• Proceedings of the KIPE Conference
• /
• 2002.11a
• /
• pp.25-28
• /
• 2002

In this paper, 2 phase modulated SRPP-PWM(Separately Random Pulse Position PWM) is proposed. This PWM technique is based on the 2 phase modulated SVPWM(Space Vector Pulse Width Modulation). In according to the theory of SVPWM, 2 phase modulated SVPWM uses two pulses, not three pulses as in 3 phase modulated SVPWM. In the proposed SRPP-PWM scheme, each of two phase pulses is located randomly in each switching interval. The experimental results show that the voltage and switching noise harmonics are spread to a wide band area. Also, the performance of the proposed 2 phase modulated SRPP-PWM and the conventional SVPWM are compared to each other In result, the speed response is nearly similar to each other from the viewpoint of the v/f constant control.

• Proceedings of the KIEE Conference
• /
• 2005.07b
• /
• pp.1503-1505
• /
• 2005

The Cold cathode fluorescent lamp(CCFL) are widely used to illuminate the liquid crystal display(LCD). Ballasts are required for CCFL because the lamp need high starting voltage and behave negative dynamic resistant characteristics in the desired region of operation. Dimming methods of CCFL are used to pulse frequency modulation(PFM) or pulse width modulation(PWM). In this paper, CCFL driving and control circuit is designed by half-bridge type series and parallel resonant inverter that variable frequency modulation method to control the output voltage current. The validity of this study is confirmed from the simulation and experimental results.

• Journal of Power Electronics
• /
• v.18 no.6
• /
• pp.1627-1633
• /
• 2018

A constant voltage AC-DC converter based on digital assistant technology is proposed in this paper, which has rapid dynamic response capability. The converter operates in the PFM (Pulse Frequency Modulation) mode. According to the load state, the compensation current produced by the digital compensation module was injected into the CS pin to adjust the switching pulse width dynamically and improve the dynamic response. The control chip is implemented based on NEC $1{\mu}m$ 5V/40V HVCMOS process. A 5V/1.2A prototype has been built to verify the proposed control method. When the load jumps from idle to heavy, the undershoot time is only 7.4ms.

• Journal of IKEEE
• /
• v.17 no.3
• /
• pp.267-274
• /
• 2013

This paper presents a design of LLC resonant converter IC for LED backlight unit based on PFM/PWM dual-mode feedback. Dual output LLC resonant architecture with a single inductor is proposed, where the master output is controlled by the PFM and slave output is controlled by the PWM. To regulate the master output PFM is used as feedback to control the frequency of the power switch. On the other hand, PWM feedback is used to control the pulse width of the power switch and to regulate the slave output. This chip is fabricated in 0.35um 2P3M BC(Bipolar-CMOS-DMOS) Process and the die area is $2.3mm{\times}2.2mm$. Current consumptions is 26mA from 5V supply.

• Journal of Welding and Joining
• /
• v.29 no.3
• /
• pp.82-88
• /
• 2011

With a tendency for the application of thin magnesium alloy plates in portable electronic equipment such as cell phone and notebook PC, there is a requirement to develop a welding technology for the lap welding of these thin magnesium alloy. This paper presents the single pulsed laser welding of AZ31B magnesium alloy. The effects of fiber types and parameters such as peak power and pulse width on laser weldability were investigated. The results show that weld defects, especially solidification crack, were always generated in the weld. These defects couldn't be controlled by the simple square pulse, but could be improved through the application of variable pulse. It is because that variable pulse has effect of solidification delay by dropping peak power gradually.

• Journal of Institute of Control, Robotics and Systems
• /
• v.9 no.1
• /
• pp.10-21
• /
• 2003

During seek operation in disk drives, the recording head is moved toward desired track by seek servo controller and then is settled onto the center of the desired track by settling servo controller. If the head speed at the start of settling servo control is not slow, it may produce overshoot relative to the center of track and thus extend the settling time. The degradation in settling performance will be more severe as the track width becomes smaller for higher density of data storage. We design a new settling servo controller for minimizing settling time based on the pole-zero cancellation. In order to cancel slow poles in settling response, we apply discrete pulse signals to the system in addition to the state feedback control. For exact pole-zero cancellation, we consider the dynamics of power amplifier used for actuator current regulation and the effects of delay in control action. In addition, we present system parameter identification algerian for the robustness of our controller to system parameter variation. In order to demonstrate the practical use of our controller, we present experimental results obtained by using a commercially available disk drive.

