• 반도체디스플레이기술학회지
• /
• 제15권2호
• /
• pp.81-86
• /
• 2016

Moisture vapor transmission rate (MVTR) is an important item for many applications of polymer breathable thin film. To determine the optimum values of the process parameters, it is essential to find their influence on The significance of six important process parameters namely, extruder cylinder temperature, extruder speed, extruder dies temperature, cooling roll temperature, stretching ratio, stretching roll temperature on breathable film strength of polymer extrusion was determined. Moreover, this paper presents the application of Taguchi method and analysis of variance (ANOVA) for maximization of the breathable film MVTR influenced by extrusion parameters. The optimum parameter combination of extrusion process was obtained by using the analysis of signal-to-noise ratio. The conclusion revealed that extruder speed and stretching ratio were the most influential factor on the film strength, respectively. The best results of film MVTR were obtained at higher extruder speed and stretching ratio.

• 한국고분자학회:학술대회논문집
• /
• 한국고분자학회 2006년도 IUPAC International Symposium on Advanced Polymers for Emerging Technologies
• /
• pp.369-369
• /
• 2006

Compatibilizers contribute to many processes in polymer industry, such as manufacturing polymer blends and composites. They are usually designed to be block or graft form which is combined in polar and non-polar parts in the first synthesis process level, for example, the general form of maleic anhydride (MA) as a compatiblizer is a grafted counterpart. However, the process of making the compatibilizer is related to the first synthesis level and it has some problems, such as high cost, poor processability, limitation on use and properties, and so on. So, in order to improve its poor processability and overcome the limitation on use, we developed compatibilizers which have various chemical forms by high intensity ultrasound and super critical fluid nitrogen in polymer melt reactive extrusion.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1997년도 추계학술대회 논문집
• /
• pp.585-590
• /
• 1997

Conventional foaming process has defects such as lower mechanical properties than ur~foaming material due to non-uniform cell distribution and environmental pollution problem caused by chemical blowing agency. So, a new foaming process such as Microcelluar plastics has been introduced to use inactive gases as a foaming agency. In order to apply Microcellular plastics for mass production process system such as extrusion, injection molding and blow molding, it needs to predict the change in material properties of polymer according to the amount of meltingas. In Polymer molding applying Microcelluar plastics, the change of viscosity among several material properties is the most important factor. Therefore, this paper is aimed to establish the method which not only finds out but also predicts the change of viscosity of ABS(Acrylonitri1e Butadiene Styrene) resin according to inert gas amount in extrusion molding.

• 한국생산제조학회지
• /
• 제18권6호
• /
• pp.585-589
• /
• 2009

Extruder is divided to greatly three part at extrusion process. First, by hopper(Hopper) second, barrel(Barrel) with Screw that is point of extruder and third that is raw material supply wealth extrusion into dies(DIES) Part that decide shape of do product greatly divide. Hopper is role that distribute in raw material supply wealth (Feeding zone) of Screw preserving raw material in state of high quality how at extrusion process, and make distributed raw material as Screw in barrel rotates and 3 stage and inflicting heat and pressure raw material melting(Melting) state. And raw material of melting state Screw's measuring stoker(Metering zone) whereabouts anaphora do and product is completed through pipe channel of dies. Dies that is the most important as Screw in extrusion is part that is last part of melting state process of raw material and causes huge effect in quality of product. If more than design of dies happens, manufacture itself of dies is hard, but there are a lot of amount of losses accordingly. In this research, make pipe channel that raw material of melting state flows in dies can present dies basic design method through flow analysis of ideal pipe channel using CFdesign.

• 폴리머
• /
• 제29권2호
• /
• pp.198-203
• /
• 2005

용융 압출 발포에 의하여 폴리락틱산(PLLA) 지지체를 제조하고 발포 조건이 지지체의 구조와 기계적 특성에 미치는 영향을 살펴보고 이를 염 추출법에 의하여 제조된 지지체와 비교하였다. 발포제를 함유한 PLLA 용융체가 압출기 및 다이에서 체류하는 시간이 발포제의 무게를 최대로 감소시키는 시간과 일치하여야 최적의 PLLA 지지체의 구조를 얻을 수 있음을 확인하였다. PLLA지지체의 구조를 유지하기 위해서는 발포제의 함량을 $10\;wt\%$ 이하로 조절해야 하며 PLLA 지지체의 다공도는 PLLA의 압출기에서의 체류시간에 가장 큰 영향을 받음을 알 수 있었다. 용융 압출 발포에 의하여 얻어진 지지체는 일반적으로 염 추출법에 의하여 제조된 지지체보다 다소 낮은 다공도를 갖지만 발포 조건의 조절에 의하여 적절한 다공 크기와 다공의 연결성을 가지며 동시에 우수한 기계적 특성을 가져 경조직 재생(hard tissue regeneration)용으로 사용이 가능할 것으로 사료된다.

