• 한국표면공학회지
• /
• 제46권3호
• /
• pp.133-138
• /
• 2013

We have developed a 2D axi-symmetric numerical model for an inductively coupled plasma system in order to analyze gas mixing effect through a narrow gap shower head. For frictional flow, holes of 0.5 mm diameter and 2 mm length are approximately modeled in 2D. Gas velocity distribution 10 mm below the shower head showed 2 times difference between the center and the edge at 10 mTorr. At 10 mm above the wafer, it was increased to 6 times difference due to the pumping duct effect. The model with a 5 mm height buffer region of a shower head showed reasonable behavior of Ar discharge. The density of Ar metastable showed additional peak inside the buffer region around the edge holes.

• 한국자동차공학회논문집
• /
• 제11권2호
• /
• pp.203-210
• /
• 2003

A simulation study was carried to analyze the vehicle fuel consumption on component basis. Experiments was also carried out to identify the simulation results, under FTP-75 Hot Phase driving conditions. and arbitrary driving conditions. A good quantitative agreement was obtained. Based on the simulation, fuel energy was used in pumping loss(3.7%), electric power generation(0.7%), engine friction(12.7%), engine inertia(0.7%), torque converter loss(4.6%), drivetrain friction(0.6%), road-load(9.2%), and vehicle inertia(13.4%) under FTP-75 Hot Phase driving conditions. Using simulation program, the effects of capacity factor and idle speed on fuel consumption were estimated. A increment of capacity factor of torque converter resulted in fuel consumption improvement under FTP-75 Hot Phase driving conditions. Effect of a decrement of idle speed on fuel consumption was negligible under the identical driving conditions.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2004년도 춘계학술대회
• /
• pp.1189-1194
• /
• 2004

In this paper, the effect of tip clearance on the cooling performance of the microchannel heat sink is presented under the fixed pumping power condition. For the various types of microchannel heat sink having different size of fin width and channel width, experimental study is conducted. Through the experiment, the tip clearance effect is investigated by increasing tip clearance from zero. As a result, it is shown that cooling performance of heat sink with tip clearance is better than that of heat sink without tip clearance. For the microchannel heat sink with tip clearance, the optimum conditions for cooling performance is also studied.

• 상하수도학회지
• /
• 제28권3호
• /
• pp.315-324
• /
• 2014

The residents' odor complaint is steadily increasing by odor causing from sewage system. A current drainage facilities and septic tank are included in the individual sewerage according to Sewerage Act. However, definitions and legal standards of drainage tank are insufficient. In addition, specifications and maintenance standards related to structure and size are not established. In this research, effect of drainage tank in individual sewage facilities on the odor occurrence was studied and the concentrations of $H_2S$ and composite odor were measured. From the measurements, the concentration of $H_2S$ and composite odor were 1 ppm ~ 5 ppm and 1.04 OU ~ 4.05 OU, respectively, before pump operation. Also, the concentration of $H_2S$ and composite odor were 5 ppm ~ 33 ppm and 5.10 OU ~ 35.04 OU, respectively, after pump operation. The concentration of SS in the effluent from drainage tank was ranged from 840 mg/L to 1,980 mg/L. These high concentration of SS seemed to be the major source of foul smell when high concentrated suspended solids in the public sewerage system were decomposed and then emitted. In this research, correlation coefficient ($R^2$) between $H_2S$ and composite odor before and after pumping were 0.925 and 0.918, respectively.

• 한국수자원학회논문집
• /
• 제37권2호
• /
• pp.97-108
• /
• 2004

최근 들어 도서지역이나 해안지역의 제한된 수자원을 보다 효과적으로 사용하기 위하여 지하댐을 이용한 지하수자원 개발 방안이 제시되고 있다. 그러나 해안선에 인접한 지하댐의 경우 과도한 지하수 양수는 대수층의 지하수위를 저하시켜 결국 염수침입이라는 심각한 문제를 발생시키게 된다. 염수침입은 대수층의 지하수위 하강에 기인하므로 본 연구에서는 지하댐 하류에 함양정(Recharging well)을 설치하여 대수층의 지하수위를 상승시킴에 따른 염수침입 저감효과를 분석하였다. 이 방안을 쌍천유역에 적용하였으며, 이를 위해 염분의 이송ㆍ확산을 분석할 수 있는 SUTRA(Saturated-Unsaturated Transport) 수치모형을 적용하였다. 그 결과 지하댐 하류지역에 대한 함양기법이 양수정 염분 저하에 매우 효율적인 방법임이 증명되었고, 염해저감을 위한 함양정 운영시 차수벽으로부터 40∼60m거리에 함양정을 설치하고 함양률을 총 양수량의 6∼7％정도로 하여 운영을 할 때 가장 효율적으로 염해를 저감시킬 수 있다는 결론을 얻을 수 있었다.

• Nuclear Engineering and Technology
• /
• 제40권3호
• /
• pp.213-224
• /
• 2008

The pumping of coolant in a liquid metal fast reactor may be performed with an annular linear induction electro-magnetic (EM) pump. Linear induction pumps use a traveling magnetic field wave created by poly-phase currents, and the induced currents and their associated magnetic field generate a Lorentz force, whose effect can be the pumping of the liquid metal. The flow behaviors in the pump are very complex, including a time-varying Lorentz force and pressure pulsation, because an induction EM pump has time-varying magnetic fields and the induced convective currents that originate from the flow of the liquid metal. These phenomena lead to an instability problem in the pump arising from the changes of the generated Lorentz forces along the pump's geometry. Therefore, a magneto-hydro-dynamics (MHD) analysis is required for the design and operation of a linear induction EM pump. We have developed a time-harmonic 2-dimensional axisymmetry MHD analysis method based on the Maxwell equations. This paper describes the analysis and numerical method for obtaining solutions for some MHD parameters in an induction EM pump. Experimental test results obtained from an induction EM pump of CLIP-150 at the STC "Sintez," D.V. Efremov Institute of Electro-physical Apparatus in St. Petersburg were used to validate the method. In addition, we investigated some characteristics of a linear induction EM pump, such as the effect of the convective current and the double supply frequency (DSF) pressure pulsation. This simple model overestimated the convective eddy current generated from the sodium flow in the pump channel; however, it had a similar tendency for the measured data of the pump performance through a comparison with the experimental data. Considering its simplicity, it could be a base model for designing an EM pump and for evaluating the MHD flow in an EM pump.

