• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2010년도 추계학술대회 초록집
• /
• pp.46.1-46.1
• /
• 2010

Surface passivation of crystalline silicon(c-Si) surface with a-Si:H thin films has been investigated by using quasi-steady-state photo conductance(QSSPC) measurements. Analyzing the influence of a-Si:H film thickness, process gas ratio, deposition temperature and post annealing temperature on the passivation properties of c-Si, we optimized the passivation conditions at the substrate temperature of $200-250^{\circ}C$. Best surface passivation has been obtained by post-deposition annealing of a-Si:H film layer. Post annealing around the deposition temperature was sufficient to improve the surface passivation for silicon substrates. We obtained effective carrier lifetimes above 5.5 ms on average.

• Bulletin of the Korean Chemical Society
• /
• 제25권12호
• /
• pp.1859-1862
• /
• 2004

Europium doped yttrium vanadate ($YVO_4$:Eu) phosphor thin films were grown using a pulsed laser deposition (PLD) technique on silicon substrate. The structural characterization carried out on a series of ($YVO_4$:Eu films at post annealing temperature in the range of 550 $^{\circ}C$-1150 $^{\circ}C$ indicating that films were preferentially (200) oriented at post annealing temperature above 950 $^{\circ}C.$ Photoluminescence of thin film increased with the increase of post annealing temperature and ambient oxygen pressure though the thin film has the powder-like surface morphology at oxygen pressure above 200 mTorr. Photoluminescence decay from $^5D_1$ level of $Eu^{3+}$ show the great concentration dependency, which can be used as a good parameter to control the composition of ($YVO_4$:Eu thin film.

• 한국세라믹학회지
• /
• 제33권3호
• /
• pp.299-306
• /
• 1996

We invesgated the fesibility of thin films deposition by pyrolysis of metalorganic precursors using chemical beam deposition (CBD) process. We attempted to understand the effects of deposition variables such as substrate temperature operating pressure effusion cell temperature and H2 partial pressure on the properties of MgF2 grown by CBD. Mg(tfac)2 was used as a precursor. MgF2 thin films were always grown in an amorphous state and crystallized bypost-annealing. he higher the substrate temperature and the lower the operating pressure the less the impurities I the deposited MgF2 thin films. H2 gas has to be supplied for the pyrolitic reaction of Mg(tfac)2 decomposition. MgF2 films annealed in H2 have lower C impurity than those annealed in O2. But their crysatllinity was independent of annealing atmosphere. The optimum conditions for the prepara-tion of MgF2 films by CBD process were as following : The substrate temperature 55$0^{\circ}C$ the operating pressure 10-4 torr; effusion cell temperature 21$0^{\circ}C$ the percentage of H2 100% Post-annealing in H2 gas was required to remove residual carbon and to form MgF2 crystalline phase.

• 열처리공학회지
• /
• 제25권5호
• /
• pp.239-243
• /
• 2012

$SnO_2$ thin films were prepared on the Si substrate by radio frequency (RF) magnetron sputtering and then post deposition vacuum annealed to investigate the effect of annealing temperature on the structural properties and hydrogen gas sensitivity of the films. The films that annealed at $300^{\circ}C$ show the higher sensitivity than the other films annealed at $150^{\circ}C$. From atomic force microscope observation, it is supposed that post deposition annealing promotes the rough surface and also, increase gas sensitivity of $SnO_2$ films for hydrogen gas. These results suggest that the vacuum annealed $SnO_2$ thin films at optimized temperatures are promising for practical high-performance hydrogen gas sensors.

• 한국전기전자재료학회논문지
• /
• 제13권1호
• /
• pp.28-32
• /
• 2000

Structural and electrical properties of (Ba, Sr)TiO\ulcorner (BST) thin films prepared by pulsed laser depositon were investigated to verify the influences of post-annealing in oxygen ambient. Increase of post-anneal-ing time in oxygen ambient resulted in not only grain growth but also improvement of crystallinity of BST films. Although the post-annealing in oxygen ambient resulted in the increase of surface roughness, it assisted the dielectric constant increase by eliminating oxygen vacancies. The electrical property enhancement including high dielectric constant and low leakage current density was associated with introducing high pressure of oxygen during the post-annealing.