• Carbon letters
• /
• 제16권2호
• /
• pp.86-92
• /
• 2015

Multi-walled carbon nanotube (MWCNT)/polycarbonate (PC) nanocomposite was prepared by direct melt mixing to investigate the effect of the shear rate on the surface resistivity of the nanocomposites. In this study, an experiment was carried out to observe the shear induced orientation of the MWCNT in the polymer matrix using a very simple melt flow indexer with various loads. The compression-molded, should be eliminated. MWCNT/PC nanocomposite sample exhibited lower percolation thresholds (at 0.8 vol%) and higher electrical conductivity values than those of samples extruded by capillary and injection molding. Shear induced orientation of MWCNT was observed via scanning electron microscopy, in the direction of flow in a PC matrix during the extrusion process. The surface resistivity rose with increasing shear rate, because of the breakdown of the network junctions between MWCNTs. For real applications such as injection molding and the extrusion process, the amount of the MWCNT in the composite should be carefully selected to adjust the electrical conductivity.

• 한국산학기술학회논문지
• /
• 제19권9호
• /
• pp.77-83
• /
• 2018

열가소성 탄성체 (Thermo-Plastic Elastomer-TPE)는 우수한 탄성을 지니면서도 보통의 열가소성 플라스틱과 동일한 성형성과 재생 가능성 때문에 산업계 전반에 걸쳐 사용이 증가하고 있다. 현재 열가소성 탄성체와 관련된 연구는 다양한 소재와의 결합에 의한 복합탄성체 개발이나 이를 구현하기 위한 장비 개발 등에 집중되고 있다. 반면 중소기업 등의 현장에서는 이러한 신소재의 적용뿐만 아니라 저렴한 일축 스크류 장비에서 열가소성 탄성체의 압출이 가능하게 하는 공정조건에 대한 연구가 필요하다. 열가소성 탄성체는 일반적으로 트윈 스크류 방식으로 압출을 하게 된다. 반면에 중소기업 등에서는 단축 스크류 방식의 압출기를 주로 보유하고 있는데 단축 스크류 방식의 압출기에서 압출이 가능하게 하려면 정교한 공정제어를 통해 균일한 두께 유지가 중요하다. 본 논문에서는 열가소성 탄성체 TPE-800L 단축 압출가공에 있어서 압출공정변수인 출력부 가공 온도가 튜브의 성형성에 미치는 영향을 연구하였다. 열가소성 탄성체 TPE-800L의 압출에서는 출력부 온도가 가장 중요한 요소이며 165-170도일 때 가장 우수한 성형성을 확인하였다.

• Macromolecular Research
• /
• 제16권1호
• /
• pp.6-14
• /
• 2008

Polypropylene (PP)-layered silicate nanocomposites were developed using a new processing method involving a supercritical carbon dioxide ($scCO_2$)-assisted co-rotating twin-screw extrusion process. The nanocomposites were prepared through two step extrusion processes. In the first step, the PP/clay mixture was extruded with $CO_2$ injected into the barrel of the extruder and the resulting foamed extrudate was cooled and pelletized. In the second step, the foamed extrudate was extruded with venting to produce the final PP/clay nanocomposites without $CO_2$. In this study, organophilic-clay and polypropylene matrix were used. Maleic anhydride grafted polypropylene (PP-g-MA) was used as a compatibilizer. This study focused on the effect of $scCO_2$ on the dispersion characteristics of the clays into a PP matrix and the rheological properties of the layered silicate based PP nanocomposites. The dispersion properties of clays in the nanocomposites as well as the rheological properties of the nanocomposites were examined as a function of the PP-g-MA concentration. The degree of dispersion of the clays in the nanocomposites was analyzed by X-ray diffraction and transmission electron microscope. Various rheological properties of the nanocomposites were measured using a rotational rheometer. In the experimental results, the $scCO_2$ assisted continuous manufacturing extrusion system was used to successfully produce the organophilic-clay filled PP nanocomposites. It was found that $scCO_2$ had a measurable effect on the clay dispersion in the polymer matrix and the melt intercalation of a polymer into clay layers.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2013년도 춘계학술대회 논문집
• /
• pp.1169-1170
• /
• 2013

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2005년도 추계학술대회 논문집
• /
• pp.1046-1050
• /
• 2005

Micro Cellular Plastics create a sensation at polymer industrial for lowering product cost & overcoming a lowering of mechanical intensity. There Is much development from injection molding pans but Extrusion parts is slow. This research is MCPs Extrusion parts, It is basis experiment for Process to make beads that is basis raw material of Package used most by shock mitigative of industry.