree polynomial regression model. Heating of air temperature was the most significant factor affecting the both browning reaction and pyruvic acid content. Salt concentration had more influence to browning reaction than immersion time whereas immersion time was more impor-tant factor than salt concentration on a retention of pyruvic acid sugested different processing conditions. While the processing conditions to minimize the browning reaction(O.D=0.009) were 0.3% of salt solution 9 min of immersion time and 5$0^{\circ}C$ of air temperature compared to control(O.D=0.022) of air dehydration at 5$0^{\circ}C$ Pyruvic acid contents were maximized(174 $\mu$mole/g garlic solid) at the 0.1% of salt solution 3 min of immersion time and 5$0^{\circ}C$ of air temperature compared to control(147 $\mu$mole/g garlic solid) of air dehydration at 5$0^{\circ}C$

• 제어로봇시스템학회:학술대회논문집
• /
• 1992.10a
• /
• pp.947-952
• /
• 1992

A batch reaction calorimeter is the device for estimating reaction heat along time. Reaction heat formation data are very imoprtant for batch reactor behavior analysis and operatoin. So, many types of reaction calorimeter have been introduced and used. In this study, we analyze the dynamic charateristics of the batch reaction calorimeter that is designed in our laboratory. And we introducde suitable temperature control system. As a result, we analyze reatin heat formation data obtained by simulation and introduce its application examples.

• Journal of the Korean Ceramic Society
• /
• v.30 no.1
• /
• pp.34-40
• /
• 1993

ORMOSIL was synthesized with inorganic precursor, TEOS and organic precursor, PDMS, and the variation of composite properties according to the concentration of HCl, solvent content and reaction time were studied. As the concentration of HCl increased, condensation reaction was well proceeded and more regularly distributed network was observed. Increase in reactivity was found with the amount of solvent, and composite had a tendency of forming more porous microstructure as reaction time was increased, which had no influence on the bonding degree.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.31 no.1D
• /
• pp.65-72
• /
• 2011

When an expressway intersects another expressway, a unique connector needs to be designed between the two consecutive exit ramps. In such a case, it is important to design a connector such that there is enough distance for drivers to find their way safely. A current design manual in Korea prescribes the minimum length of the connector as 240 m. In this research, we have suggested a method for calculating the minimum length of a connector in order to check the feasibility of the currently prescribed length. For this purpose, we have attempted to determine the total perception-reaction time and lane-changing time required by a driver. For determining the driver's perception-reaction time, we have used the driver's decision time in addition to the conventional 2.5 s of perception-reaction time for stopping sight distances. We have considered both the design speed and the average travel speed for the calculation of the length. To evaluate the accuracy of the new method, we have chosen four sites on expressways for which relatively high accident rates were recorded. As a result, we could verify that the current limit (240 m) was sufficient for drivers to be able to change lanes in the given specific geometry. However, the prescribed limit should be revised in case the drivers' decision time is considered to be their perception-reaction time. All new approaches for calculating the ideal length of a connector have been carried out by taking into account the design speed as well as the average travel speed. Owing to the characteristics of the specific geometry for two consecutive exit ramps and the large difference between the design speed and the average travel speed in the objective areas, it is more realistic to use the proposed method by keeping the decision time equal to a driver's perception-reaction time, in order to determine the ideal distance that should be maintained between two consecutive exit ramps.

• KSBB Journal
• /
• v.26 no.4
• /
• pp.341-346
• /
• 2011

This work is focused on the possibility of marine biomass Codium fragile as renewable resources for production of levulinic acid. In an effort to optimize the reaction conditions of levulinic acid production from Codium fragile, response surface methodology was applied. A total of 18 individual experiments were designed to investigate the effect of reaction temperature, catalyst amount, and reaction time. As a result, 4.26 g/L levulinic acid from Codium fragile was produced in the condition of $160.7^{\circ}C$ of reaction temperature, 3.9% of sulfuric acid, and 39.1 min of reaction time. This result will provide the useful information for chemical production from marine resource.

• Journal of the Korean Ceramic Society
• /
• v.36 no.6
• /
• pp.655-661
• /
• 1999

${\beta}$-SiC formation mechanism in Si melt-C-SiC system with varying in size of carbon source was investigated. A continuous reaction sintering process using Si melt infiltration method was adopted to control the reaction sintering time effectively. It was found that ${\beta}$-SiC formation mechanism in Si melt-C-SiC system was directly affected by the size of carbon source. In the Si melt-C-SiC system with large carbon source ${\beta}$-SiC formation mechanism could be divided into two stages depending on the reaction sintering time: in early stage of reaction sintering carbon dissolution in Si melt and precipitation of ${\beta}$-SiC was occurred preferentially and then SIC nucleation and growth was controlled by diffusion of carbon throughy the ${\beta}$-SiC layer formed on graphite particle. Furthmore a dissolution rate of graphite particles in Si melt could be accelerated by the infiltration of Si melt through basal plane of graphite crystalline.

• Journal of Powder Materials
• /
• v.4 no.3
• /
• pp.196-204
• /
• 1997

Joining of AIN ceramics to W and Cu by active-metal brazing method was tried with use of (Ag-Cu)-Ti alloy as insert-metal. Joints were produced under various conditions of temperature, holding time and Ti-content in (Ag-Cu) alloy Reaction and microstructural development in bonded interface were investigated through observation and analysis by SEM/EDS, EPMA and XRD. Joint strengths were measured by shear test. Bonded interface consists of two layers: an insert-metal layer of eutectic Ag- and Cu-rich phases and a reaction layer of TiN. Thickness of reaction layer increases with bonding temperature, holding time and Ti-content of insert-metal. It was confirmed that the growth of reaction layer is a diffusion-controlled process. Activation energy for this process was 260 KJ/mol which is lower than that for N diffusion in TiN. Maximum shear strength of 108 MPa and 72 MPa were obtained for AIN/W and AIN/Cu joints, respectively. Relationship between processing variables, joint strength and thickness of reaction layer was also explained.

• Journal of Powder Materials
• /
• v.6 no.2
• /
• pp.178-185
• /
• 1999

MoSi$_2$-TiC composite powders were fabricated by in-situ reaction through mechanical alloying. Also the monolithic MoSi$_2$ as well as TiC were synthesiced by mechanical alloying for comparison. An abrupt increase of vial surface temperature was detected due to a sudden reaction between elemental powders during milling. The reaction time for synthesis of composite powders decreased with increasing the content of (Ti+C) powder. It was found that a significant decrease of Ti grain size was observed with increasing the milling time. And the synthesis reaction of MoSi$_2$-TiC composite powders were largely dependent on the reaction between Ti and C powders.