• Journal of the korean academy of Pediatric Dentistry
• /
• v.23 no.3
• /
• pp.640-658
• /
• 1996

The purpose of this study was to examine the mechanism of improving acid resistance of Nd-YAG laser irradiated tooth enamel and determine the most effective energy density for improving acid resistance. The bovine tooth enamel were lased with a pulsed Nd-YAG laser. The energy densities of exposed laser beam were varied from 10 to $70\;J/cm^2$. To investigate the degree of improving acid resistance by irradiation, all the samples were submerged to demineralize in 0.5 N $HClO_4$ solution for 1 minute. After 1 minute, 0.05 % $LaCl_3$ was added to the solution for interrupting the demineralization reaction. The amounts of dissolved calcium and phosphate in the solution were measured by using an atomic absorption spectrophotometer and the UV/VIS spectrophotometer, respectively. To examine the mechanism of improving acid resistance, X-ray diffraction analysis, infrared spectroscopy, and scanning electron microscopy were taken. The X-ray diffraction pattern of the samples were obtained in the $10^{\circ}{\sim}80^{\circ}2{\theta}$ range with $Cu-K{\alpha}$ radiation using M18HF(Mac Science Co.) with X-ray diffractometer operating at 40 KV and 300 mA. The infra-red spectra of the ground samples in 300 mg KBr pellets 10 mm diameter were obtained in the $4000cm^{-1}\;to\;400cm^{-1}$ range using JASCO 300E spectrophotometer. The scanning electron microscopy was carried out using JSM6400(JEOL Co.) with $500{\sim}2000$ times magnification. The results were as follow 1. The concentration of calcium dissolved from laser irradiated enamel with $50J/cm^2$ was significantly lesser than that of unlased control group (p<0.05) 2. From the result of the X-ray diffraction analysis, $\beta$-TCP, which increases acid solubility, was identified in lased enamel but the diffraction peaks of (002) and (004) became sharp with increasing energy density of laser irradiation. This means that the crystals in lased samples were grown through the c-axis and subsequently, the acid solubility of enamel decreased. 3. The a-axis parameter was slightly increased by laser irradiation, whereas the c-axis parameter was almost constant except for a little decrease at $50J/cm^2$. 4. In the infra-red spectra of lased enamels, phosphate bands ($600{\sim}500cm^{-1}$), B-carbonate bands (870, $1415{\sim}1455cm^{-1}$), and A-carbonate band ($1545cm^{-1}$) were observed. The amounts of phosphate bands and the B-carbonate bands were reduced, on the other hand, the amount of the A-carbonate band was increased by increase the energy density. 5. The SEM experiments reveal that the surface melting and recrystallization were appeared at $30J/cm^2$ and the cracks were observed at $70J/cm^2$. From above results, It may be suggested that the most effective energy density for improving acid resistance of tooth enamel with the irradiation of Nd-YAG laser was $50J/cm^2$. The mechanism of improving acid resistance were reduction of permeability due to surface melting and recrystallization of lased enamel and reduction of acid solubility of enamel due to decrease of carbonate content and growth of crystal.

• Bulletin of the Korean Chemical Society
• /
• v.16 no.7
• /
• pp.654-657
• /
• 1995

A series of excitation spectra (7Fo→5Do transition) of Eu(Ⅲ) ion in aqueous solution ([Eu(Ⅲ)]=1.12 × 10-2 mol L-1; pH 1.0 to 7.0) were obtained under CO2 free atmosphere using a pulsed tunable dye laser system. The broad and low intensity spectra (peak maximum: 578.89 nm) showed that the trivalent ion (Eu3+) underwent a low degree of hydrolysis at pH below 6.0. Eu(Ⅲ) hydroxo complex formation seemed more significant at pH above 6.0, shown by the occurrence of intense new peak at 578.63 nm. The spectra of those solutions prepared in N2 atmosphere showed no signs of the presence of interfering carbonate species. The Eu(Ⅲ) hydroxo complex formation was not observed when complexation studies between Eu(Ⅲ) ion and weak organic acids (e.g. glutarate and diglycolate) were conducted at pH 6.0 or below.

