• Journal of the Korean Society for Precision Engineering
• /
• v.15 no.3
• /
• pp.88-98
• /
• 1998

In many automatization applications, a rigid body is required to go forward and backward repeatedly through a set of given position/orientations precisely while a crank is rotated. Such a motion can be generated by 6 bar mechanism adding a dyad to a 4 bar mechanism. If this is the case for 3 position synthesis of the 4 bar mechanism, the feasible solution area for designing the 4 bar mechanism will be limited over the general solution area. This paper proposes a procedure to synthesize 4 bar mechanism to be used to generate the required motion. It is found that the only input crank of the 4 bar mechanism should be limited to satisfy the condition. And the feasible design area for the circle point/ center point of the input crank is identified so that design of the undesired mechanism could be avoided. The method is tested and the results are shown.

• International Journal of Precision Engineering and Manufacturing
• /
• v.6 no.4
• /
• pp.21-25
• /
• 2005

In the dynamic analysis of a mechanism, if one or more of the components are flexible, then the simulation will not be accurate because of the violation of the rigid body assumption. Mode shapes are used to represent the dynamic behavior of an elastic structure. A modal synthesis method which uses a combination of normal modes, constraint modes, and attachment modes, was used to represent effectively the elastic deformation of a flexible multibody. Since the combination of these modes should be different for each type of connecting part, the modal synthesis method was studied for the various types of interconnecting joints. In addition, the analysis procedure for the flexible body was explained. A satellite system with flexible solar panels was chosen as an example to show the effectiveness of the proposed method.

• Journal of the Korean Society for Precision Engineering
• /
• v.15 no.11
• /
• pp.67-75
• /
• 1998

Geometric and thermal errors are key contributors to the errors of a computer numerically controlled turning center. A planar error synthesis model is obtained by synthesizing 11 geometric and thermal error components of a turning center with homogeneous coordinate transformation method. This paper shows the sensitivity analysis on the temperature change, the confidence evaluation on the uncertainty Of measurement systems, and the error contribution analysis from the planar error synthesis model. Planar error in the z direction was very sensitive to the temperature change. and planar errors in the x and z directions were not affected by the uncertainty of measurement systems. The error contribution analysis ,which is applicable to designing a new turning center, was helpful to find the large error components which affect planar errors of the turning center.

• Journal of the Korean Society for Precision Engineering
• /
• v.12 no.6
• /
• pp.80-86
• /
• 1995

A method of eliminating the branch problem in driving crank center point plane for 3 position synthesis of 4 bar mechanism is introduced. By studying various transformation characteristics from the circle point plane into the center poi t plane, the curves in the center point plane transformed from the filemon line in circle point plane are analytically obtained, which will seperate the whole center point plane into many sub-areas for the selec- tion of the center point of the driving crank. And a simple method to identify which of the sub-areas will cause the branch problem is also presented. The method will allow the selection of the center point of driving crank without the branch problem.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.18 no.6
• /
• pp.576-584
• /
• 2009

Up to now, it has been said that no satisfactory computer solution has been found for synthesizing four-bar linkage based on the prescribed coupler link curve. In our study, an algorithm has been developed to improve the design synthesis of four bar linkage based on the 5 precision points method. The suggested algorithm generates the desired coupler curve by using NURBS, and then the generated curve approximates as closely as possible to the desired curve representing coupler link trajectory. Also, when comparing each generated curve by constructing the control polygon, rapid comparison is easily achieved by applying convex hull of the control polygon. Finally, an optimization process using ADS is incorporated into the algorithm based on the 5 precision point method to reduce the total optimization process time. As for examples, two four bar linkages were tested and the result well demonstrated the effectiveness of the algorithm.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.24 no.11
• /
• pp.2665-2671
• /
• 2000

Dimensional Synthesis, which is apart of kinematic synthesis, is to determine the dimensions of a mechanism of preconceived typer for a specified task and prescribed performance. In this paper, in an effort to provide designers with flexibility, a dimensional approximate synthesis method is presented for utilizing prescribed tolerance both the displacement and joint positions of a mechanism to be synthesized. For this, a constrained optimization problem is formulated with displacement parameters and joint positions as variables. The proposed method is applied to the synthesis of a 5-SS multi link suspension mechanism. The method discussed here, however, can be easily applied to any mechanism of which the kinematic constraint equations can be derived.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2008.11a
• /
• pp.33-34
• /
• 2008

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2010.05a
• /
• pp.1141-1142
• /
• 2010

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2006.10a
• /
• pp.49-50
• /
• 2006

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2008.06a
• /
• pp.537-538
• /
• 2008