• JSTS:Journal of Semiconductor Technology and Science
• /
• 제17권2호
• /
• pp.180-185
• /
• 2017

In this research, we proposed the simple and efficient method to calculate the shear stresses by using the mid-point measurements in ${\pm}45^{\circ}$ semiconductor resistor-sensor pair. Compared to the previous works, the measurements became much simpler by combining the approximation theory with the technique of mid-point measurement. In addition, we proposed another novel method for the stress calculation in which we could increase the sensitivity of the stress sensor by controlling the applied voltage between the sensor-pair. For the applied voltage of 8 V, the sensitivity showed a significant increase by 100%.

• 대한기계학회논문집A
• /
• 제22권3호
• /
• pp.569-578
• /
• 1998

The mode I and II stress intensity factors have been calculated theoretically for the cracked plate reinforced with a plate by symmetric spot welding under remote mixed mode loading. This is the extension of authors' previous work for the reinforced cracked plate under remote normal stress. Regardless of loading types, the reinforcement effect gets better as one joining spot is closer to the crack tip and the others are closer to the crack surface, and optimum number of the joining spots can be existed. For the present model, the remote loading parallel to crack surface produces the mode I stress intensity factor.

• 대한기계학회논문집
• /
• 제16권6호
• /
• pp.1216-1220
• /
• 1992

본 연구에서는 Lee등의 연구를 일반화하기 위하여 급수 형태의 등각사상함수 로 표현되는 일반형태의 커스프형 강체함유물이 존재하는 경우에 대하여 복소 포텐셜 함수와 TSIF에 대한 일반해를 구하기로 한다.

• Journal of Mechanical Science and Technology
• /
• 제18권11호
• /
• pp.1989-1995
• /
• 2004

Finite element analysis(FEA) is the most popular numerical method to simulate plasticity-induced fatigue crack closure and can predict fatigue crack closure behavior. Finite element analysis under plane stress state using 4-node isoparametric elements is performed to investigate the detailed closure behavior of fatigue cracks and the numerical results are compared with experimental results. The mesh of constant size elements on the crack surface can not correctly predict the opening level for fatigue crack as shown in the previous works. The crack opening behavior for the size mesh with a linear change shows almost flat stress level after a crack tip has passed by the monotonic plastic zone. The prediction of crack opening level presents a good agreement with published experimental data regardless of stress ratios, which are using the mesh of the elements that are in proportion to the reversed plastic zone size considering the opening stress intensity factors. Numerical interpolation results of finite element analysis can precisely predict the crack opening level. This method shows a good agreement with the experimental data regardless of the stress ratios and kinds of materials.

• International Journal of Automotive Technology
• /
• 제1권2호
• /
• pp.79-87
• /
• 2000

Analytical approach was followed in this work under both the steady state and transient operating conditions to find optimum boundary conditions, where the optically accessible quartz engine can run safely without breaking. Temperature and stress distribution was predicted by FEM analysis. In order to validate thermal boundary condition, model reliability and constraint, outside cylinder temperature was measured and previous study was also followed up numerically. To reduce thermal stress level, three types of outside cooling (natural, moderate forced and intensive forced convection) were considered. Effects of clamping force and combustion pressure were conducted to investigate mechanical stress level. Cylinder thickness, was changed to fine the optimum cylinder thickness. The versatile results achieved from this work can be basic indication, which is capable of causing a sudden quartz cylinder breaking during fired operation.

• 콘크리트학회논문집
• /
• 제12권1호
• /
• pp.89-99
• /
• 2000

The objective of this study is to investigate the bond strength properties of antiwashout underwater concrete. The arrangement of bars (vertical bar, horizontal upper bar, horizontal lower bar), condition of casting and curing (fresh water, sea water), type of fine aggregate (river sand, blended sand(river sand : sea sand = 1:1), and proportioning strength of concrete (210, 240, 270, 300, 330kgf/$\textrm{cm}^2$)are chosen as the experimental parameters. The test results(ultimate bond stress) are compared with bond and development provisions of the ACI Building Code(ACI 318-89) and proposed equations from previous research(which was proposed by Orangun et. al). The experimental results show that ultimate bond stress of antiwashout underwater concrete which arranged bar on the horizontal lower, used the blend sand, and was cast and cured in the fresh water are higher that other conditions. The ultimate bond stress were increased in proportion to {{{{( SQRT {fcu }) }}3 2. From this study, rational analytic formula for the ultimate bond stress are to be from compressive strength of concrete.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2010년도 춘계 학술대회 제22권1호
• /
• pp.141-142
• /
• 2010

본 연구는 고강도 콘크리트 유효응력 블록 계수 추정과 관련한 연구이다. 현행 KCI 코드에서 제시하는 등가직사각형 응력 분포는 고강도 콘크리트의 강도 분포를 정확히 예측하지 못하며, 실험 데이터에 기반한 제안식이 대부분이므로, 본 연구에서는 기존 연구자의 실험 데이터와 응력매개벼수의 이론적 개념을 바탕으로 하여 고강도 콘크리트의 유효응력블럭 계수 추정에 관한 연구를 수행하였다.

• 대한기계학회논문집
• /
• 제18권6호
• /
• pp.1382-1387
• /
• 1994

A model is constructed to evaluate the stress intensity factors for a center crack subjected to anti-symmetric loading in a layered material. A Fredholm integral equation is derived using the Fourier integral transform method. The integral equation is numerically analyzed to evaluate the effects of stress intensity factor on the shear modulus, Poisson's ratio and crack length to layer thickness. In case of the isotropic homogeneous material, the values of stress intensity factor derived in the present study agree with the previous solutions.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2000년도 추계학술대회 논문집
• /
• pp.369-372
• /
• 2000

ESO(Evolutionary Structural Optimization) method is known that elements involved low stress value are removed from the previous model or that elements are added around elements involved high stress level on it and then the optimized model is obtained with required weight. Rejection ratio/addition ratio and evolutionary ratio are predefined and elements having lower/higher stress than reference stress, which average Mises stress on edge elements times rejection ratio, are deleted/added. In this study, when the plate having a cutout is subjected various in-plane load, a cutout shape is optimized using ESO method. ANSYS is used to analyse a finite element model and optimization procedure is made by APDL (ANSYS Parametric Design Language). ESO method is useful in rather than a complex structure optimization as well as a cutout shape optimization.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2005년도 추계학술대회 논문집 Vol.18
• /
• pp.84-85
• /
• 2005

Dislocations are often found at Shallow Trench Isolation (STI) process after repeated thermal cycles. The residual stress after STI process often leads defect like dislocation by post STI thermo-mechanical stress. Thermo-mechanical stress induced by STI process is difficult to remove perfectly by plastic deformation at previous thermal cycles. Embedded flash memory process is very weak in terms of post STI thermo-mechanical stress, because it requires more oxidation steps than other devices. Therefore, dislocation-free flash process should be optimized.