• Progress in Superconductivity and Cryogenics
• /
• v.11 no.2
• /
• pp.1-6
• /
• 2009

We report a successful fabrication of $high-J_c\;NdBa_2Cu_3O_{7-{\delta}}$ (NdBCO) films on $SrTiO_3$(STO) (100) substrates by pulsed laser deposition (PLD) in a relatively wide processing window. Under various oxygen pressures controlled by either 1%$O_2$/Ar mixture gas or pure $O_2$ gas, strongly c-axis oriented NdBCO films were grown at the substrate temperature $(T_s)\;of\;800^{\circ}C$ in 800 mTorr with 1%$O_2$/Ar gas and also in 400 and 800 mTorr with pure $O_2$ gas. These samples exhibited $T_c$ values over 90K and $J_c$ values of $2.8-3.5MA/cm^2$ at 77K in self-field (77K, sf). On the other hand, $J_c$ values over $1A/cm^2$ were obtained at the temperature regions of $700-830^{\circ}C$ in 800 mTorr with 1%$O_2$/Ar gas at those of $750-830^{\circ}C$ in 800 mTorr with pure $O_2$ gas. Unlike previous reports, resent results support that the PLD processing window for high-Jc NdBCO films is not narrow.

• Transactions on Electrical and Electronic Materials
• /
• v.7 no.3
• /
• pp.149-153
• /
• 2006

An attempting to produce a p-type diluted magnetic semiconductor (DMS) using $Ti_{1-x}Co_xO_{2-\delta}-based$ thin films was made by suitable control of the deposition parameters including deposition temperature, deposition pressure, and doping level using a pulsed laser deposition method. T$Ti_{0.97}Co_{0.03}O_{2-\delta}-based$ (TCO) films deposited at $500^{\circ}C$ at a pressure of $5\times10^{-6}$ Torr showed an anomalous Hall effect with p-type characteristics. On the other hand, films deposited at $700^{\circ}C$ at $5\times10^{-6}$ Torr showed n-type behaviors by a decreased solubility of cobalt. The charge carrier concentration in the p-type TCO films was approximately $7.9\times10^{22}/cm^3$ at 300 K and the anomalous Hall effect in the p-type TCO films was controlled by a side-jump scattering mechanism. The magnetoresistance (MR), measured at 5 K in p-type TCO films showed a positive behavior in an applied magnetic field and the MR ratio was approximately 3.5 %. The successful preparation of p-type DMS using the TCO films has the potential for use in magnetic tunneling junction devices.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.668-668
• /
• 2013

CIGS 박막태양전지는 다른 박막태양전지에 비해 높은 에너지 변환효율을 보이고 있으며, 광범위한 기술 응용분야를 가지고 있다. CIGS를 광흡수층으로 하는 태양전지의 구조는 5개의 단위박막(배면전극, 광흡수층, 버퍼층, 앞면 투명전극, 반사방지막)을 순차적으로 형성시켜 만든다. 단위박막별로 다양한 종류의 재료와 조성, 또한 제조방법에서는 갖가지 물리적, 화학적 박막 제조방법이 사용된다. 현재 광흡수층인 CIGS층의 경우 동시증발법과 스퍼터링법이 높은 효율을 보이고 있다. 본 연구에서는 CIGS층을 3-stage process를 적용한 동시증발법을 사용하였고, Fluxmeter와 기판후면 온도 모니터링을 이용하여 제조하였으며, 버퍼층은 moving 스퍼터링 법으로 ZnS를 증착하였고, 투명전극층은 PLD (Pulsed Laser Deposition)를 이용하여 제조하였다. 가장 높은 광변환효율을 보인 Al/ZnO/CdS/Mo/SLG박막시료는 유효면적 0.45 $cm^2$에 광변환효율 15.71%, Jsc: 33.64 mA/$cm^2$, Voc: 0.64 V, FF: 73.18%를 얻을 수 있었으며, CdS를 ZnS로 대체한 Al/ZnO/ZnS/Mo/SLG 박막시료는 유효면적 0.45 $cm^2$에 광변환효율 12.13%, Jsc: 33.22 mA/$cm^2$, Voc: 0.60 V, FF: 62.85%를 얻을 수 있었다.

