• Proceedings of the Korea Concrete Institute Conference
• /
• 1996.10a
• /
• pp.394-400
• /
• 1996

Recently, the construction of infrastructures has been booming and acceleratin to keep up with rapid economic growth. Consturction activities and operation of transportation facilities caues unfavorable effects such as civil petitions associated with vibration-induced damages or nuisances. Vibration-controlled mixtures are latex, rubber powder and plastic resin, which have been deternimed to reduce vibration by and large reduce vibration. KS F2437 and travel time method have been used to figure out 1st natural frequency and dynamic elastic moduli. Dynamic damping ratios have been computed by adopting the polynomial curvefitting method and the geometric analysis method on the frequency spectrum curve, of which results have been compared and analyzed hereon.

• 한국신재생에너지학회:학술대회논문집
• /
• 2008.05a
• /
• pp.73-76
• /
• 2008

Bipolar Plates for PEMFC have been a key component of fuel cells with MEA, thus in this research they have been fabricated by a compression molding technique after mixing graphite powder with phenol resin. The results have shown the prominent properties compared with those by foreign advanced company with respect to the electrical conductivity and flexural strength. In addition, it has been carried out that the Voltage-Current characteristics comparison according to the unit cell experiments of bipolar plates. As a result, we have obtained good performances and we are going to research the molding feasibility of bipolar plate's flow channel.

• Applied Chemistry for Engineering
• /
• v.28 no.3
• /
• pp.360-368
• /
• 2017

In order to investigate the durability of high performance polymer concrete composites, polymer concrete specimens were prepared using the ortho-type unsaturated polyester resin (UPR) and iso-type UPR as a polymer binder and the calcium carbonate and silica fine powder as a filler. The durability of polymer concrete specimens was measured by hot water resistance, chemical resistance, pore analysis and SEM observation. The compressive strength of the specimen using the iso-type UPR was higher than that of using the ortho-type UPR, and the compressive strength of the specimen using the silica fine powder was higher than that of using the calcium carbonate filler. From hot water resistance results, it was found that the specimen using the iso-type UPR was superior to that of using the ortho-type UPR and the specimen using the calcium carbonate filler was superior to that of using the silica fine powder. The compressive strength reduction rate was measured after the chemical resistance test and the sodium hydroxide solution showed the highest reduction rate, followed by sulfuric acid, hydrochloric acid and calcium chloride solutions. When using the alkaline solution of sodium hydroxide, the weight reduction rate of the specimen using calcium carbonate was lower than that of using silica fine powder, while for the acidic solutions of sulfuric acid and hydrochloric acid, the weight reduction rate of the specimen using the silica fine powder was lower than that of using calcium carbonate.

• Applied Chemistry for Engineering
• /
• v.21 no.2
• /
• pp.217-223
• /
• 2010

In general, fiber-reinforced plastics (FRP) wastes are simply buried or burned. Landfill brings about a permanent contamination of soil due to the inability of FRP to decompose and incineration causes an issue of generating toxic gases and dusts. There have been several ways to treat the FRP wastes such as landfill, incineration, chemical recycling, material recycling and the utilization of energy from combustion. Most methods excluding material recycling are known to have critical limitations in economic, technical and environmental manners. However it is known that material recycling is most desirable among the methods handling FRP wastes. In this study, to investigate the purpose of feasibility of material recycling, various bulk molding compound (BMC) specimens were prepared with the various contents of unsaturated polyester resin binder (25, 30, 35 wt%) and the various replacement ratios of FRP wastes powder (0, 25, 50, 75, 100 wt%) substituted for filler. To evaluate the physical properties BMC specimens, various tests such as tensile strength, flexural strength, impact strength, hot water resistance and SEM imaging were conducted. As a results, mechanical strengths decreased with an increase of replacement ratio of FRP waste powder and physical properties of BMC specimens were deteriorated in the hot water resistance. The fluidity of BMC with more than 50 wt% of the replacement ratio of FRP wastes powder decreased remarkably, causing a problem in the BMC composite.

