• Electrical & Electronic Materials
• /
• v.10 no.2
• /
• pp.97-104
• /
• 1997

In this paper, in order to investigate the behavior of charged particles on (Sr.Ca)TiO$_{3}$ ceramics with paraelectric properties, the characteristics of electrical conduction and thermally stimulated current was measured respectively. As a result, the conduction mechanism is divided into three regions having different mechanism as the current increased. The region I below 200[V/Cm] shows the ohmic conduction. The region B between 200[V/cm] and 2000[V/cm] can be explained by the Poole-Frenkel emission theory, and the region III above 2000[V/cm] is dominated by the tunneling effect. The three peaks of TSC were obtained at the temperature of -20[.deg. C], 20[.deg. C] and 80[.deg. C], respectively. The origins of these peaks are that the .alpha. peak observed at -20[.deg. C] looks like to be ascribed to the ionization excitation from donor level in the grain, and the .alpha.' peak observed at 20 [.deg. C] appears to show up by hopping conduction of the trapped carrier of border between the oxidation layer and the grain, and the .betha. peak observed at 80[.deg. C] seems to be resulted from hopping conduction of existing carrier in the trap site of the border between the oxidation and second phase.

• Korean Journal of Materials Research
• /
• v.33 no.6
• /
• pp.229-235
• /
• 2023

An all-perovskite oxide heterostructure composed of SrSnO₃/Nb-doped SrTiO₃ was fabricated using the pulsed laser deposition method. In-plane and out-of-plane structural characterization of the fabricated films were analyzed by x-ray diffraction with θ-2θ scans and φ scans. X-ray photoelectron spectroscopy measurement was performed to check the film's composition. The electrical transport characteristic of the heterostructure was determined by applying a pulsed dc bias across the interface. Unusual transport properties of the interface between the SrSnO₃ and Nb-doped SrTiO₃ were investigated at temperatures from 100 to 300 K. A diodelike rectifying behavior was observed in the temperature-dependent current-voltage (IV) measurements. The forward current showed the typical IV characteristics of p-n junctions or Schottky diodes, and were perfectly fitted using the thermionic emission model. Two regions with different transport mechanism were detected, and the boundary curve was expressed by ln I = -1.28V - 13. Under reverse bias, however, the temperature- dependent IV curves revealed an unusual increase in the reverse-bias current with decreasing temperature, indicating tunneling effects at the interface. The Poole-Frenkel emission was used to explain this electrical transport mechanism under the reverse voltages.

• Korean Journal of Materials Research
• /
• v.7 no.2
• /
• pp.107-113
• /
• 1997

$SrBi_{2}Ta_{2}O_{9}(SBT)$ thin films wcre prepared on $Pt/Ti/SiO_{2}/Si$ suhsrrate by pL~snia-enhanced chemical vapor deposition. Sr and Ta huhhling temperatures were kept ,it $120^{\circ}C$ Iron1 X- ray tiiffriict!on. n~icrostruc~ure. and composjrional analysis of SH7' films, respectivels Hi I~ut~t~lmg tempcl.arure was varied SR'I' thin tilrns dcpositcd ar i3i buhbling temperature of $130^{\circ}C$ have dielccrric constanr of 150 anti dissipation factor of 0 02 at IOOkFic. I .eakagc wrrent density of films was ahour $1.0{\times}10^{-8}A/cm^2$ at 20kV/cm. 1.eakage current i11amcrc1istic.s of Sli'l' films nras c.ontrolled by I'oole Frcnkel emission Kenianent polariziit~on and mercivc field oi SR\ulcorner' films annealed at $550^{\circ}C$ were $9{\mu}C/cm^2$ and 70kV/cm, respectively.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.12 no.4
• /
• pp.449-457
• /
• 2012

The program/erase (P/E) cyclic endurances including bias temperature instability (BTI) behaviors of Metal-$Al_2O_3$-Nitride-Oxide-Semiconductor (MANOS) memories are investigated in comparison with those of Semiconductor-Oxide-Nitride-Oxide-Semiconductor (SONOS) memories. In terms of BTI behaviors, the SONOS power-law exponent n is ~0.3 independent of the P/E cycle and the temperature in the case of programmed cell, and 0.36~0.66 sensitive to the temperature in case of erased cell. Physical mechanisms are observed with thermally activated $h^*$ diffusion-induced Si/$SiO_2$ interface trap ($N_{IT}$) curing and Poole-Frenkel emission of holes trapped in border trap in the bottom oxide ($N_{OT}$). In terms of the BTI behavior in MANOS memory cells, the power-law exponent is n=0.4~0.9 in the programmed cell and n=0.65~1.2 in the erased cell, which means that the power law is strong function of the number of P/E cycles, not of the temperature. Related mechanism is can be explained by the competition between the cycle-induced degradation of P/E efficiency and the temperature-controlled $h^*$ diffusion followed by $N_{IT}$ passivation.

