• Journal of the Institute of Electronics and Information Engineers
• /
• v.50 no.12
• /
• pp.247-253
• /
• 2013

The purpose is a comparative evaluation in the DR System according to the dosimetry and image quality of the quantitative and objective via Direct digital radiography, Indirect digital radiography, Image intensifier (Charge Coupled Device type) digital radiography. The experimental method used rando phantom and measured the entrance surface dose. And through using the measured entrance surface dose and then using the PCXMC program were evaluated risk due to irradiation and the effective dose. SNR and NPS and CNR were measured and analyzed by using 21cm acryl phantom. Significance of measured value was evaluated by statistics method. Entrance surface dose, major organ dose, effective dose all of them were measured the lowest rated in direct DR when it is on the basis of direct DR dose, high-dose ratio were measured in I.I DR approximately 1.3 times, indirect DR approximately 2.4 times. Risk in accordance with radiation also was measured same as dose ratio. On the conclusion that SNR measurement result based on direct DR SNR measurements, low-SNR ratio were measured in I.I DR approximately 7.25 times, indirect DR approximately 1.48 times. On the conclusion that CNR measurement result based on direct DR CNR measurements, high-dose ratio were measured in I.I type DR approximately 1.16 tims and low-dose ratio were measured in indirect DR approximately 0.87 times. Therefore Direct DR system using a-selenium sensing element to detect x-ray photon is thought effectively at the examination such as infant to sensitive irradiation and the genital gland. Because quality image is built by low dose. Also when it is necessary that image test requiring many diagnosis information, indirect DR system is thought effectively.

• Journal of the Korean Chemical Society
• /
• v.61 no.2
• /
• pp.51-56
• /
• 2017

N-nitrosamines are the nitroso compounds which are produced by nitrosation reactions of the secondary amine and nitrite under acidic conditions. Approximately 300 species of N-nitrosamine have been tested for carcinogenicity in laboratory experiments, with 90% of them demonstrated carcinogenic effects different animal species, including higher primates. In 1978, IARC classified NDMA and NDEA as Group 2A, and NDPA, NDBA, NPIP, NPYR and NMOR as Group 2B. In this study, we established pretreatment and analytical method for N-nitrosamines (NDMA, NDEA, NMEA, NDPA, NDBA, NPIP, NPYR and NMOR) in human urine for biological monitoring of N-nitrosamines. The analytes were extracted using solid phase extraction (SPE), then quantitative analysis was performed by LC-(APCI)-MS/MS. The accuracies of the established method were between 85.8~108.7% and precisions were lower than 20%. The limit of detection (LOD) were between 0.0002 (NDBA) and 0.0793 (NDMA) ng/ml. The linearity obtained was satisfying for the 8 N-nitrosamines, with a coefficient of determination ($r^2$) higher than 0.999. The mean concentrations of N-nitrosamines in the urine were 2.645 mg/g creatinine for NDMA, 0.067 mg/g creatinine for NDEA, 0.009 mg/g creatinine for NMEA, 0.011 mg/g creatinine for NDBA, 0.271 mg/g creatinine for NPIP and 0.413 mg/g creatinine for NPYR. NDPA and NMOR were not detected. It can be used as a instrumental methodology for evaluation and risk assessment of human exposure to N-nitrosamines for the further research.

• Journal of the Korean Geotechnical Society
• /
• v.28 no.10
• /
• pp.5-16
• /
• 2012

Geotechnical buried structures with relatively light weight have been suffering from uplift damage due to liquefaction in the past earthquakes. The factor of safety approach by Koseki et al. (1997a), which is widely used in seismic design, predicts the triggering of uplift. However, a method for "quantitative" estimates of the uplift displacement has yet to be established. Estimation of the uplift displacement may be an important factor to be considered for designing underground structures under the framework of performance-based design (ISO23469, 2005). Therefore, evaluation of the uplift displacement of buried structure in liquefied ground during earthquakes is needed for a performance-based design as a practical application. In order to predict the uplift displacement quantitatively, a simplified method is derived based on the equilibrium of vertical forces acting on buried structures in backfill during earthquakes (Tobita et al., 2012). The method is verified through comparisons with results of centrifuge model tests and damaged sewerage systems after the 2004 Niigata-ken Chuetsu, Japan, earthquake. The proposed flow diagram for performance-based design includes estimation of the uplift displacement as well as liquefaction limit of backfill.

