• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.22 no.9
• /
• pp.1941-1948
• /
• 1997

In this paper, the power efficient linear upconversion mixer which is a functional circuit in transmit path of intermediate frequency(IF) part of Code Division Multiple (CDMA) cellular phone was explained. In generally, the low CMOS devices limits the implementation of upconversion mixer especially for lower loads. Using replica transconductor, the linear range is extended up to the limit. Thiscircuit was imprlemented using $0.8{\mu}\textrm{m}$ N-well CMOS technology with 2-poly/2-metal. The active area of chip is $0.53mm{\times}0.92mm$. The power consumption is 30mW with 3.3V suply voltage. The 1dB conpression characteristics is -27.3dB with $25{\Omega}$. load and being applied by 2-tone input signal. The mixer operates properly above 200MHz.

• International Journal of Naval Architecture and Ocean Engineering
• /
• v.8 no.4
• /
• pp.330-343
• /
• 2016

This paper presents results of an experimental investigation of vortex-induced vibration (VIV) of a flexibly mounted and rigid cylinder with two-degrees-of-freedom with respect to varying ratio of in-line natural frequency to cross-flow natural frequency, $f^*$, at a fixed low mass ratio. Combined in-line and cross-flow motion was observed in a sub-critical Reynolds number range. Three-dimensional displacement meter and tension meter were used to measure dynamic responses of the model. To validate the results and the experiment system, x and y response amplitudes and ratio of oscillation frequency to cross-flow natural frequency were compared with other experimental results. It has been found that the higher harmonics, such as third and more vibration components, can occur on a certain part of steel catenary riser under a condition of dual resonance mode. In the present work, however, due to the limitation of a size of circulating water channel, the whole test of a whole configuration of the riser at an adequate scale for VIV phenomenon was not able to be conducted. Instead, we have modeled a rigid cylinder and assumed that the cylinder is a part of steel catenary riser where the higher harmonic motions could occur. Through the experiment, we have found that even though the cylinder was assumed to be rigid, the occurrence of the higher harmonic motions was observed in a small reduced velocity ($V_r$) range, where the influence of the in-line response is relatively large. The transition of the vortex shedding mode from one to another was examined by using time history of x and y directional displacement over all experimental cases. We also observed the influence of in-line restoring force power spectral density with $f^*$.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.38C no.9
• /
• pp.813-821
• /
• 2013

In this paper, a vital signal sensor based on impedance variation of resonator is presented. Proposed vital signal sensor can detect the vital signal, such as respiration and heart-beat signal. System is composed of resonator, oscillator, surface acoustic wave (SAW) filter, and power detector. The cyclical movement of a dielectric such as a human body, causes the impedance variation of resonator within the near-field range. So oscillator's oscillation frequency variation is effected on resonator's resonant frequency. SAW filter's skirt characteristic of frequency response can be transformed a small amount of frequency deviation to a large variation. Aim to enhance the existing sensor detection range, proposed sensor operates in 870 MHz ISM band, and detect respiration and heart-beat signal at distance of 120 mm.

• Journal of Navigation and Port Research
• /
• v.26 no.2
• /
• pp.235-243
• /
• 2002

Theoretical analysis have been performed to design the high power semiconductor laser for an optical sensor at 1.55${\mu}{\textrm}{m}$ wavelength range which is the lowest loss wavelength in optical fiber. The materials of active region and SCH were $Ln_{1-x}Ga_xAs_yP_{1-y}$. In order to use the light source of optical sensors, it has to satisfy wide spectral width and short coherence length. Therefore, in order to suppress lasing oscillation, we proposed laterally tilted PBH type with a window region. Also, tapered stripe structure was applied for high coupling efficiency into a single mode fiber. From these analyses, the devices of laterally tilted angled and bending structure were fabricated and their characteristics were measured. In the results of the measurement, the fabricated devices have sufficient output power and wide FWHM to apply to the light source of optical fiber sensors.

• Journal of Power Electronics
• /
• v.16 no.1
• /
• pp.227-237
• /
• 2016

A novel digital current control strategy for digitally controlled DC-DC switching converters, referred to as Adjacent Cycle Sampling (ACS), is proposed in this paper. For the ACS current control strategy, the available time interval from sampling the current to updating the duty ratio, is approximately one switching cycle. In addition, it is independent of the duty ratio. As a result, the contradiction between the processing speed of the hardware and the transient response speed can be effectively relaxed by using the ACS current control strategy. For digitally controlled buck DC-DC switching converters with trailing-edge modulation, digital current control algorithms with the ACS control strategy are derived for three different control objectives. These objectives are the valley, average, and peak inductor currents. In addition, the sub-harmonic oscillations of the above current control algorithms are analyzed and eliminated by using the digital slope compensation (DSC) method. Experimental results based on a FPGA are given, which verify the theoretical analysis results very well. It can be concluded that the ACS control has a faster transient response speed than the time delay control, and that its requirements for hardware processing speed can be reduced when compared with the deadbeat control. Therefore, it promises to be one of the key technologies for high-frequency DC-DC switching converters.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.12 no.1
• /
• pp.33-38
• /
• 2008