• Proceedings of the KIEE Conference
• /
• 1998.11c
• /
• pp.795-797
• /
• 1998

A $BaTiO_3$, ferroelectric material, was mixed $SrTiO_3$, $(x)BaTiO_3-(1-x)SrTiO_3$($0.7{\leq}x{\leq}1$) ceramic capacitor with stable electrical properties in high voltage was fabricated. And microstructure, electrical property were investigated with $SrTiO_3$ mol ratio. The shrinkage, open porosity, sintering density were predominated at $9BaTiO_3-0.1SrTiO_3$. Increasing $SrTiO_3$ mol ratio, curie temperature was shifted at low temperature and maximum permittivity was increased. Also, $0.9BaTiO_3-0.1SrTiO_3$ was showed stable dielectric properties at $25{\sim}80[^{\circ}C]$. V-I properties of specimen were observed in the temperature range of $21{\sim}143[^{\circ}C]$, were divided into three regions. The region I below 10[kV/cm] was shown Ohmic conduction, the region II from 10 to 30[kV/cm] was explained by the Poole-Frenkel emission theory and the region III above 30[kV/cm] was analysed by the tunneling effect.

• Korean Journal of Materials Research
• /
• v.17 no.11
• /
• pp.574-579
• /
• 2007

Amorphous $BaTi_4O_9$ ($BT_4$) film was deposited on Pt/Si substrate by RF magnetron sputter and their dielectric properties and electrical properties are investigated. A cross sectional SEM image and AFM image of the surface of the amorphous $BT_4$ film deposited at room temperature showed the film was grown well on the substrate. The amorphous $BT_4$ film had a large dielectric constant of 32, which is similar to that of the crystalline $BT_4$ film. The leakage current density of the $BT_4$ film was low and a Poole-Frenkel emission was suggested as the leakage current mechanism. A positive quadratic voltage coefficient of capacitance (VCC) was obtained for the $BT_4$ film with a thickness of <70 nm and it could be due to the free carrier relaxation. However, a negative quadratic VCC was obtained for the films with a thickness ${\geq}96nm$, possibly due to the dipolar relaxation. The 55 nm-thick $BT_4$ film had a high capacitance density of $5.1fF/{\mu}m^2$ with a low leakage current density of $11.6nA/cm^2$ at 2 V. Its quadratic and linear VCCs were $244ppm/V^2$ and -52 ppm/V, respectively, with a low temperature coefficient of capacitance of $961ppm/^{\circ}C$ at 100 kHz. These results confirmed the potential suitability of the amorphous $BT_4$ film for use as a high performance metal-insulator-metal (MIM) capacitor.

• Proceedings of the KIEE Conference
• /
• 1997.07d
• /
• pp.1424-1426
• /
• 1997

저전압 구동이 가능한 교류구동형 박막전기발광소자를 구현하기 위해 높은 유전상수를 가지며 특히 광학적 굴절률이 발광박막과 유사하여 광학적 특성 개선에도 효과적인 것으로 알려져 있는 $Ta_2O_5$를 제조하였다. $Ta_2O_5$박막은 rf-magnetron sputtering방법으로 형성하였으며 기판온도, working pressure, 박막의 두께에 따른 전기적인 특성을 조사하였다. 10mTorr에서 제조된 $Ta_2O_5$박막은 $22{\sim}26$의 비유전율을 보였고, 유전손실은 $0.007{\sim}0.03(1kHz{\sim}10kHz)$의 값을 보였다. $100^{\circ}C$에서 제조된 박막의 전하저장용량은 $7.9{\mu}C/cm^2$이었다. 제조된 박막의 항복전압은 인가 전압의 극성에 의존하며, 전류특성은 기판온도와 200nm와 300nm의 두께에서는 $V^{1.95}{\sim}V^{2.35}$에 비례하는 space charge limited current특성을 보였고, 400nm에서는 Poole Frenkel특성을 보였다. 이상의 결과로 TFEL소자에 응용에 적합한 $Ta_2O_3$ 박막은 $200^{\circ}C$에서 증착되고 200nm와 300nm인 것으로 나타났으며, 제조된 MIS구조(ITO-$Ta_2O_5$-ZnS-Al)의 ACTFEL소자에서의 전도전하는 각각 $13uC/cm^2$, $8.3uC/cm^2$로 조사되었다.

• Korean Journal of Materials Research
• /
• v.27 no.1
• /
• pp.48-52
• /
• 2017

In this study, we used I-V spectroscopy, photoconductivity (PC) yield and internal photoemission (IPE) yield using IPE spectroscopy to characterize the Schottky barrier heights (SBH) at insulator-semiconductor interfaces of Pt/$HfO_2$/p-type Si metal-insulator-semiconductor (MIS) capacitors. The leakage current characteristics of the MIS capacitor were analyzed according to the J-V and C-V curves. The leakage current behavior of the capacitors, which depends on the applied electric field, can be described using the Poole-Frenkel (P-F) emission, trap assisted tunneling (TAT), and direct tunneling (DT) models. The leakage current transport mechanism is controlled by the trap level energy depth of $HfO_2$. In order to further study the SBH and the electronic tunneling mechanism, the internal photoemission (IPE) yield was measured and analyzed. We obtained the SBH values of the Pt/$HfO_2$/p-type Si for use in Fowler plots in the square and cubic root IPE yield spectra curves. At the Pt/$HfO_2$/p-type Si interface, the SBH difference, which depends on the electrical potential, is related to (1) the work function (WF) difference and between the Pt and p-type Si and (2) the sub-gap defect state features (density and energy) in the given dielectric.