• Journal of Distribution Science
• /
• v.13 no.4
• /
• pp.89-98
• /
• 2015

Purpose - In today's globalized and modern business environment, corporate social responsibility (CSR) activities are considered to be essential for the sustainable development of enterprises. In addition, the corporate philanthropy that is related to CSR practices, as well as their being capable of reducing the anti-corporate sentiment of people have facilitated a qualitative forward leap into the quantitative growth phase. This study aims to undertake a comparative evaluation of corporate philanthropy through the Importance-Performance Analysis (IPA) method focusing on service and manufacturing industries, and to eventually determine a differentiated approach that is needed for corporate philanthropy. Research design, data, and methodology - The survey responses were collected through online research on specialized companies from consumers nationwide who were aged from 20 to 60 and who are aware of corporate philanthropy. A total of 408 sheets of questionnaire survey were used. Frequency analysis was undertaken in this study. The interviewees had demographic characteristics of gender: 206 males (50.5%) and 202 females (49.5%). They also had demographic characteristics of age: 82 people were over 20 (20.1%), 96 over 30 (23.5%), 105 over 40 (25.7%), and 125 over 50 (30.7%) years of age. The distribution of interviewees' residences is as follows: 154 persons (37.7%) in the Special City, 102 persons (25.0%) in the Metropolitan City, and 152 persons (37.3%) in the Provincial Region. The interviewees have been working for the following companies: 34 persons (8.3%) in LG Display, 80 (19.6%) in KT&G, 49 (12.0%) in Amore Pacific, 42 (10.3%) in KIA Motors, 47 (11.5%) in SBS, 52 (12.8%) in Shinhan Bank, 86 (21.1%) in Asiana Airlines, and 18 (4.4%) in Hyundai Department Store. We applied the paired t-test for the IPA analysis. PASW Statistics 18 was used for statistical analysis. Results - The results of IPA analysis indicated that the importance and performance degrees in both manufacturing and service industries were significantly different. Major empirical results showed that, in consumer, social, economic, philanthropic, and environmental dimensions, in the sub-factors of philanthropy activities in both manufacturing and service industries, the importance degree was found to be higher than performance degree. Further, the average difference between importance degree and performance degree by the sub-factors of philanthropy activities. On the other hand, the average difference of environmental dimension was found to be highest in both service and manufacturing industries. Thus, while consumers consider the philanthropy activities of the environmental dimension as most important, actual companies treat performance of philanthropy activities of the environmental dimension insufficiently or negligibly to some degree. Conclusions - The differentiated approach method that is required for corporate philanthropy may be proposed to uplift corporate accomplishments by analyzing the IPA of the attributes of the sub-factors of corporate philanthropy. This is, to an extent, insufficient in the existing studies related to the use of the IPA technique, and it shows the items that are to be conducted intensively.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.21 no.10
• /
• pp.55-63
• /
• 2020

Road traffic noise is a major complaint. Porous pavement (PP) has been proposed as an effective method for reducing road traffic noise, but it has not been applied much due to the lack of quantitative evaluation. In this study, the noise reduction of single-layer porous pavement (SLPP) and double-layer porous pavement (DLPP) was evaluated. The noise was measured using the CPX method, and the driving speed was measured every 10km/h from 50km/h to 80km/h. The differences in noise level between the two PPs were statistically significant. The driving speed had no significant effect on the difference in noise between the two PPs. The DLPP showed a 6.6dB(A) reduction in average and a 6.3dB(A) reduction at the 95% confidence level compared to the SLPP. Reducing noise by 5dB(A) is equivalent to reducing traffic to 1/3 or lowering the vehicle's speed to 1/2. Sensitively, it is possible to recognize a 3dB(A) and 5dB(A) difference. The DLPP and SLPP were very effective in reducing traffic noise.

• Journal of the Korean Society of Radiology
• /
• v.14 no.1
• /
• pp.45-51
• /
• 2020

The purpose of this study was to analyze the educational effect of self-directed learning method using 3D printed anatomy on radiological science students. The subjects were 32 students (20 males and 12 females) in the second year of radiological science at university. They were divided two groups as a non-active student group and an active student group. A learning method was self-directed learning using 3D printed anatomical structures, and the effects of quantitative learning improvement were evaluated before and after the learning. The qualitative evaluation of the students was analyzed on the Likert's 5-point scale for the interest, satisfaction, and learning effects (memorization convenience of anatomy name, radiography Interpret ability, understanding on bones structure, and X-ray projection technique). As a result, the enhancement of learning improved 65.4% on average, and all students got scored high on all variables. Especially non-active student groups showed higher correlation coefficients in all variables except interest and radiography interpret than active student groups. These results might suggest that self-directed learning using 3D printed anatomical structures could have a positive educational effect on radiological science students.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.18 no.2
• /
• pp.108-116
• /
• 2014

