• Journal of the korean academy of Pediatric Dentistry
• /
• v.24 no.2
• /
• pp.428-435
• /
• 1997

For the purpose of investigating the continuous fluoride releasing from acrylic resin using removable appliances by incorporating fluoride into polymethylmethacrylate during the construction of the appliances, two kinds of fluoride were blended with acrylic powder and devided into five groups as follows. Group 1 : no fluoride (control) Group 2 : NaF 5 wt% Group 3 : NaF 10 wt% Group 4 : $CaF_2$ 5 wt% Group 5 : $CaF_2$ 10 wt% Resin specimens were tested in vitro for fluoride release with fluoride electrode and flexural strength with Instron. The results were as follows ; 1. After 24 hrs, released fluoride concentration(ppm) was the most in group 3($126.5{\pm}14.15$) then, next, group 2($49.5{\pm}4.92$), group 5($2.67{\pm}1.08$), group 4($0.81{\pm}0.30$), group 1($0.03{\pm}0.01$) in order, but after 28 days, group 3($3.37{\pm}0.31$), group 5($1.25{\pm}0.25$), group 4($0.74{\pm}0.19$), group 2($0.68{\pm}0.07$), group 1($0.03{\pm}0.01$). 2. Fluoride releasing of NaF groups were faster and more amount than $CaF_2$ groups initially but decreased significantly, later. 3. Flexural strength ($kg/cm^2$) was the biggest in group 1($602.90{\pm}69.32$), and then group 4($568.98{\pm}20.16$), group 5($556.19{\pm}5.26$), group 2($536.12{\pm}30.35$), group 3($508.44{\pm}26.16$) in order, the differences between control group and NaF groups were statistically significant (p<0.05).

• Journal of Conservation Science
• /
• v.25 no.4
• /
• pp.439-450
• /
• 2009

The purpose of this study is to find out characteristics of the fillers made by epoxy resin (L-30) and filling epoxy resin (L-50) with talc, quartz sand and wollastonite with different mixture ratio of 5%, 50%, 80%, 120%, and 150%. The viscometer and colorimeter were used to measure the viscosity and chromaticity of the fillers. Additionally, IC and SEM were used to reveal characteristics of the filler, and checked ultrasonic wave velocity, compressive strength and contact angle to estimate the stability between the filler and stones which are essential for conservation treatments. The filler mixed with the talc had the lowest value in the ultrasonic wave velocity analysis, and its compressive strength decreased as the mixing rate of talc increased. On the other hand, wollastonite had higher values than others in the ultrasonic wave velocity and the compressive strength regardless of epoxy resin type, also, these values increased as mixing rate increased. The properties of the filler, which include the granularity and shape, have influence on characteristics of the stone conservation adhesives. Thus, the filler type, characteristic, and mixture ratio must be considered for effective conservation treatment.

• Resources Recycling
• /
• v.17 no.4
• /
• pp.47-56
• /
• 2008

The aim of this study is to produce cokes which can be used for the production of ferroalloy, for this purpose, domestic anthracite mixed with plastic was sintered at various condition. The combustion and physical properties of anthracite and plastic, coal separation, and the influence of factors on the strength of coke were investigated. The results of this study are as follows: 1. The three kinds of anthracite from the Samcheok region contained 25 to 30% ash of $100{\mu}m$ over size, and have the caloric value of 5,205 cal/g(TaeAn), 4,893 cal/g(JangSung), 4,873cal/g(KyongDong). 2. The recommendable conditions for heavy-fluid separation of the Samcheok coal are to set the specific gravity of heavy fluid to 2.4 and control the size of coal to $35{\sim}140mesh$. 3. It is concluded that phenolic resin powder, liquefied phenolic resin, SAN, and melamine resin can be used as a binder for the anthracite cokes, from the thermal analysis of various plastics. Especially, the liquefied phenolic resin was considered as the most suitable binder as it would simplify the process.

• Journal of the Korea Safety Management & Science
• /
• v.11 no.4
• /
• pp.311-317
• /
• 2009

In this paper deals with behavior of the magnetic abrasive using Ba-Ferrite on polishing characteristics in a new internal finishing of STS304 pipe applying magnetic abrasive polishing. The magnetic abrasive using Ba-Ferrite grain WA used to resin bond fabricated low temperature. And Ba-Ferrite of magnetic abrasive powder fabricated that Ba-Ferrite was crused into 200 mesh. The previous research have made an experiment in the static state the movement of magnetic abrasive grain is nevertheless in the dynamic state. In this paper, We could have investigated into the changes of the movement of magnetic abrasive grain. In reference to this result, we could have made the experiment which is set under the condition of the magnetic flux density, polishing velocity according to the form of magnetic brush.