• 대한전자공학회논문지SD
• /
• 제45권7호
• /
• pp.37-43
• /
• 2008

본 논문에서는 전하 펌프 방법 (Charge Pumping Method, CPM)를 이용하여 서로 다른 질화막 층을 가지는 N-Channel SANOS (Silicon-$Al_2O_3$-Nitride-Oxide-Silicon) Flash Memory Cell 트랜지스터의 트랩 특성을 규명하였다. SANOS Flash Memory에서 계면 및 질화막 트랩의 중요성은 널리 알려져 있지만 소자에 직접 적용 가능하면서 정화하고 용이한 트랩 분석 방법은 미흡하다고 할 수 있다. 기존에 알려진 분석 방법 중 전하 펌프 방법은 측정 및 분석이 간단하면서 트랜지스터에 직접 적용이 가능하여 MOSFET에 널리 사용되어왔으며 최근에는 MONOS/SONOS 구조에도 적용되고 있지만 아직까지는 Silicon 기판과 tunneling oxide와의 계면에 존재하는 트랩 및 tunneling oxide가 얇은 구조에서의 질화막 벌크 트랩 추출 결과만이 보고되어 있다. 이에 본 연구에서는 Trapping Layer (질화막)가 다른 SONOS 트랜지스터에 전하 펌프 방법을 적용하여 Si 기판/Tunneling Oxide 계면 트랩 및 질화막 트랩을 분리하여 평가하였으며 추출된 결과의 정확성 및 유용성을 확인하고자 트랜지스터의 전기적 특성 및 메모리 특성과의 상관 관계를 분석하고 Simulation을 통해 확인하였다. 분석 결과 계면 트랩의 경우 트랩 밀도가 높고 trap의 capture cross section이 큰 소자의 경우 전자이동도, subthreshold slop, leakage current 등의 트랜지스터의 일반적인 특성 열화가 나타났다. 계면 트랩은 특히 Memory 특성 중 Program/Erase (P/E) speed에 영향을 미치는 것으로 나타났는데 이는 계면결함이 많은 소자의 경우 같은 P/E 조건에서 더 많은 전하가 계면결함에 포획됨으로써 trapping layer로의 carrier 이동이 억제되기 때문으로 판단되며 simulation을 통해서도 동일한 결과를 확인하였다. 하지만 data retention의 경우 계면 트랩보다 charge trapping layer인 질화막 트랩 특성에 의해 더 크게 영향을 받는 것으로 나타났다. 이는 P/E cycling 횟수에 따른 data retention 특성 열화 측정 결과에서도 일관되게 확인할 수 있었다.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 춘계학술대회논문집D
• /
• pp.408-413
• /
• 2001

Numerical analysis on the three-dimensional laminar flows (Re=1000) and heat transfer in a rectangular channel with punched longitudinal vortex generator have been conducted to explore the heat transfer enhancement and the combined effect of the angle of attack ${\alpha}$ and the lovour angle ${\beta}$. Rectangular winglets have been used as vortex generators. Velocity and temperature fields and spanwise averaged Nu and friction factor were presented. Enhancement of heat transfer and flow loss penalty are evidenced. The results show performance characteristics allowing a reduction in heat transfer surface area of 62% for fixed heat duty and for fixed pumping power compared with that of channel flow without vortex generator. However, adding lovour angle to the vortex generator shows no positive effect on the heat transfer enhancement.

• Corrosion Science and Technology
• /
• 제10권1호
• /
• pp.30-36
• /
• 2011

The effect of dynamic flow or forced convection were investigated and compared on the formation of inhibition layer, galvanizing and galvannealing reactions through the hot-dip galvanizing simulator with the oscillation of specimen in zinc bath, continuous galvanizing pilot plant with zinc pumping system through the snout and continuous galvanizing operation with Dynamic $Galvanizing^{TR}$ system. The interfacial Al pick-up was not consistent between the results of simulator, pilot plant and line operation, but the morphology of inhibition layer became compact and refined by the forced convection. The growth of Fe-Zn intermetallics at the interface was inhibited by the forced convection, whereas the galvannealing rate would be a little promoted.

• 대한전자공학회논문지SD
• /
• 제40권9호
• /
• pp.638-643
• /
• 2003

Channel width dependence of hot-carrier effect in nMOSFET with shallow trench isolation is analyzed. $I_{sub}$- $V_{G}$ and $\Delta$ $I_{ㅇ}$ measurement data show that MOSFETs with narrow channel-width are more susceptible to the hot-carrier degradation than MOSFETs with wide channel-width. By analysing $I_{sub}$/ $I_{D}$, linear $I_{D}$- $V_{G}$ characteristics, thicker oxide-thickness at the STI edge is identified as the reason for the channel-width dependent hot-carrier degradation. Using the charge-pumping method, $N_{it}$ generation due to the drain avalanche hot-carrier (DAHC) and channel hot-electron (CHE) stress are compared. are compared.