The proper stress history measurement should be conducted in order to examine the accurate cause of fatigue cracks or the fatigue safety in the steel bridge. Only one strain gauge is generally installed in the field for the stress history examination because of the field circumstances, economic feasibility, workability, and so on. However, this method may not consider the actual size of the specific structure, the gauge length, and the affect of stress concentration in the welded joint. In addition, it is difficult to apply for the stress analysis. Therefore, this study suggests improvements that are a great number of gauge installations, the gauge location adjustment, and the use of the minimum length gauge. It is drived the correlative equation of strain for the distance between the welding toe and the strain gauge installation, and compare correlative equation with equation of IIW. Also, this study could estimate the remaining life and fatigue damage of bridge in service by selecting the suitable stress category. In conclusion, it is possible to understand the member which is high in the fatigue cracks, and the quantitative relations between the welding toe and the strain gauge installation distances. The proposed approach in this study can make an more accurate fatigue damage and a remaining life prediction so that the improved method should be applied in measuring the strain of bridges from now on.

• Journal of the Earthquake Engineering Society of Korea
• /
• v.13 no.3
• /
• pp.11-19
• /
• 2009

Recently, concerns relating to the maintenance of large structures have been increased. In addition, the number of large structures that need to be evaluated for their structural safety due to natural disasters and structural deterioration has been rapidly increasing. It is common for the structural characteristics of an older large structure to differ from the characteristics in the initial design stage, and changes in dynamic characteristics may result from a reduction in stiffness due to cracks on the materials. The process of deterioration of such structures enables the detection of damaged locations, as well as a quantitative evaluation. One of the typical measuring instruments used for the monitoring of bridges and buildings is the dynamic measurement system. Conventional dynamic measurement systems require considerable cabling to facilitate a direct connection between sensor and DAQ logger. For this reason, a method of measuring structural responses from a remote distance without the mounted sensors is needed. In terms of non-contact methods that are applicable to dynamic response measurement, the methods using the doppler effect of a laser or a GPS are commonly used. However, such methods could not be generally applied to bridge structures because of their costs and inaccuracies. Alternatively, a method using a visual image can be economical as well as feasible for measuring vibration signals of inaccessible bridge structures and extracting their dynamic characteristics. Many studies have been conducted using camera visual signals instead of conventional mounted sensors. However, these studies have been focused on measuring displacement response by an image processing technique after recording a position of the target mounted on the structure, in which the number of measurement targets may be limited. Therefore, in this study, a model experiment was carried out to verify the measurement algorithm for measuring multi-point displacement responses by using a DIC (Digital Image Correlation) technique.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.21 no.5
• /
• pp.465-474
• /
• 2008

The real-time hybrid testing method(RT-HYTEM) is a structural testing technique in which the numerical integration of the equation of motion for a numerical substructure and the physical testing for an experimental substructure are performed simultaneously in real-time. This study presents the quantitative evaluation of the seismic performance of a building structure installed with an passive and semi-active MR damper by using RT-HYTEM. The building model that was identified from the force-vibration testing results of a real-scaled 5-story building is used as the numerical substructure, and an MR damper corresponding to an experimental substructure is physically tested by using the universal testing machine(UTM). The RT-HYTEM implemented in this study is validated because the real-time hybrid testing results obtained by application of sinusoidal and earthquake excitations and the corresponding analytical results obtained by using the Bouc-Wen model as the control force of the MR damper respect to input currents were in good agreement. Also for preliminary study, some semi-active control algorithms were applied to the MR damper in order to control the structural responses optimally. Comparing between the test results of semi-active control using RT-HYTEM and numerical analysis results show that the RT-HYTEM is more resonable than numerical analysis to evaluate the performance of semi-active control algorithms.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.51 no.7
• /
• pp.180-189
• /
• 2014

Display quality assessment has been a long standing issue due to the diversity of display devices and the rapid growth of display technology. The conventional display quality assessment methods are mostly those methods which evaluate qualities of a display by measuring physical quantities, but the results from the methods are not equal to the perceived results which are acquired with subjective experiments. Thus, we need to solve the above contrariety as well as establish the quantitative correlation between physical and perceived results. This paper proposes the systematic method of evaluating relative perceived qualities among various display devices and quantifies these relative perceived qualities. The proposed method is based on Analytic Network Process(ANP), which is one of the most popular decision making methods in the business administration field. We also adopted three evaluation criteria, which consist of color, shape and depth, in order to reflect the human visual system and chose eight sub-criteria related to display characteristics via question investigation. We carried out a subjective experiment and the proposed method which evaluated perceived qualities of two display devices(TFT-LCD, OLED) in order to prove the similarity between their results. As a result, it is proved that the order relationship between perceived qualities was the same as the order of results got through the subjective experiment.