• Composites Research
• /
• v.31 no.5
• /
• pp.209-214
• /
• 2018

This paper explain about the development of environmental friendly, low cost and stable supply material i.e., rice husk and shell were used as micro incorporating bio waste filler. Those were processed by ball mill and analyzed through micro observation by FE-SEM, EDS and particle size distribution. The obtained filler was mixed with epoxy resin for the manufacturing of CFRP composite and study tensile properties. In EDS analysis main contents of rice husk and rice husk ash are C, O and Si. When rice husk was burned C and Si ration were increased. Shell powder has C, O and Ca. It caused $CaCO_3$ from shell. Surface weighted mean of rice husk powder is $6.19{\mu}m$ and volume weighted mean is $14.77{\mu}m$. And it has rod type particles which caused hair and husk structure parts. Surface weighted mean of rice husk ash powder is $1.55{\mu}m$ and volume weighted means is $8.20{\mu}m$. Surface weighted mean of shell powder is $2.53{\mu}m$ and volume weighted mean is $5.79{\mu}m$. The tensile decreased with increasing the content of micro filler in CFRP composites. In case of rice husk, the significant decrement of tensile strength was observed. and in case of shell powder, there is no effect of changes take place in tensile strength.

• Magazine of the Korea Concrete Institute
• /
• v.9 no.6
• /
• pp.185-193
• /
• 1997

본 연구는 각종 제진재료를 이용하여 진동을 억제할 수 있는 콘크리트를 개발하여 각종 건설공사에서 흔히 발생할 수 있는 진동공해문제를 억제하고자 하며 아울러 폐기물의 재활용차원에서 폐자재를 이용하여 유용한 제진콘크리트를 개발하고자 하는데 그 목적이 있다. 우선, 제진재료를 이용한 압축강도 (200kg/$\textrm{cm}^2$)이상의 콘크리트 배합비를 찾기 위하여 24배치의 예비실험을 수행하였으며, 선정된 적정배합비에 따른 제진재료를 이용한9개의 진동시험체보를 제작하여 보의 구조적 및 재료적 동적특성 즉 1차 공명진동수와 동적 휨강성 및 감쇠비를 측정하여 제진효과를 조사하였다. 그리고 압축강도에 의한 각 시험체의 균열모멘트를 추정하여 재하하중과 균열모멘트비(M/Mcr)에 따른 하중단계별 동적특성값을 살펴보았다. 제진재료로서는 라텍스(Latex), 고무분말(Rubber Powder)그리고 플라스틱 레진( Plastic Resin)등을 사용하였고, 재료적, 구조적 진동감쇠효과를 파악하고자 KS F2437규정과 진동파의 속도법을 사용하였으며, 감쇠비 측정은 Frequency Spectrum 곡선에 대한 Polynomial Curvefitting 방법과 기하학적 해석방법을 이용하여 각각의 결과를 비교.분석하였다.

• Journal of the Korean Society of Safety
• /
• v.26 no.2
• /
• pp.13-19
• /
• 2011

The magnetic polishing is the useful method to finish using magnetic power of magnet. That method is one of precision polishing techniques and has an aim of the clean technology using for the pure of gas and inside of the clean pipe. The magnetic abrasive polishing method is not so common for machine that it is not spreaded widely. There are rarely researcher in this field because of non-effectiveness of magnetic abrasive. Therefore, in this paper deals with development of the magnetic abrasive using Sr-Ferrite. In this development, abrasive grain GC used to resin bond fabricated low temperature. And Sr-Ferrite of magnetic abrasive powder fabricated that Sr-Ferrite was crused into 200 mesh. The XRD analysis result show that only GC abrasive and Sr-Ferrite crystal peaks detected which explains resin bond was not any more chemical reaction. From SEM analysis it is found that GC abrasive and Sr-Ferrite were strong bonding with each other by bond. The magnetic polishing is performed by polishing the surface of pipe by attracting magnetic abrasives with magnetic fields. This can be widely applied for finishing machinery fabrications such as various pipes and for other safety processes. In this paper, we could have investigated in to the changes of the movement of magnetic abrasive grain. In reference to this result, we could have made the experiment which is set under the condition of the magnetic flux density, polishing velocity according to the form of magnetic brush.

