• Transactions on Electrical and Electronic Materials
• /
• v.3 no.1
• /
• pp.1-3
• /
• 2002

A p-n junction was obtained by the deposition of an n-type ZnO thin film on a p-type Zn-doped InP substrate. The Zn-doped InP substrate has been made by the diffusion of Zn with sealed ampoule technique. The ZnO deposition process was performed by pulsed laser deposition (PLD). The p-n junction was formed and showed typical I-V characteristics. We will also discuss about the realization of an ultraviolet light-emitting diode (LED). The structure of n-ZnO/p-Zn-doped InP could be a good candidate for the realization of an ultraviolet light-emitting diode or an ultraviolet laser diode.

• Proceedings of the Safety Management and Science Conference
• /
• 2000.05a
• /
• pp.97-110
• /
• 2000

Production schedule and realization quantity of Large type bus [929(HD), 928, 928-A(SD), 937E/L, 937/L,] were analyzed in order to intruoduce FMS(Flexible Manufacturing System) appropriate for varities of customer desire and multi-item, small lot production. And this paper is aimed to propose introduction method of FMS, analyzing zig tools change times and idle times with production line and workers as an object. According to analysis results, only simple spec., depending on bus type, changed with decrease in production. For 929(HD), 928,928-A(SD), 937Eh, 937/L bus type, there was no harmony between schdule and realization. Therefore, it caused many difficulties in part supply. And there was loss of manpower and reduction of productibility due to idle time of process with bus type change. Production processes were operated inefficiently because tact time exceeded or shortaged of allow time.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.11b
• /
• pp.126-129
• /
• 2001

A p-n junction was obtained by the deposition of an n-type ZnO thin film on a p-type Zn-doped InP substrate. The Zn-doped InP substrate has been made by the diffusion of Zn with sealed ampoule technique. The ZnO deposition process was performed by pulsed laser deposition (PLD). The p-n junction was formed and showed a typical I-V characteristic. We will also discuss about the realization of an ultraviolet light-emitting diode (LED). The structure of n-ZnO/p-Zn-doped InP could be a good candidate for the realization of an ultraviolet light-emitting diode or an ultraviolet laser diode.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.11a
• /
• pp.126-129
• /
• 2001

A p-n junction was obtained by the deposition of an n-type ZnO thin film on a p-type Zn-doped InP substrate. The Zn-doped InP substrate has been made by the diffusion of Zn with sealed ampoule technique. The ZnO deposition process ws performed by pulsed laser deposition (PLD). The p-n junction was formed and showed a typical I-V characteristic. We will also discuss about the realization of an ultraviolet light-emitting diode (LED). The structure of n-ZnO/p-Zn-doped InP could be a good candidate for the realization of an ultraviolet light-emitting diode or an ultraviolet laser diode.

• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.41 no.8
• /
• pp.883-892
• /
• 1992

In order to remove the assumption of full state availability which is one of the major difficulties with the practical realization of variable structure control system (VSCS), an output feedback variable structure control scheme for multivariable systems is proposed. The proposed output feedback VSCS is composed of a switching surfaces with dynamic structure and a new output feedback control input that can be constructed by using conventional output feedback control input design methodologies. With the proposed scheme, the practical realization of VSCS for the systems with unmeasurable states and for high order systems that conventional schemes cannot be applied is possible. Simulation results show that proposed scheme is a viable method to achieve the desired control performance, for example, good transient response, robustness against process parameter variations and external disturbance without measuring all the state variables.

• Transactions of Materials Processing
• /
• v.17 no.5
• /
• pp.350-355
• /
• 2008

Currently, in the automotive industry, the efforts to reduce the manufacturing cost by changing the manufacturing process are continually performed. In this paper, we proposed a new manufacturing process, the roll bending process of a ring plate of automotive fuel tank instead of conventional press blanking process to reduce material loss and manufacturing cost. Finite element analysis was used to optimize the roll bending process to assure rectangular cross-section of the ring plate. Also, spring-back analysis after the roll bending process was performed and dimension of the bending die considering spring-back was analyzed. Finally, we verified a possibility for realization of the proposed method with prototypes.

• Proceedings of the KIEE Conference
• /
• 1988.07a
• /
• pp.161-164
• /
• 1988

The purpose of this paper is to propose a simple firmware realization of PCM framing system, which exploits LSI memories for performance improvement and hardware simplification. The proposed system simply consists of a tapped delay line for simultaneous observation of in framing-bits and ROM programmed sequence controller for framing process. Perpormance analyses are made in terms of misframe interval, sync-loss-detection time and reframe time. The proposed strategy proved to be significantly better in reframe time, stability and hardware implementation.

• Journal of the Korea Safety Management & Science
• /
• v.6 no.2
• /
• pp.167-178
• /
• 2004

Supply chain management and e-procurement system built in the company, are set goal of internal process improvement. This paper show how SLV(Supplier Lifetime Value) can be used to structure the supplier in automotive part manufacturer, the method of selection is described and a detailed example of how SLV can be used and allocation of order Quantity for the selected suppliers also are provided, and aims at giving a method to realization profitable supplier relation using search for SL V system development which is making corporation with supplier, in the favor of decision supplier.

• Proceedings of the KIEE Conference
• /
• 2007.07a
• /
• pp.640-641
• /
• 2007

In this paper, the discrete wavelet transform (DWT) was applied a fault detection of a synchronous generator being superior to a transient state signal analysis and being easy to real time realization. The fault signals after executing a terminal fault modeling collect using a MATLAB package, and calculate the wavelet coefficients through the process of a multi-level decomposition (MLD). The proposed algorithm of a fault detection of a generator using Daubechies WT (wavelet transform) was executed with a C language for the commend line function and for the real time realization after analyzing MATLAB's graphical interface.

• Korean Journal of Computational Design and Engineering
• /
• v.5 no.4
• /
• pp.359-372
• /
• 2000

Current CAD systems are good enough to be used as a tool to manipulate three-dimensional shapes. This is a very important capability to be owned by a design tool because a major portion of designers'activities is spent on the shape manipulation in the design detailing process. However, the whole design process involves a lot more than the, shape manipulation. Currently, these remaining tasks, mostly logical reasoning process for the function realization together with structure decomposition in the top-down manner, are processed in the designer's brain. To support the top-down functional design process of a mechanical product, a system integrating the functional, structural and geometrical aspects of a product design in a unified environment is presented. Using this system, a designer can perform function decomposition, structure decomposition, and geometry detailing, and function verification activities in parallel and the whole design process it modeled resultantly. Once the whole design process is modeled, any redesign task can be automatically performed with the verification of the desired functions.