• Journal of Advanced Navigation Technology
• /
• v.21 no.4
• /
• pp.377-385
• /
• 2017

The solar cell need the characteristic interpreting because the solar cell changes greatly according to the isolation, temperature and load in the photovoltaic development. Moreover, to get many energy in photovoltaic development need the position tracking of the sun according to the environment change. Also, The solar cells should be operated at the maximum power point. In this paper, I used microprocessor and sensor and designed to improve the efficiency of the photovoltaic system the photovoltaic position tracker device, and compared the normal photovoltaic system of fixed form with the photovoltaic system of solar position tracked form. Moreover, compared the catalogue of solar cell module and the simulation through a mathematics modelling with the solar cell's characteristic interpreting and composed an power conversion system with boost converter and voltage source inverter. Used the constant voltage control method for maximum power point tracking in boost converter control and, used the SPWM(Sinusoidal Pulse Width Modulation) control method in inverter control. The result was less then 5% when compared the catalogue of solar cell module and the simulation through a mathematics modelling. The boost rate of boost converter was similar to 167 % with the simulation.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.9 no.3
• /
• pp.1-8
• /
• 1972

The characteristics of tunnel diode pair circuit biased within the negative resistance region has also the voltage-control type negative resistance region, and the voltage at the center point of negative resistance region is described as the square-wave relaxation oscillation. In this paper, the period T, positive duration T1, negative duration T2 of the pulse are obatined from the characteristic curve T, positive duration T1, negative duration T2 of the pulse are obtained from the characteristic curve and observed actually, considring the fact that the pulse width and the period of square-wave at the center point of the negative resistance region is able to be controlle dby the blas volgate. Mereover, the relationship between T, T1 or T2 and circuit parameters is searched for and the Circuit parameters that satisfy the conditions of T1-T2 being proportional to the variation of bias voltage with Teonstant are determined. Thereafter, the bias voltage and the signal voltage are inserted serially to the PWM circuit and the characteristics of that circuit is analyzed.

• The Proceedings of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.2 no.2
• /
• pp.59-63
• /
• 1988

In a fixed AC power source the PWM techniques were used to vary the voltage and the fundamental frequency. The conventional PWM techniques due to the problem of commutation number and filter size have been studied the PWM output waveforms which applied the motor drive. However in this paper, the carrier frequency with sinusoidal PWM waveform is modulated from 10(KHz) to 45(KHz) using termination devices with high - speed switching capacity and applying LPF(Low Pass Filter) with small capacity to output of inverter and the PAM(Pulse Amplitude Modulation)is obtained. Considering the property of the speed and the control, the sinusoidal PWM control circuit was composed of the microprocessor and analog circuit. In experment result, the system properties are study on the sinusoidal voltage waveform with modulation index changing from 0.6 to 1.0.

• Proceedings of the KIEE Conference
• /
• 2000.07c
• /
• pp.2107-2109
• /
• 2000

A pulsed Nd:YAG laser is used widely for materials processing and medical instrument. It's very important to control the laser energy density in those fields using a pulsed Nd:YAG laser. A pulse repetition rate and a pulse width are regarded as the most dominant factors to control the energy density of laser beam. In this paper, the alternating charge and discharge system was designed to adjust a pulse repetition rate This system is controlled by microprocessor and allows to replace an expensive condenser for high frequency to cheap one for low frequency. In addition, The microcontroller monitors the flow of cooling water, short circuit. and miss firing and so on. We designed Nd:YAG laser firmware with smart microcontroller, and want to explain general matters about the firmware from now.