• Transactions on Electrical and Electronic Materials
• /
• v.6 no.3
• /
• pp.128-132
• /
• 2005

In this paper, we have investigated the characteristics of the magnetic abrasive using sludge on polishing of internal finishing of seamless stainless steel (STS304) tube applying magnetic abrasive polishing. Either white alumina (WA) or green carborundum (GC) grain was used to resin sludge at a low temperature, and the sludge of magnetic abrasive powder was synthesized and crushed into 200 meshes. Surface roughness was measured before and after polishing, and more than $40\%$ of improvement of surface roughness was achieved when WA grain was used under a specific condition. Even though some degree of surface roughness due to deeper scratches still exist, but the result showed a prospective magnetic abrasive polishing using sludge with WA or GC grains.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.12 no.6
• /
• pp.151-157
• /
• 2004

In this paper deals with behavior of the magnetic abrasive using sludge on polishing characteristics in a new internal finishing of seamless stainless steel tube applying magnetic abrasive polishing. The magnetic abrasive using sludge-abrasive grain WA and GC used to resin bond fabricated low temperature. And sludge of magnetic abrasive powder fabricated that sludge was crused into 200 mesh. The previous research have made an experiment in the static state the movement of magnetic abrasive grain is nevertheless in the dynamic state. In this paper, We could have investigated into the changes of the movement of magnetic abrasive grain. In reference to this result, we could have made the experiment which is set under the condition of the magnetic flux density, polishing velocity according to the form of magnetic brush.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2004.11a
• /
• pp.77-80
• /
• 2004

In this paper, we have investigated the characteristics of the magnetic abrasive using sludge on polishing of internal finishing of seamless stainless steel (STS304) tube applying magnetic abrasive polishing. Either white alumina (WA) or green carborundum (GC) grain was used to resin sludge at a low temperature, and the sludge of magnetic abrasive powder was synthesized and crushed into 200 meshes. Surface roughness was measured before and after polishing, and more than 40% of improvement of surface roughness was achieved when WA grain was used under a specific condition. Even though some degree of surface roughness due to deeper scratches still exist, but the result showed a prospective magnetic abrasive polishing using sludge with WA or GC grains.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2003.06a
• /
• pp.565-568
• /
• 2003

In this paper we deal with behavior of the magnetic abrasive using Ba-Ferrite on polishing characteristics in a new internal finishing of STS304 pipe applying magnetic abrasive polishing. The magnetic abrasive using Ba-Ferrite grain WA was used to resin bond fabricated at low temperature. And Ba-Ferrite of magnetic abrasive powder was crused into 200 mesh. The previous research made an experiment in the static and the dynamic state on the movement of magnetic abrasive grain. In this paper. We investigated into the changes of the movement of magnetic abrasive grain. In reference to this result. we have made the experiment which is set under the condition of the magnetic flux density. polishing velocity according to the form of magnetic brush.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.5 no.4
• /
• pp.18-25
• /
• 1996

In this study, we have developed the stereolithography system that supports the development of a products. This paper presents the development of the stereolithography system. The system is composed of hardware, software and control part. The software converts a STL file to NC data and displays the monitoring figure in control part. The hardware part deals with structure of machine. The most important theme in this paper is LG-SLCAM software. This software can generate NC data and scanning condition data from a STL file semiautimatically. On the basis of three diensional shapes, it makes data for support structure from STL file. The effectiveness of using out stereolithography system is confirmed by processes of good development.

• Journal of the Speleological Society of Korea
• /
• no.78
• /
• pp.23-27
• /
• 2007

In this paper, we have investigated the characteristics of the magnetic abrasive using sludge on polishing of internal finishing of seamless stainless steel tube applying magnetic abrasive polishing. Either white alumina grain was used to resin sludge at a low temperature, and the sludge of magnetic abrasive powder was synthesized and crushed into 200 meshes. Surface roughness was measured before and after polishing, and more than 40% of improvement of surface roughness was achieved when grain was used under a specific condition. Even though some degree of surface roughness due to deeper scratches still exist, but the result showed a prospective magnetic abrasive polishing using sludge with white alumina grains.