• Journal of the Korean Wood Science and Technology
• /
• v.51 no.5
• /
• pp.334-344
• /
• 2023

Dregs from the sugar palm (Arenga pinnata) starch industry are considered a waste product of the agricultural industry and have not yet been optimally utilized. Therefore, this study aimed to manufacture particleboards from dregs using different amounts of adhesive and particle size ratios. Sugar palm dregs, which had been separated into fibers and powder/fine particles, were used as raw material for making particleboards. The fiber had an average length of 6.84 ± 3.23 cm, while the fine particles were of a size that passed through size 10 mesh and remained in size 60 mesh. Three ratios of fiber to fine particles (100:0, 75:25, and 50:50 wt%) with three different amounts of sucrose-citric acid adhesive (10, 15, and 20 wt%) were used in this study. Increasing the amount of fine particles and the resin content can improve the physical properties and the internal bond strength of boards made from sugar palm dregs. The fine particles possibly filled the gap between the fibers in the particleboard, while the fibers exhibited a high bending strength. As a result, a high-performance particleboard can be attained by combining the composition ratio of fiber/fine particles and resin content. In this study, particleboards made from fiber/fine particles (75:25 wt%) and adhesive content of 15 wt% and 20 wt% had the mechanical properties that met the requirements of Japanese Industrial Standard (JIS) A 5908 type 18. Sugar palm dregs have the potential to be used as raw materials to create value-added particleboards.

• Korean Journal of Materials Research
• /
• v.27 no.12
• /
• pp.664-671
• /
• 2017

A composite material was prepared for the bipolar plates of phosphoric acid fuel cells(PAFC) by hot pressing a flake type natural graphite powder as a filler material and a fluorine resin as a binder. Average particle sizes of the powders were 610.3, 401.6, 99.5, and $37.7{\mu}m$. The density of the composite increased from 2.25 to $2.72g/cm^3$ as the graphite size increased from 37.7 to $610.3{\mu}m$. The anisotropy ratio of the composite increased from 1.8 to 490.9 as the graphite size increased. The flexural strength of the composite decreased from 15.60 to 8.94MPa as the graphite size increased. The porosity and the resistivity of the composite showed the same tendencies, and decreased as the graphite size increased. The lowest resistivity and porosity of the composite were $1.99{\times}10^{-3}{\Omega}cm$ and 2.02 %, respectively, when the graphite size was $401.6{\mu}m$. The flexural strength of the composite was 10.3MPa when the graphite size was $401.6{\mu}m$. The lowest resistance to electron mobility was well correlated with the composite with lowest porosity. It was possible the flaky large graphite particles survive after the hot pressing process.

• Journal of Microbiology and Biotechnology
• /
• v.26 no.12
• /
• pp.2051-2059
• /
• 2016

To date, there has been no employment of a magnetoelastic (ME) biosensor method to detect Salmonella enterica serovar Typhimurium in soil. The ME biosensor method needs to be investigated and modified for its successful performance. The filtration method, cation-exchange resin method, and combinations of both methods were employed for the extraction of S. Typhimurium from soil. The number of S. Typhimurium and the resonant frequency shift of the ME sensor were then compared using a brilliant green sulfa agar plate and an HP 8751A network analyzer. A blocking study was performed using bovine serum albumin (BSA), polyethylene glycol (PEG), and casein powder suspension. Finally, the modified ME biosensor method was performed to detect S. Typhimurium in soil. The number of S. Typhimurium was significantly decreased from 7.10 log CFU/soil to 4.45-4.72 log CFU/soil after introduction of the cation-exchange resin method. The greatest resonant frequency shift of the measurement sensor was found when employing centrifugation and filtration procedures. The resonant frequency shift of the PEG-blocked measurement sensor was $3,219{\pm}755Hz$, which was significantly greater than those of the BSA- and casein-blocked ME sensor. The optimum concentration of PEG was determined to be 1.0 mg/ml after considering the resonant shift and economic issue. Finally, the modified ME biosensor method was able to detect S. Typhimurium in soil in a dose-response manner. Although these modifications of the ME biosensor method sacrificed some advantages, such as cost, time effectiveness, and operator friendliness, this study demonstrated a novel approach of the ME biosensor method to detect S. Typhimurium in soil.