• Progress in Superconductivity and Cryogenics
• /
• v.10 no.2
• /
• pp.16-19
• /
• 2008

Angular dependence of critical current density of SmBCO coated conductor fabricated by co-evaporation method was investigated. For comparison, three samples were fabricated by a co-evaporation method and one sample was fabricated by a pulsed laser deposition process. The deposition system, named EDDC (Evaporation using Drum in Dual Chambers), is a batch type co-evaporation system, which is composed of reaction chamber and evaporation chamber. The normalized critical current density ratio ($I_c/I_c$(H//ab-plane)) of EDDC-SmBCO samples was found to be higher than that of PLD-YBCO sample in the whole range of angle. While the EDDC-SmBCO samples evidently had a peak at the angle of H//c-axis in the plot of the angular dependence of critical current, the normalized critical current of PLD-YBCO sample decreased monotonically without any peak as angle increased. The field dependence of critical current under the magnetic field parallel to the normal direction of those samples showed similar aspect in the range of $0\;G{\sim}5000\;G$.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.02a
• /
• pp.371-372
• /
• 2012

We have studied lead-based gapless semiconductors, $PbPdO_2$, which is very sensitive to external parameters such as temperature, pressure, electric field, etc[1]. We have fabricated pure $PbPdO_2$, Co- and Mn-doped $PbPdO_2$ thin films using the pulsed laser deposition. Because of the volatile element of Pb, it is very difficult to grow the films. Note that in case of $MgB_2$, Mg is also volatile element. So in order to enhance the quality of $MgB_2$, some experiments are carried out in annealing with Mg-rich atmosphere [2]. This annealing process with volatile element plays an important role in making smooth surface. Thus, we applied such process to our studies of $PbPdO_2$ thin films. As a result, we found the optimal condition of ex-situ annealing temperature ${\sim}650^{\circ}C$ and time ~12 hrs. The ex-situ annealing brought the extreme change of surface morphology of thin films. After ex-situ annealing with PbO-rich atmosphere, the grain size of thin film was almost 100 times enlarged for all the thin films and also the PbO impurity phase was smeared out. And from X-ray diffraction measurements, we determined highly crystallized phases after annealing. So, we measured electrical and magnetic properties. Because of reduced grain boundary, the resistivity of ex-situ annealed samples changed smaller than no ex-situ sample. And the carrier densities of thin films were decreased with ex-situ annealing time. In this case, oxygen vacancies were removed by ex-situ annealing. Furthermore, we will discuss the transport and magnetic properties in pure $PbPdO_2$, Co- and Mn-doped $PbPdO_2$ thin films in detail.

• Journal of Sensor Science and Technology
• /
• v.15 no.1
• /
• pp.65-70
• /
• 2006

Characteristics of thin-film NTC thermal sensors fabricated by micromachining technology were studied as a function of the thickness of membrane. The overall-structure of thermal sensor has a form of Au/Ti/NTC/$SiO_{X}$/(100)Si. NTC film of $Mn_{1.5}CoNi_{0.5}O_{4}$ with 0.5 mm in thickness was deposited on $SiO_{X}$ layer (1.2 mm) by PLD (pulsed laser deposition) and annealed at 873-1073 K in air for 1 hour. Au(200 nm)/Ti(100 nm) electrode was coated on NTC film by dc sputtering. By the results of microstructure, X-ray and NTC analysis, post-annealed NTC films at 973 K for 1 hour showed the best characteristics as NTC thermal sensing film. In order to reduce the thermal mass and thermal time constant of sensor, the sensing element was built-up on a thin membrane with the thickness of 20-65 mm. Sensors with thin sensing membrane showed the good detecting characteristics.

