• 한국항해항만학회지
• /
• 제30권10호
• /
• pp.869-875
• /
• 2006

본 연구에서는 최적화기법과 전산유체역학의 기술을 이용하여 저항의 관점에서 최적의 형상을 가지는 선형을 개발하는 알고리즘을 개발하였다. 최적화기법으로는 SQP(sequential quadratic programming)을 사용하였으며, 목적함수인 저항을 구하기 위하여 먼저 조파저항은 비선형 자유수면 경계조건을 고려한 선체주위 포텐셜유동을 계산할 수 있는 수치해석기법인 상 방향 패널이동법을 사용하였고, 선체에 미치는 전 저항을 구하기 위하여 ITTC 1957년 모형선-실선상관곡선을 이용하였다. 선형최적화 과정 중의 선체의 변경이나 계산 격자의 생성은 NURBS(Non-Uniform Rational B-Spline)기법을 사용하여 구현하였다. 이와 같은 방법을 사용하여 개발된 선형최적화 기법의 타당성을 검증하기 위하여 선형이 비교적 잘 알려진 건형인 Wigley선형과 Series 60(CB=0.6)선형에 대하여 설계속도 Fn=0.316에서 선형최적화를 위한 수치해석을 수행하고 그 결과를 초기선형과 서로 비교하였다.

• 한국항해항만학회:학술대회논문집
• /
• 한국항해항만학회 2005년도 춘계학술대회 논문집
• /
• pp.47-53
• /
• 2005

본 연구에서는 최적화기법과 전산유체역학의 기술을 이용하여 저항의 관점에서 최적의 형상을 가지는 선형을 개발하는 알고리즘을 개발하였다. 최적화기법으로는 SQP(sequential quadratic programming)을 사용하였으며, 목적함수인 저항을 구하기 위하여 먼저 조파저항은 비선형자유수면경계조건을 고려한 선체주위 포텐셜유동을 계산할 수 있는 수치해석기법인 상방향패널이동법을 사용하였고, 선체에 미치는 전저항을 구하기 위하여 ITTC 1957년 모형선-실선상관곡선을 이용하였다. 선형최적화 과정 중의 선체의 변경이나 계산 격자의 생성은 NURBS(Non-Uniform Rational B-Spline)기법을 사용하여 구현하였다. 이와 같은 방법을 사용하여 개발된 선형최적화 기법의 타당성을 검증하기 위하여 선형이 비교적 잘 알려진 선형인 Wigley선형과 Series 60(C${_B}$=0.6)hull 선형에 대하여 설계속도 Fn=0.316에서 선형최적화를 위한 수치해석을 수행하고 그 결과를 초기선형과 서로 비교하였다.

• 대한조선학회지
• /
• 제16권2호
• /
• pp.9-14
• /
• 1979

Havelock was considered the wave resistance of a post extending vertically downwards through the water from the surface, its section by a horizontal plane being the same at all depths and having its breath small compared with its length. This enables us to elucidate certain points of interest in ship resistance. However, the ship has not infinte draft. So, the problem which is investigated in detail in this paper is the wave resistance of a mathematical quadratic model in a uniform stream. The author wishes to study the effect of viriation of draft. The form of the water-plane is varied while keeping in length and the cross sectional area constant. As a numerical example, we calculated the wave resistance for mathematical quadratic ship models. The results are compared with a post having infinite depth. The results are as follows; The models with finer ends have smaller wave resistance up to $V/\sqrt{L}=1.1{\sim}1.2$ than its mate with blunter ends, but above this speed the models with blunter ends have less wave resistance. According to the decrease of draft, the wave resistance gap between the models with blunter ends the models with finer ends decrease at high speed. In this case of T/L=0.025, the models with finer ends have less wave resistance than the models with blunter ends at high speed.

• 대한수학회지
• /
• 제38권3호
• /
• pp.595-611
• /
• 2001

Let Q(n,1) be the set of even unimodular positive definite integral quadratic forms in n-variables. Then n is divisible by 8. For A[X] in Q(n,1), the theta series $\theta$(sub)A(z) = ∑(sub)X∈Z(sup)n e(sup)$\pi$izA[X] (Z∈h (※Equations, See Full-text) the complex upper half plane) is a modular form of weight n/2 for the congruence group Γ$_1$(8) = {$\delta$∈SL$_2$(Z)│$\delta$≡()mod 8} (※Equation, See Full-text). If n$\geq$24 and A[X], B{X} are tow quadratic forms in Q(n,1), the quotient $\theta$(sub)A(z)/$\theta$(sub)B(z) is a modular function for Γ$_1$(8). Since we identify the field of modular functions for Γ$_1$(8) with the function field K(X$_1$(8)) of the modular curve X$_1$(8) = Γ$_1$(8)＼h(sup)* (h(sup)* the extended plane of h) with genus 0, we can express it as a rational function of j(sub) 1,8 over C which is a field generator of K(X$_1$(8)) and defined by j(sub)1,8(z) = $\theta$$_3$(2z)/$\theta$$_3$(4z). Here, $\theta$$_3$ is the classical Jacobi theta series.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 춘계학술대회논문집C
• /
• pp.386-391
• /
• 2001

This paper presents a new two-point approximation method based on the exponential intervening variable. To avoid the lack of definition of the conventional exponential intervening variables due to zero- or negative-valued design variables the shifting level into each exponential intervening variable is introduced. Then a new quadratic approximation, whose Hessian matrix has only diagonal elements of different values, is proposed in terms of these intervening variables. These diagonal elements are computed in a closed form, which correct the typical error in the approximate gradient of the TANA series due to the lack of definition of exponential type intervening variables and their incomplete second-order terms. Also, a correction coefficient is multiplied to the pre-determined quadratic term to match the value of approximate function with that of the original function at the previous point. Finally, the authors developed a sequential approximate optimizer, solved several typical design problems used in the literature and compared these optimization results with those of TANA-3. These comparisons show that the proposed method gives more efficient and reliable results than TANA-3.

