• Progress in Superconductivity and Cryogenics
• /
• v.3 no.1
• /
• pp.45-49
• /
• 2001

A magnet supporting post installed between the lower TF coil tooled by 4.5 K supercritical helium and the cryostat base is one of the most important components of the superconducting magnet supporting structure for KSTAR Tokamak. This structure should be flexible to absorb thermal shrink of the magnet and also should be rigid to support the magnet weight and the Plasma disruptions load. The Post was designed with stainless steel 316LN and CFRP that have low thermal conductivity and high structural strength at low temperature. In order to verify the possibility of fabrication and the structural safety. a whole scale prototype of the KSTAR magnet supporting post was manufactured and tested. Static and compressive cyclic load tests under the maximum Plasma vertical disruption load and the magnet dead weight were performed. The teat results showed that the magnet supporting post of KSTAR Tokamak was possible to manufacture and structurally rigid.

• 유체기계공업학회:학술대회논문집
• /
• 2002.12a
• /
• pp.307-313
• /
• 2002

In the paper, the prototype development of a 75kW class microturbine for the distributed generation market is partly presented which has continued with the government funding. In the introduction, an overview of the development of microturbines in the world is presented. A series of development procedures are shown with design, manufacture and self-sustaining tests. During the first year, aerodynamic and structural design/analysis, mechanical design are performed for the compressor, the turbine and the combustor. A premixed lean burn combustor technology is used fur the low emission requirements. Foil air bearings and high-speed motors are employed for higher reliability. The self-sustaining conditions have been successfully achieved with the prototype manufactured engine as a preceding operation.

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• 2000.06a
• /
• pp.93-105
• /
• 2000

This paper describes prototype Virtual Reality Ship Simulator (VRSS) that we have recently developed next-generation training equipment based on the virtual reality (VR) technology. The inherent defects of conventional ship simulators are enormous costs and difficult system upgrade due to the system construction, such as large mock-up bridge system, wide visual presentations, In this paper, to cope with those problems, we explored VR technology that can give realistic environments in a virtual world. Then we constructed prototype VRSS system, which is, consists of PC-based human sensors, and Databases set having 3D object models and coefficients of Head Related Transfer Functions (HRTFs). 3D-WEBMASTER authoring tool was used as Virtual Reality Modeling Language (VRML). Using the VRSS system, we constructed Port an Passage Simulator for the harbor of INCHON in Korea, and Ship and Sea State Simulator for an arbitrary given sea environmental states by user. Through many simulation tests, we testified the efficiency of developed prototype VRSS by subject assessment with five participants. Then, we present results on the simulation experiments and conclude with discussion of evaluation results.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1995.10a
• /
• pp.198-203
• /
• 1995

The objective of this study is to provide the information on the techniques of manufacturing and experiment in small scale modeling of precast concrete(P.C.)large panel structures. The adopted scale was 1/5th 4types of experiments were performed : material tests for model concrete and model reinforcement, compressive test of horizontal joint, shear test of vertical joint and cyclic static test of 2-story subassemblage structure. Based on the experimental results, the following conclusions are drawn: (1)Model concrete may have in general larger compressive strength than expected. (2) Model reinforcement can show less ductility if the annealing processes were performed without using vaccuum tube. (3) Failure modes of horizontal and vertical joints were almost same for both prototype and model. But the strength of model appears to be higher than required by similitude law. (4)Hysteretic behavior of 1/5 scale subassemblage model can be made quite similar to prototype's if the ductility of model reinforcement and compressive strength of model concrete could be representative of those of prototype.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.25 no.5
• /
• pp.856-867
• /
• 2001

The purpose of this study was to develop washable panties for elderly women of incontinence urine. We carried out a questionnaire survey in order to find out what are the inconvenience of incontinence. Also we analyse the properties of incontinence panties available in silver market. Then we did wearing test of the existing continence panties to 40 subjects. Having done the wearing test, it was clear that the composit and the size of the absorbing layers must be crucial points of the development of the prototype panty. The prototype was designed to improve absorbing speed as well as capability without sacrificing of wearing comfort. The developed prototype panty went through wearing test and property tests to assure the design. The results are as follows:- 1. Absorbing capability as a whole, quick absorbance at the moment of passing of urine, the touch of the cover layer after quick absorbance and deodorant property were improved than existing incontinence panties. 2. The size and the dimensions of each part, specially absorbing layers at the crotch area, were remarkably improved.

• Proceedings of the Korea Institute of Applied Superconductivity and Cryogenics Conference
• /
• 2003.02a
• /
• pp.213-215
• /
• 2003

This paper deals with the characteristics of a prototype solenoid for basic design of DC reactor type superconducting fault current limiter (SFCL). The prototype high-Tc Super-conducting (HTS) solenoid was manufactured with 4 stacked Bi-2223 tape. The critical currents were measured with respect to the number of stacks. In order to test the safety of HTS solenoid in quenched state, the transport tests of AC over-current were performed. These experimental results could be applied to the basic design of HTS DC reactor for SFCL effectively.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2006.10a
• /
• pp.241-255
• /
• 2006

Owing to a landslide or embankment damage be caused by a localized torrential downpour and heavy snowfall resulted from recent abnormal climate, a slope stability is very important. This study is investigate a general slope reinforcement method and applicability improvement of soil nailing method utilized prototype loading test for the facing stiffness effect confirmation. A prototype loading test supplements general slope stability study by numerical analysis or laboratory test with a resonable analysis of slope structure.

• Journal of the Korea Society of Computer and Information
• /
• v.21 no.9
• /
• pp.19-25
• /
• 2016

This paper is to recognize and play tab chords from guitar musical sheets. The musical chord area of an input image is segmented by changing the image in saturation and applying the Grabcut algorithm. Based on a template matching, our approach detects tab starting sections on a segmented musical area. The virtual block method is introduced to search blanks over chord lines and extract tab fret segments, which doesn't cause the computation loss to remove tab lines. In the experimental tests, the prototype based classification outperforms Bayesian method and the nearest neighbor rule with the whole set of training data and its performance is similar to that of the support vector machine. The experimental result shows that the prediction rate is about 99.0% and the number of selected prototypes is below 3.0%.

• Proceedings of the KSR Conference
• /
• 1999.11a
• /
• pp.189-201
• /
• 1999

According to the current trend of single arm type pantograph for high speed trail korean pantograph designed to single arm type will be installed on each power car roof of prototype train of korean very high speed rail configured to 7 cars and have the characteristics of maximum 1% contact loss at 350 km/h speed. This study is devoted to design basically element components of pantograph for korean very high speed train on the basis of kinematic analysis, static analysis and dynamic analysis, followed by making the basic drawings of korean pantograph. This drawings will be complemented through certification tests of prototype pantograph and verification of analysis software.

• Aerospace Engineering and Technology
• /
• v.4 no.2
• /
• pp.50-59
• /
• 2005

This paper described performance test of 1st prototype "Tail-Fan" system. KARI(Korea Aerospace Research Institute) developed "Tail-Fan" system as a kind of helicopter anti-torque system(ATS) and designed ATS performance test-rig for Tail-Fan system performance test. For Tail-Fan system performance tests, firstly, test-rig operation tests were carried out for verification of design specifications. And natural frequencies of fan blade and test-rig were measured respectively. To find the operation rotating speed for performance tests, vibration tests using accelerometers on tail gear box(TGB) were carried out. Through the fanplot and vibration test results, rotational speed for Tail-Fan performance test to avoid a resonance were found and performance tests were carried out in flight conditions. We analyzed test data by non-dimensionalization. Through this results, 1st prototype "Tail-Fan" system was satisfied with design requirements.