• Progress in Superconductivity and Cryogenics
• /
• v.16 no.2
• /
• pp.1-6
• /
• 2014

The five-year national project in Japan for R&D of coated conductors and applications, named as the Materials and Power Applications of Coated Conductors (M-PACC) project, was finished at the end of FY2013. The project consists of four sub-themes as cable, transformer, SMES and coated conductors. In the theme of coated conductors, the fabrication process had been developed to satisfy the requirements from the applications such as in-field $I_c$ performance, low AC loss in the long tapes etc. Through the project, the remarkable progress was achieved as follows; a high in-field minimum $I_c$ value over 54A/cm-width under 3T at 77K was realized in a 200m long EuBCO tape with artificial pinning centers of $BaHfO_3$ by the pulsed laser deposition (PLD) technique on the IBAD template. On the other hand, the AC loss reduction was confirmed in the tapes fabricated by both PLD and the metal organic deposition (MOD) techniques by scribing 100m tapes into 10-filamments. Additionally, the mechanism of the delamination phenomenon was systematically investigated and the strength was improved by eliminating the origins of the weak points in the films. Through the development, all targeted goals were accomplished and the several results were appreciated as a world champion data.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2003.11a
• /
• pp.56-56
• /
• 2003

BaTiO$_3$, SrTiO$_3$단일막과 BaTiO$_3$ (BTO)/SrTiO$_3$ (STO) 산화물 인공격자를 pulsed laser deposition (PLD) 법에 의해서 100 nm 두께의 (La,Sr)CoO3 (LSCO) 산화물 전극이 코핑된 MgO 단결정 기판 위에 증착시켰다. 이러한 기판위에서 2 unit cell의 적층 두께를 갖는 BTO/STO 초격자 (=BTO2/STO2)를 100～5 nm까지 변화시켰다. 또한 BTO와 STO 단일막도 같은 두께로 변화시켰다. 이러한 두께 범위에서 BTO, STO 단일막과 초격자의 격자변형에 따른 유전특성을 살펴 보았다. 두께 변화에 따른 단일막과 초격자의 구조 분석은 포항 방사광 가속기의 x-ray 회절에 의해서 이루어졌다. 다양한 두께를 갖는 BTO2/STO2 초격자에서 BTO와 STO 충은 in-plane 방향으로 격자정합을 유지하면서 변형되었다. 두께가 얇아지면서 하부 LSCO영향으로 BTO, STO의 n-plane 격자상수는 LSCO 격자상수 쪽으로 접근하였다. Out-of-plane 방향의 BTO 격자상수는 두께가 얇아지면서 증가하였고 반면에 STO 격자상수는 감소하였다. STO와 BTO 단일막의 격자변형은 두께가 얇아지면서 in-plane 방향으로 압축응력으로 인해 증가하였다. 그러나, 격자부정합도가 큰 BTO격자에서 더 많이 변형되었다. 또한 초격자에서 BTO격자가 BTO 단일막보다 더 많이 변형되었는데 초격자에서는 BTO, STO 두 층의 발달된 변형뿐만 아니라 하부 LSCO/MgO 기판의 영향을 함께 받고 있기 때문이다. 초격자와 단일막의 유전상수를 살펴보면은 두께가 감소하면서 유전상수가 감소하는 size effect을 보이고 있다. 하지만 초격자에서의 유전상수가 단일막보다 우수한 유전특성을 보이고 있다. 이러한 결과로 볼 때 격자변형이 size effect 영향을 끼치는 중요한 요소임을 확인하였다.