• Proceedings of the Korean Institute of Intelligent Systems Conference
• /
• 1993.06a
• /
• pp.1266-1269
• /
• 1993

The paper introduces a new method for fuzzy processing. The method allows handing a piece of information lost in the classic fuzzification process, and thus neglected by other methods. Processing the result after fuzzification is sustained by the interpretation that the input-output set mapping, specified by the IF-THEN rules, can be regarded as a direct mapping of their corresponding alpha-cuts. Processing involves just singletons as intermediary results, the final result being a combination of singletons obtained from fired rules.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.55 no.2
• /
• pp.218-223
• /
• 2022

Cholesterol is an essential component for maintaining health; however, excessive consumption can lead to diseases. Thus, continuous monitoring of cholesterol content is important in food research. The cholesterol analysis method used in Korea follows the Korean Food Standards Codex. As this method uses gas chromatography, derivatization of the sample is required, and analysis time is more than 30 min. Kim developed a new method using liquid chromatography; however saponification by the non-heat saponification method is insufficient. To address these limitations, a new cholesterol analysis method was developed and verified. The correlation coefficients for the cholesterol standard (STD) were maintained above 0.99. The limit of detection and limit of quantitation of cholesterol STD were 2.41 ㎍/mL and 7.31 ㎍/mL, respectively. The accuracies for cholesterol were 92.21-99.02%. The developed analytical method was also verified using three standard reference materials, and their accuracies were 93.71-97.09%. In addition, the cholesterol content of fishes was analyzed, and the values were compared with those recorded by the United States Department of Agriculture. Our results suggest that this method could be used as a new analytical method for cholesterol in seafood.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2010.10a
• /
• pp.527-532
• /
• 2010

This paper is concerned with the measurement of static and dynamic displacement by image processing(IP) and study for prediction method of velocity and acceleration. To measure the displacement visually, the measurement system consists of a telephoto zoom camera, ccd image device and a computer. The specific target on the white board is used to calculate the displacement of the structure. The captured image is then converted into a pixel-based data and then analyzed numerically. The limitation of the system depends on the image capturing speed and the pixel-size of image. In this paper, we developed for the displacement measurement using the image processing method. The proposed method enables us to measure the vibration measurement, velocity and acceleration directly without any contact. The current resolution of the displacement measurement is limited to 1/100 millimeter scale.

• Journal of the Institute of Convergence Signal Processing
• /
• v.16 no.3
• /
• pp.83-89
• /
• 2015

Connected component labeling (CCL) is a mandatory step in image segmentation where objects are extracted and uniquely labeled. CCL is a computationally expensive operation and thus is often done in parallel processing framework to reduce execution time. Various parallel CCL methods have been proposed in the literature. Among them are NSZ label equivalence (NSZ-LE) method, modified 8 directional label selection (M8DLS) method, HYBRID1 method, and HYBRID2 method. Soh et al. showed that HYBRID2 outperforms the others and is the best so far. In this paper we propose a new hybrid parallel CCL algorithm termed as HYBRID3 that combines selective four directional label search (S4DLS) with label backtracking (LB). We show that the average percentage speedup of the proposed over M8DLS is around 60% more than that of HYBRID2 over M8DLS for various kinds of images.

• Journal of Korean Society of Industrial and Systems Engineering
• /
• v.20 no.41
• /
• pp.231-242
• /
• 1997

This paper describe an approximation method for solving the minimum makespan problem of job shop scheduling with fuzzy processing time. We consider the multi-part production scheduling problem in a job shop scheduling. The job shop scheduling problem is a complex system and a NP-hard problem. The problem is more complex if the processing time is imprecision. The Fuzzy set theory can be useful in modeling and solving scheduling problems with uncertain processing times. Lee-Li fuzzy number comparison method will be used to compare processing times that evaluated under fuzziness. This study propose heuristic algorithm solving the job shop scheduling problem under fuzzy environment. In This study the proposed algorithm is designed to treat opinions of experts, also can be used to solve a job shop environment under the existence of alternate operations. On the basis of the proposed method, an example is presented.

• Proceedings of the Korean Institute of IIIuminating and Electrical Installation Engineers Conference
• /
• 2004.11a
• /
• pp.359-364
• /
• 2004

This paper deals with the comparison of signal processing techniques of ultrasonic data. The goal of signal processing is the ultrasonic speckle suppression and the visibility enhancement of flaw-reflected ultrasonic echo. The performance of conventional SSP(split spectrum processing) method and the wavelet denoising method are compared and discussed for tested ultrasonic data. Tested ultrasonic data obtained from the weld area of centrifugal-casted stainless steel material and safe-ending material with holes and notch of variable depths are presented. In experimental results, the outputs of wavelet-based denoising method show the clear and sharp peaks at the positions of flaw-reflected echos comparing with those of SSP method.

• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.37 no.11
• /
• pp.804-815
• /
• 1988

Real-time image processing algorithms to detect position and orientation of rectangular type electronic components are developed. The position detection algorithm is implemented with the use of projection method which is insensitive to noise. Also dynamic thresholding method of projection is employed in order to distinguish between the boundary of a component and any marking on the component. The orientation is determined by Hough transform of boundary candidates of a component, which is obtained a priori by a simple edge detection method. For real-time processing of both position and orientation for a component which is not aligned well, parallel processing method of image data is proposed and tested in real-time.

• Journal of the Korean Institute of Telematics and Electronics B
• /
• v.33B no.12
• /
• pp.31-44
• /
• 1996

Since optical delay line signal processing which utilizes optical fiber as delay line elements can provide high speed and broadband signal processing, the optical delay line signal processing has numerous applications. Recently, many research papers which optical delay line signal processing techniques are being applied to OCDMA are published. The author has published paper on the design method for optical fiber filters of lattice structure. However, the previous design method does not realize the transfer function all the time. It can be realized with constraints. In this paper, we propose the design method that can realize the transfer function all the time without any constraints for the optical fiber filter of lattice structure.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2003.06a
• /
• pp.1046-1050
• /
• 2003

In this paper, we describe study on the development or multi-path ultrasonic gas flowmeter using a transit time method. This system includes 5 pairs of ultrasonic transducers. ultrasonic signal processing unit using switch matrix method, computation algorithm of gas flow rate, spool piece type multi-path pipe unit. We have developed enhanced type of main ultrasonic signal processing unit using switch matrix method fer multi-path ultrasonic gas flowmeter. Also, we have developed the new transmitting ＆ receiving method of ultrasonic waves and the new signal processing algorithm for the computation of ultrasonic transit time from received ultrasonic waves. In this study, we have designed more compact signal processing unit compared with the conventional hardware system of multi-path ultrasonic gas flowmeter. We have confirmed its reliability for multi-path ultrasonic gas flowmeter through the laboratory test using calibration system. In the future. we will perform the field test for the developed system in the POSCO gas line.

• Journal of the Society of Naval Architects of Korea
• /
• v.52 no.5
• /
• pp.365-371
• /
• 2015

Hull plate consists of various types of curved plates and there also exists corresponding processing methods. Typically, curved plates can be divided into convex type and saddle type. Large amount of research has been conducted mainly focusing on application of processing method of convex type, saddle type and hybrid type, but research on determination and processing method application of the most difficult S-shaped curved plate that has inflection lines has not been carried out yet. In this paper, as the fundamental research of appropriate processing method application, a calculation method is proposed to calculate inflection lines on curved plates. In order to calculate inflection lines, normal curvature and information of fabricated curved plates should be utilized. We compare the workability of the fabrication for hull plate using inflection line.