• Advances in Computational Design
• /
• 제5권4호
• /
• pp.397-416
• /
• 2020

Functionally graded material (FGM) illustrates a novel class of composites that consists of a graded pattern of material composition. FGM is engineered to have a continuously varying spatial composition profile. Current work focused on buckling analysis of beam made of stepwise linear and quadratic graded material in axial direction subjected to axial span-load with piecewise function and rested on shear layer based on classical beam theory. The various boundary and natural conditions including simply supported (S-S), pinned - clamped (P-C), axial hinge - pinned (AH-P), axial hinge - clamped (AH-C), pinned - shear hinge (P-SHH), pinned - shear force released (P-SHR), axial hinge - shear force released (AH-SHR) and axial hinge - shear hinge (AH-SHH) are considered. To the best of the author's knowledge, buckling behavior of this kind of Euler-Bernoulli beams has not been studied yet. The equilibrium differential equation is derived by minimizing total potential energy via variational calculus and solved analytically. The boundary conditions, natural conditions and deformation continuity at concentrated load insertion point are expressed in matrix form and nontrivial solution is employed to calculate first buckling loads and corresponding mode shapes. By increasing truncation order, the relative error reduction and convergence of solution are observed. Fast convergence and good compatibility with various conditions are advantages of the proposed method. A MATLAB code is provided in appendix to employ the numerical procedure based on proposed method.

• Journal of Mechanical Science and Technology
• /
• 제15권9호
• /
• pp.1257-1267
• /
• 2001

For efficient mechanical system optimization, a new two-point approximation method is presented. Unlike the conventional two-point approximation methods such as TPEA, TANA, TANA-1, TANA-2 and TANA-3, this introduces the shifting level into each exponential intervening variable to avoid the lack of definition of the conventional exponential intervening variables due to zero-or negative-valued design variables. Then a new quadratic approximation whose Hessian matrix has only diagonal elements of different values is proposed in terms of these shifted exponential intervening variables. These diagonal elements are determined in a closed form that corrects the typical error in the approximate gradient of the TANA series due to the lack of definition of exponential type intervening variables and their incomplete second-order terms. Also, a correction coefficient is multiplied to the pre-determined quadratic term to match the value of approximate function with that of the previous point. Finally, in order to show the numerical performance of the proposed method, a sequential approximate optimizer is developed and applied to solve six typical design problems. These optimization results are compared with those of TANA-3. These comparisons show that the proposed method gives more efficient and reliable results than TANA-3.

• 대한기계학회논문집A
• /
• 제25권9호
• /
• pp.1423-1431
• /
• 2001

Based on the exponential intervening variable, a new two-point approximation method is presented. This introduces the shifting level into each exponential intervening variable to avoid the lack of def inition of the conventional exponential intervening variables due to zero-or negative-valued design variables. Then a new quadratic approximation whose Hessian matrix has only diagonal elements of different values is proposed in terms of these intervening variables. These diagonal elements are determined in a closed form that corrects the typical error in the approximate gradient of the TANA series due to the lack of definition of exponential type intervening variables and their incomplete second-order terms. Also, a correction coefficient is multiplied to the pre-determined quadratic term to match the value of approximate function with that of the previous point. Finally, in order to show the numerical performance of the proposed method, a sequential approximate optimizer is developed and applied to solve six typical design problems. These optimization results are compared with those of TANA-3. These comparisons show that the proposed method gives more efficient and reliable results than TANA-3.

• 대한조선학회지
• /
• 제12권1호
• /
• pp.41-46
• /
• 1975

This paper was intended to compare the relationship between sectional form of ships and wave making resistance by calculating the resistance value practically rather than theoretically. As the sectional form of ships, four types of quadratic ship forms was introduced and he wave making resistance was calculated by the Slender Ship Theory. The main result obtained in this paper is the following. The relationship between the displacement distribution of draught direction in the given sectional form of ships and the resistance value was shown. It was supposed that the resistance value will decrease with the increase of the displacement distribution of draught direction and it was proved by the numerical value.

• International Journal of Ocean System Engineering
• /
• 제3권1호
• /
• pp.1-9
• /
• 2013

A design procedure for a ship with minimum resistance had been developed using a numerical optimization method called SQP (Sequential Quadratic Programming) combined with computational fluid dynamics (CFD) technique. The frictional resistance coefficient was estimated by the ITTC 1957 model-ship correlation line formula and the wave-making resistance coefficient was evaluated by the potential-flow panel method with the nonlinear free surface boundary conditions. The geometry of the hull surface was represented and modified by B-spline surface modeling technique during the optimization process. The Series 60 ($C_B$=0.60) hull was selected as a parent hull to obtain an optimized hull that produces minimum resistance. The models of the parent and optimized hull forms were tested at calm water condition in order to demonstrate the validity of the proposed methodolgy.