The probability of an oscillation occurrence in M/W frequency conversion repeaters is low on account of the different operating frequency of the input and output signals. The probability of interference caused by the M/W frequency conversion repeaters to other systems is also low because the systems are used in the line-of-sight. Therefore M/W frequency conversion repeaters are generally used for retransmitting the signal received from base station to the islands. This paper describes the design and implementation of analog predistorter for M/W frequency conversion repeaters in mobile communications. The M/W repeaters convert IF frequency of 1010+/-10MHz to RF frequency of 11GHz. A predistorter can be designed for the M/W repeater operating in either IF or M/W frequency. In this paper IF predistorter operated in 1010MHz is designed and implemented because a M/W predistorter operated in 11GHz is difficult to implement. The IF predistorter can linearize RF modules in the repeater followed by IF stages. The performance test results show that the implemented analog predistorter improves ACPR of 10dB at the output power of 25dBm with the signal frequency of 10.805GHz.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.44 no.12
• /
• pp.1-6
• /
• 2007

In this study, we have performed the channel modification of the conventional MHEMT (metamorphic high electron mobility transistor) to improve the breakdown characteristics. The Modified channel consists of the InxGal-xAs channel and the InP sub channel instead of the InxGa1-xAs channel. Since InP has the lower impact ionization coefficient in comparison with In0.53Ga0.47As, we have adopted the InP-composite channel in the modified MHEMT. We have investigated the breakdown mechanism and the RF characteristics for the conventional and the InP- composite channel MHEMTs. From the measurement results, we have obtained the enhanced on and off-state breakdown voltages of 2.4 and 5.7 V, respectively. Also, the increased RF characteristics have brought about the decreased output conductance for the InP-composite channel MHEMT. The cut-off frequency (fT) and the maximum oscillation frequency (fmax) for the InP-composite Channel MHEMT were 160 GHz and 230 GHz, respectively. It has been shown that the InP-composite channel MHEMT has the potential applications for the millimeter wave power device.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.20 no.6
• /
• pp.570-579
• /
• 2009

In this paper, we presented a Vt-DRO with a wide electrical frequency tuning range, using open-loop gain method. The Vt-DRO was composed of 3-stages, resonator, amplifier and phase shifter. In order to satisfy an oscillation condition, we determined magnitude and phase of each stage. The measured S-parameter of cascaded 3-stages shows open-loop oscillation condition. Also, using measured open loop group delay, we derived the relation for electrical frequency tuning range. The Vt-DRO was implemented by connecting the input and the output of the designed open-loop and resulted in closed-loop. As a results, tuning-range of Vt-DRO is 82 MHz, which is close to the predicted results for tuning voltage 0${\sim}$10 V and shows linear frequency tuning at the center frequency of 5.3 GHz. The phase noise is -104 ${\pm}$1 dBc/Hz at 100 kHz offset frequency and power is 5.86${\pm}$1 dBm respectively.

• Korean Journal of Optics and Photonics
• /
• v.19 no.1
• /
• pp.68-72
• /
• 2008

Fiber-optic strain sensors based on Bragg reflection gratings produce the change of reflection spectrum when an external stress is applied on the sensor. To measure the Bragg reflection wavelength in high speed, an arrayed waveguide grating device is incorporated in this work. By monitoring the output power from each channel of the AWG, the peak wavelength corresponding to the applied strain could be obtained. To enhance the accuracy of the AWG wavelength interrogation system, a chirped fiber Bragg grating with a 3-dB bandwith of 5.4 nm is utilized. The high-speed response of the proposed system is demonstrated by measuring a fast varying strain produced by the damped oscillation of a cantilever. An oscillation frequency of 17.8 Hz and a damping time constant of 0.96 second are obtained in this measurement.

• Journal of Software Assessment and Valuation
• /
• v.16 no.1
• /
• pp.55-63
• /
• 2020

Lasers for optical broadband communication systems should have excellent frequency selectivity and modal stability. DFB lasers have low lasing frequency shift during high speed current modulation. In this paper, when a refractive index grating and a gain grating are simultaneously present in a DFB laser having a wavelength of 1.55 ㎛, the dielectric film is coated so that reflection does not occur on the right mirror surface, so that ρ_r=0. For the first mode, which requires a minimum gain at the threshold, the beam distribution of the oscillation mode in the longitudinal direction and the radiated power ratio P_l/P_r were analyzed and compared for the cases of the phase of ρ_l=π and π/2. If the phase of ρ_l=π, in order to obtain a low threshold current and high frequency stability, κL should be greater than 8. In the case of the phase of ρ_l=π/2, for low threshold current, κL is necessary to be 1.0, where the oscillation frequency coincides with the lattice frequency. DFB lasers with an anti-reflection coated mirror have excellent mode selectivity than 1.55um DFB lasers with two mirror facets