• Transactions on Electrical and Electronic Materials
• /
• v.16 no.3
• /
• pp.124-129
• /
• 2015

Organic electronics are the domain in which the components and circuits are made of organic materials. This new electronics help to realize electronic and optoelectronic devices on flexible substrates. In recent years, organic materials have replaced conventional semiconductors in many electronic components such as, organic light-emitting diodes (OLEDs), organic field-effect transistors (OFETs) and organic photovoltaic (OPVs). It is well known that organic light emitting diodes (OLEDs) have many advantages in comparison with inorganic light-emitting diodes LEDs. These advantages include the low price of manufacturing, large area of electroluminescent display, uniform emission and lower the requirement for power. The aim of this paper is to model polymer LEDs and OLEDs made with small molecules for studying the electrical and optical characteristics. The purpose of this modeling process is, to obtain information about the running of OLEDs, as well as, the injection and charge transport mechanisms. The first simulation structure used in this paper is a mono layer device; typically consisting of the poly (2-methoxy-5(2'-ethyl) hexoxy-phenylenevinylene) (MEH-PPV) polymer sandwiched between an anode with a high work function, usually an indium tin oxide (ITO) substrate, and a cathode with a relatively low work function, such as Al. Electrons will then be injected from the cathode and recombine with electron holes injected from the anode, emitting light. In the second structure, we replaced MEH-PPV by tris (8-hydroxyquinolinato) aluminum (Alq₃). This simulation uses, the Poole-Frenkel -like mobility model and the Langevin bimolecular recombination model as the transport and recombination mechanism. These models are enabled in ATLAS- SILVACO. To optimize OLED performance, we propose to change some parameters in this device, such as doping concentration, thickness and electrode materials.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2000.02a
• /
• pp.69-69
• /
• 2000

(Ba, Sr)TiO3 (BST)[1-3] 박막은 유전상수가 크고 고주파에서도 유전특성 저하가 적기 때문에 ULSI DRAM(Dynamic Random Access Memory)에 응용 가능한 물질로 최근 각광을 받고 있다. 하지만, 아직 BST 박막을 DRSM에 바로 적용하기 위해선 몇 가지 문제점이 있다. 그 중 누설전류 문제는 디바이스 응용시 매우 중요한 요소이다. 특히, DRAM에서 refresh time와 직접적인 관련이 있어 디바이스 내의 신뢰도 및 전력소모를 결정하는 주된 인자가 된다. 지금까지, BST 박막의 인가전업, 온도, 그리고 전극물질에 따른 누설전류 현상들이 고찰되었고, 이에 관한 많은 전도기구 모델들이 제시되었다. Schottky emission, Poole-Frenkel emission, space charge limited conduction 등이 그 대표적인 예이다. 하지만 아쉽게도 BST 박막의 정확한 누설 전류 전도 기구를 완전히 설명하는데는 아직 한계가 있다. 따라서 본 연구에서는 제작된 BST 커패시터 내의 기본적인 전기적 성질을 조사하고, 정확한 누설전류 기구 규명에 초점을 두고자 한다. 이를 위해 기존의 여러 기구들과 비교 분석할 것이다. 하부전극으로 사용하기 위해 스퍼터링 방법으로 p-Si(100) 기판위에 RuO2 박막을 약 120nm 증착하였다. 증착전의 chamberso의 초기압력은 5$\times$10-6 Torr이하의 압력으로 유지시켰다. Ar/O2의 비는 이전 실험에서 최적화된 9/1로 하였다. BST 박막 증착 시 5분간 pre-sputtering을 실시한 후 하부전극 기판위에 BST 박막을 증착하였다. 증착이 끝난 후 시편을 상온까지 냉각시킨 후 꺼내었다. 전기적 특성을 측정하기 상부전극으로 RuO2와 Al 박막을 각각 상온에서 100nm 증착하였다. 이때 hole mask를 이용하여 반경이 140um인 원형의 상부전극을 증착하였다. BST 박막의 증착온도가 증가하고 Ar/O2 비가 감소할수록 제작된 BST-커패시터의 전기적 성질이 우수하였다. 증착온도 $600^{\circ}C$, ASr/O2=5/5에서 증착된 막의 누설전류는 4.56$\times$10-8 A/cm2, 유전상수는 600 정도의 값을 나타내었다. 인가전압에 따른 BST 커패시터의 transition-current는 Curie-von Schweider 모델을 따랐다. BST 박막의 누설전류 전도기구는 기존의 Schottky 모델이 아니라 modified-Schottky 무델로 잘 설명되었다. Modified-Schottky 모델을 통해 BST 박막의 광학적 유전율 $\varepsilon$$\infty$=4.9, 이동도 $\mu$=0.019 cm2/V-s, 장벽 높이 $\psi$b=0.79 eV를 구하였다.