• 전기전자학회논문지
• /
• 제22권4호
• /
• pp.1230-1233
• /
• 2018

에어로졸 데포지션 (aerosol deposition)공정을 통해 $Al_2O_3$막을 4H-SiC 상에 50 nm 두께로 제조하였고, 후열처리 공정에 따른 전기적 특성을 분석하였다. 그 결과 $N_2$분위기 열처리 시 $Al_2O_3$와 SiC 계면의 고정전하량이 감소하였으나 산소공공 생성에 의한 누설전류의 증가를 확인하였다. 본 결과로부터 계면특성 향상과 누설전류의 감소를 위해서는 적절한 $N_2$와 $O_2$가스의 혼합이 중요함을 확인하였다.

• 한국재료학회지
• /
• 제17권4호
• /
• pp.227-231
• /
• 2007

Transparent conducting indium tin oxide (ITO) films were deposited onto the Polyethersulfone (PES) substrate by using a magnetron sputter type negative metal ion source. In order to investigate the influence of cesium (Cs) partial pressure during deposition and annealing temperature on the optoelectrical properties of ITO/PES film the films were deposited under different Cs partial pressures and post deposition annealed under different annealing temperature from $100^{\circ}C$ to $170^{\circ}C$ for 20 min at $3\;{\times}\;10^{-1}$ Pa. Optoeleetrical properties of ITO films deposited without intentional substrate heating was influenced strongly by the Cs partial pressure and the Cs partial pressure of $1.5\;{\times}\;10^{-3}$ Pa was characterized as an optimal Cs flow condition. By increasing post-deposition vacuum annealing temperature both optical transmission in visible light region and electrical conductivity of ITO films were increased. Atomic force microscopy (AFM) micrographs showed that the surface roughness also varied with post-deposition vacuum annealing temperature.

• 한국세라믹학회지
• /
• 제37권8호
• /
• pp.731-738
• /
• 2000

KLN(K3Li2Nb5O15) has attracted a great deal of attention for their potential usefulness in piezoelectric, electro-optic, nonlinear optic, and pyroelectirc devices. Especially, the KLN single crystal has been studied in the field of optics and electronics. However it is hard to produce good quality single crystals due to the crack propagation during crystal growing. One of the solutions of this problem is prepartion of thin film. But the intensive study has not been conducted so far. In this study, after the KLN thin film were prepared by R.F. magnetron Sputtering method on SiO2/Si substrate, the post-annealing methods of RTA(rapid thermal annealin) and IPA(insitu post annealing) were employed. The deposition condition of KLN thin film was RF power(100 W), Working pressure(100 mtorr). The commonness of both RAT and IPA was that the higher were deposition and post annealing temperature, the higher was the intensity of XRD but the less surface roughness. The difference of post-annealing methods affected XRD phase and surface condition very much. And in IPA process, the influence of O2 had much effect on the formation of KLN phase.

• 한국재료학회지
• /
• 제15권11호
• /
• pp.741-744
• /
• 2005

Atomic layer deposition (ALD) is a very promising deposition technique for ZnO thin films. However, there have been very few reports on ZnO grown by ALD. Effects of substrate temperature in both ALD and post annealing on the microstructure and PL properties of ZnO thin films were investigated using X-ray diffraction, photoluminescence, and scanning electron microscopy. The temperature window of ALD is found to be between $130-180^{\circ}C$. The growth rate of ZnO thin film increases as the substrate temperature increases in the temperature range except the temperature window. The crystal quality depends most strongly on the substrate temperature among all the growth parameters of ALD. The crystallinity of the film is improved by increasing the growth thine per ALD cycle or doing post-annealing treatment. The grain size of the film tends to increase and the grain shape tends to change from a worm-like longish shape to a round one as the annealing temperature increases from $600^{\circ}C\;to\;1,000^{\circ}C$.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2000년도 하계학술대회 논문집 C
• /
• pp.1483-1484
• /
• 2000

Dielectric thin films of PLT(Pb(La.Ti)O3) for the application of highly integrated memory devices have been deposited on Pt/Ti/SiO2/Si substrates in situ by pulsed laser deposition(PLD). We have systematically investigated the variation of grain sizes depending on the condition of post-annealing and the variation of deposition rate. Both in-situ annealing and ex-situ annealing have been compared depending on the annealing time. C-V measurement, ferroelectric properties, leakage current and SEM were performed to investigate the electrical properties and the microstructural properties of Pb(La,Ti)$O_3$ films.